Poulan 96198003304, 437685 owner manual Meets A.N.S.I. Safety Requirements

Page 9

OPERATION

GASOLINE

FILLER CAP

MUFFLER

CHOKE CON-

TROL

PRIMER

SAFETY

IGNITION

KEYON / OFF SWITCH

NOTE: ITEMS ABOVE

ARE SHOWN IN

THEIR TYPICAL

LOCATION ON THE

ENGINE. ACTUAL

LOCATION MAY

VARY WITH THE

ENGINE ON YOUR

UNIT.

AUGERS

ELECTRIC AUGER

START BUTTON CONTROL LEVER

RECOIL (AUXILIARY)

STARTER

HANDLE

CHUTE

DEFLECTOR

DISCHARGE

CHUTE

CLEAN-OUT TOOL

FIG. 10

DISCHARGE CHUTE CONTROL LEVER

DRIVE SPEED

DEFLECTOR REMOTE

CONTROL LEVER

CONTROL LEVER

TRACTION

DRIVE

CONTROL

LEVER

LH TURN

TRIGGER

LIGHT

HANDLE

KNOB

MUFFLER

TOOLBOX

SKID PLATE

MEETS A.N.S.I. SAFETY REQUIREMENTS

Our snow throwers conform to the standards of the American National Standards Institute.

Toolbox - used to store spare shear bolts, locknuts and wrench.

Safety ignition key - must be inserted for the engine to start and run. Remove when snow thrower is not in use.

Electric start button – used for starting the engine.

Recoil (auxiliary) starter handle – used for starting the engine.

Primer - pumps additional fuel from the carburetor to the cylinder for use when starting a cold engine.

Throttle/engine control - used to select either FAST or SLOW engine speed and to STOP the engine.

Choke control - used for starting a cold engine. ON / OFF switch - used to STOP the engine.

LH and RH turn triggers - used to steer the snow thrower.

Drive speed control lever - used to select forward or reverse motion and speed of snow thrower.

Traction drive control lever - used to engage power- propelled forward or reverse motion of snow thrower.

Auger control lever - used to engage auger motion (throw snow).

Discharge chute control lever - used to change the direc- tion the snow is thrown.

Skid plate - used to adjust height of scraper bar from the ground

Deflector remote control lever - used to change the distance the snow is thrown.

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents
Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONParts Packed Separately in Carton Remove Snow Thrower from CartonInstall Speed Control ROD See Figs Install Traction Drive Control ROD See FigsUnfold Upper Handle Install Discharge Chute / Chute Rotater Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Install Chute Deflector Remote Control See FigsKnow Your Snow Thrower OperationPrimer Ignition KEYRecoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerTo USE Choke Control See Fig To Control Snow Discharge See FigPower Steering Operation See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig To Move Forward and Backward See FigBefore Starting the Engine To Adjust Skid Plates See FigScraper BAR See Fig Check Engine OIL Level See FigTo Start Engine Snow Throwing TipsBefore Stopping If Recoil Starter has FrozenGeneral Recommendations MaintenanceBefore Each USE LubricationEngine CleaningTo Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See FigTo Replace Belts See Fig To Remove Wheels See Fig To Adjust Cable Tension See FigCarburetor Engine SpeedOther StorageFuel System Engine OILTroubleshooting Service Notes Exploded KEY Part Description Scraper BAR Auger HousingAuger Bearing Bearing PlugAuger 27 RH Auger 27 LHSkid Plate LH Skid Plate RHKnob Black Deflector SealPOP Rivet Chute Snow Shield 419822X431 Shield Retainer StrapCable Assembly Adjustable LEVER/CABLE Rotator AssemblyCable Assembly Heat Shield Rotator HeadLoop Handle RH Loop Handle LHLower Handle Pivot Support WeldmentRetainer SpacerKnob RED Handle KnobCarriage Bolt 5/16-18 X 155377 NUT 5/16-18 169675 Console Panel Wire HarnessHeadlight Bezel Flood HeadlightRepair Parts Snow Thrower - Model Number PP1150E27 Drive Drive Plate Assembly Speed Selector AssemblyWheel HUB END PlateSprocket Axle ShaftFrame ENGINE, B&S436146X428 Engine Mount PlateTraction Belt Impeller BeltIdler ARM Bracket Idler Pulley428684 Wheel Assembly LH Cable Bracket LHCable Bracket RH Wheel Driver Retainer Ring CoverWheel Lobe Clutch Slide193071 Safety Ignition KEYShifter ROD TOP Shifter ROD Bottom DECAL, Danger 181037DECAL, DANGER, Deflector DECAL, InstructionService Notes Limited Warranty