Poulan 437685 To Remove Wheels See Fig, Carburetor, Engine Speed, To Adjust Cable Tension See Fig

Page 18

SERVICE AND ADJUSTMENTS

TO REMOVE WHEELS (See Fig. 22)

•Remove the klik pin and remove wheel from axle.

IMPORTANT: When installing wheel, be sure to use the axle hole closest to the end of the shaft – do not use the hole in the wheel hub (if equipped). Inner hole in axle and hole in wheel hub are not used for your model snow thrower.

KLIK PIN (INSTALL

OUTER HOLE

IN OUTER HOLE

 

OF AXLE ONLY)

 

AXLE

WHEEL

WHEEL HUB

FIG. 22

NOTE: To seal punctures or prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

ENGINE

See engine manual.

CARBURETOR

Your carburetor is not adjustable. Engine performance should not be affected at altitudes up to 7,000 feet (2,134 meters). If your engine does not operate properly due to suspected carburetor problems, take your snow thrower to a qualified service center.

ENGINE SPEED

Never tamper with the engine governor, which is factory set for proper engine speed. Overspeeding the engine above the factory high speed setting can be dangerous and will void the warranty. If you think the engine-governed high speed needs adjusting, contact a qualified service center, which has proper equipment and experience to make any necessary adjustments.

TO ADJUST CABLE TENSION (See Fig. 23)

Adjust cable tension by turning the adjuster turn buckle, located on the right hand cable. Grasp the long section tightly and turn the short section to lengthen the adjuster. Adjust until cable is snug.

ADJUSTER TURN

BUCKLE

FIG. 23

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from CartonInstall Speed Control ROD See Figs Install Traction Drive Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotater Head See FigInstall Chute Deflector Remote Control See Figs Check Tire PressurePrimer OperationKnow Your Snow Thrower Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineTo USE Choke Control See Fig HOW to USE Your Snow ThrowerStopping To Control Snow Discharge See FigTo Throw Snow See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Move Forward and Backward See FigScraper BAR See Fig To Adjust Skid Plates See FigBefore Starting the Engine Check Engine OIL Level See FigBefore Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has FrozenBefore Each USE MaintenanceGeneral Recommendations LubricationCleaning EngineChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See FigTo Replace Belts See Fig Carburetor To Adjust Cable Tension See FigTo Remove Wheels See Fig Engine SpeedFuel System StorageOther Engine OILTroubleshooting Service Notes Exploded KEY Part Description Auger Bearing Auger HousingScraper BAR Bearing PlugSkid Plate LH Auger 27 LHAuger 27 RH Skid Plate RHPOP Rivet Deflector SealKnob Black Chute Snow Shield 419822X431 Shield Retainer StrapCable Assembly Heat Shield LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Rotator HeadLower Handle Loop Handle LHLoop Handle RH Pivot Support WeldmentKnob RED SpacerRetainer Handle KnobCarriage Bolt 5/16-18 X 155377 NUT 5/16-18 169675 Headlight Bezel Wire HarnessConsole Panel Flood HeadlightRepair Parts Snow Thrower - Model Number PP1150E27 Drive Wheel HUB Speed Selector AssemblyDrive Plate Assembly END PlateAxle Shaft Sprocket436146X428 ENGINE, B&SFrame Engine Mount PlateIdler ARM Bracket Impeller BeltTraction Belt Idler Pulley428684 Wheel Assembly LH Cable Bracket LHCable Bracket RH Wheel Lobe CoverWheel Driver Retainer Ring Clutch SlideSafety Ignition KEY 193071Shifter ROD TOP Shifter ROD Bottom DECAL, DANGER, Deflector 181037DECAL, Danger DECAL, InstructionService Notes Limited Warranty

437685, 96198003304 specifications

The Poulan 96198003304,437685 chainsaw is a robust and reliable tool designed for both professional arborists and home users alike. Known for its powerful performance and user-friendly features, this chainsaw has become a popular choice for a variety of cutting tasks, including tree trimming, pruning, and firewood preparation.

One of the standout features of the Poulan 96198003304,437685 is its potent engine. Equipped with a high-performance two-stroke engine, this chainsaw delivers impressive cutting power, making it capable of handling larger logs and tougher jobs with ease. The engine is designed to provide optimal balance between power and fuel efficiency, ensuring users can work longer without frequent refueling.

Additionally, the chainsaw features an ergonomic design with lightweight construction, allowing for extended use without causing undue strain on the operator. The integrated anti-vibration system further enhances comfort, absorbing shocks and reducing fatigue during operation. This is particularly important for users who need to operate the saw for longer periods.

The Poulan chainsaw also excels in safety and ease of use. It incorporates features such as a chain brake, which stops the chain immediately in the event of kickback, and an automatic oiling system that ensures the chain is lubricated while in use. This not only prolongs the life of the chain and bar but also enhances cutting efficiency.

Maintenance is made simple with the tool-less chain tensioning system, allowing users to quickly adjust the chain without the need for additional tools. This feature saves time and ensures that the chainsaw is always ready for action.

Another technological advantage of the Poulan 96198003304,437685 is its fuel-efficient design, which reduces emissions and minimizes environmental impact. This aligns with the growing need for eco-friendly tools in the market.

Overall, the Poulan 96198003304,437685 chainsaw stands out due to its powerful performance, user-friendly features, and commitment to safety and efficiency. Whether you are a seasoned professional or a beginner, this chainsaw offers the reliability and functionality you need for effective and enjoyable cutting tasks.
Top Page Image Contents