Loop Handle LH, Loop Handle RH, Lower Handle

Poulan 437685, 96198003304 Loop Handle LH, Loop Handle RH, Lower Handle, Pivot Support Weldment

Page 28

REPAIR PARTS SNOW THROWER - - MODEL NUMBER PP1150E27 (96198003304)

HANDLES

		KEY	PART	DESCRIPTION
4	4	NO.	NO.	DESCRIPTION
4		1	419798X431	LOOP HANDLE LH
	1	2	419799X431	LOOP HANDLE RH
3		3	74780524	SCREW 5/16−18 X 1.50
3		4	751153	NUT 5/16−18
4		4	751153	NUT 5/16−18
4
3
2

01.08.004-B

	KEY	PART	DESCRIPTION
	NO.	NO.	DESCRIPTION
2	1	419797X431	LOWER HANDLE
	2	427513X431	PIVOT SUPPORT WELDMENT
4	3	428867	SCREW 5/16−18 X .750
4	4	17000616	SCREW 3/8−16 X 1.00
	4	17000616	SCREW 3/8−16 X 1.00
	3

01-05-013-A

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 28

Image 28

Contents

Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerParts Packed Separately in Carton Remove Snow Thrower from CartonInstall Traction Drive Control ROD See Figs Install Speed Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotater Head See FigInstall Chute Deflector Remote Control See Figs Check Tire PressureOperation Know Your Snow ThrowerPrimer Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineHOW to USE Your Snow Thrower StoppingTo USE Choke Control See Fig To Control Snow Discharge See FigUsing the CLEAN-OUT Tool See Fig Power Steering Operation See FigTo Throw Snow See Fig To Move Forward and Backward See FigTo Adjust Skid Plates See Fig Before Starting the EngineScraper BAR See Fig Check Engine OIL Level See FigSnow Throwing Tips To Start EngineBefore Stopping If Recoil Starter has FrozenMaintenance General RecommendationsBefore Each USE LubricationCleaning EngineService and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See FigTo Replace Belts See Fig To Adjust Cable Tension See Fig To Remove Wheels See FigCarburetor Engine SpeedStorage OtherFuel System Engine OILTroubleshooting Service Notes Exploded KEY Part Description Auger Housing Scraper BARAuger Bearing Bearing PlugAuger 27 LH Auger 27 RHSkid Plate LH Skid Plate RHDeflector Seal Knob BlackPOP Rivet Chute Snow Shield 419822X431 Shield Retainer StrapLEVER/CABLE Rotator Assembly Cable Assembly AdjustableCable Assembly Heat Shield Rotator HeadLoop Handle LH Loop Handle RHLower Handle Pivot Support WeldmentSpacer RetainerKnob RED Handle KnobCarriage Bolt 5/16-18 X 155377 NUT 5/16-18 169675 Wire Harness Console PanelHeadlight Bezel Flood HeadlightRepair Parts Snow Thrower - Model Number PP1150E27 Drive Speed Selector Assembly Drive Plate AssemblyWheel HUB END PlateAxle Shaft SprocketENGINE, B&S Frame436146X428 Engine Mount PlateImpeller Belt Traction BeltIdler ARM Bracket Idler Pulley428684 Cable Bracket LH Wheel Assembly LHCable Bracket RH Cover Wheel Driver Retainer RingWheel Lobe Clutch SlideSafety Ignition KEY 193071Shifter ROD TOP Shifter ROD Bottom 181037 DECAL, DangerDECAL, DANGER, Deflector DECAL, InstructionService Notes Limited Warranty

Poulan 437685, 96198003304 Loop Handle LH, Loop Handle RH, Lower Handle, Pivot Support Weldment

REPAIR PARTS SNOW THROWER - - MODEL NUMBER PP1150E27 (96198003304)

HANDLES

KEY

LOOP HANDLE LH

LOOP HANDLE RH

KEY

LOWER HANDLE

PIVOT SUPPORT WELDMENT