Poulan 96192003201, 429896 owner manual Engine, Cleaning

Page 15

MAINTENANCE

BELTS

Check belts for deterioration and wear after every 50 hours of operation and replace if necessary. The belts are not adjustable. Replace belts if they begin to slip from wear. (See “TO REMOVE BELT COVER” in the Service and Adjustments section of this manual).

The belts on your snow thrower are of special construction and should be replaced by original equipment manufacturer (OEM) belts available from your nearest dealer. Using other than OEM belts can cause personal injury or damage to the snow thrower.

AUGER GEAR CASE

The gear case was filled with lubricant to the proper level at the factory. The only time the lubricant needs attention is if service has been performed on the gear case.

If lubricant is required, use only Ronex ED #1 grease.

TRACTION DRIVE SYSTEM

DO NOT lubricate the drive components inside the snow thrower. The sprockets, hex shafts, drive disc and friction wheel require no lubrication. The bearings and bushings are lifetime lubricated and require no maintenance.

CAUTION: Any lubricating of the above compo- nents can cause contamination of the friction wheel and damage to the drive system of your snow thrower.

ENGINE

See engine manual.

LUBRICATION

Use only high quality detergent oil rated with API service classification SG–SL. Select the oil's SAE viscosity grade according to your expected operating temperature.

NOTE: Although multi-viscosity oils (5W30, 10W30 etc.) improve starting in cold weather, these multi-viscosity oils will result in increased oil consumption when used above 32°F. Check your engine oil level more frequently to avoid possible engine damage from running low on oil.

Change the oil after every 25 hours of operation or at least once a year if the snow thrower is not used for 25 hours in one year.

Check the crankcase oil level before starting the engine and after each five (5) hours of continuous use. Tighten oil fill cap / dipstick securely each time you check the oil level.

TO CHANGE ENGINE OIL

Determine temperature range anticipated before next oil change. All oil must meet API service classification SG–SL.

Be sure snow thrower is on level surface.

Oil will drain more freely when warm.

Catch oil in a suitable container.

NOTE: The left side wheel may be removed from snow thrower for easier access to the oil drain plug and place- ment of a suitable container. The unit tilted, resting on the frame with the left wheel removed, will help drain any oil trapped inside the engine. (See “TO REMOVE WHEELS” in the Service and Adjustments section of this manual).

1.Remove safety ignition key and disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

2.Clean area around drain plug.

3.Remove drain plug and drain oil in a suitable container.

4.Install drain plug and tighten securely.

5.Wipe off any spilled oil from snow thrower and engine.

6.Install left wheel (if removed for draining oil). Be sure to install klick pin into proper hole in wheel axle (See “TO REMOVE WHEELS” in the Service and Adjustments section of this manual).

7.Remove oil fill cap/dipstick. Be careful not to allow dirt to enter the engine.

8.Refill engine with oil through oil dipstick tube. Pour slowly. Do not overfill. For approximate capacity see “PRODUCT SPECIFICATIONS” section of this manual.

9.Use gauge on oil fill cap/dipstick for checking level. Be sure dipstick cap is tightened securely for accurate reading. Keep oil at “FULL” line on dipstick.

10.Wipe off any spilled oil.

MUFFLER

Inspect and replace corroded muffler as it could create a fire hazard and/or damage.

SPARK PLUG

Replace spark plug at the beginning of each season or after every 100 hours of operation, whichever occurs first. Spark plug type and gap setting are shown in the “PRODUCT SPECIFICATIONS” section of this manual.

CLEANING

IMPORTANT: For best performance, keep snow thrower housing free of any dirt or trash. Clean the outside of your snow thrower after each use.

WARNING: Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

Keep finished surfaces/wheels free of gasoline, oil, etc.

We do not recommend using a garden hose to clean your snow thrower unless the electrical system, muffler and carburetor are covered to keep water out. Water in engine can result in shortened engine life.

15

Image 15
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Parts Packed Separately in CartonInstall Speed Control ROD See Figs Install Traction Drive Control ROD See FigsUnfold Upper Handle Install Discharge Chute / Chute Rotater Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Install Chute Deflector Remote Control See FigsIgnition KEY OperationKnow Your Snow Thrower PrimerRecoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Adjust Skid Plates See FigCheck Engine OIL Level See Fig Before Starting the EngineScraper BAR See Fig To USE Drift Cutters See FigIf Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before StoppingLubrication MaintenanceGeneral Recommendations Before Each USEEngine CleaningShear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Replace Belts See Fig Engine Speed To Adjust Cable Tension See FigTo Remove Wheels See Fig CarburetorEngine OIL StorageOther Fuel SystemTroubleshooting KEY Part Description 23 22 Impeller Pulley Gearbox Assembly178675X008 Corner Bracket Clean OUT Tool BearingAuger Assembly 30 RH Auger Assembly 30 LHPlastic Washer Weight BARDrift Cutter BAR CARRIAGEBOLT5/16−18X.750Chute Snow Shield Deflector Spring 15 420679 Service Part Deflector ControlKnob Black POP RivetRotator Pivot Bracket LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Rotator HeadPivot Support Loop Handle LHLoop Handle RH Lower TubeShifter ROD Bottom Impeller ROD AssemblyTraction ROD Assembly Shifter ROD TOPHalogen Headlight Wire HarnessPanel Console Headlight BezelRepair Parts Snow Thrower - Model Number PR1330ES Drive Exploded Rubber Ring AssemblyDrive Plate Assembly Speed SelectorEngine Mounting Plate Complete LCT EngineFrame 427963X428Idler Pulley Impeller BeltTraction Belt Idler ARM BracketWheel Assembly LH Cable Bracket LHCable Bracket RH Clutch Slide CoverWheel Driver Retainer Ring Wheel Lobe422663 Safety Ignition KEY181037 DECAL, DangerDECAL, DANGER, Deflector Limited Warranty

96192003201, 429896 specifications

The Poulan 429896,96192003201 is a high-performance chainsaw designed for both professional and residential use. This versatile tool is particularly favored for its robust features that enhance efficiency and ease of use.

One of the standout characteristics of the Poulan 429896 is its powerful engine. Equipped with a high-performance 42cc engine, this chainsaw provides ample power for cutting through tough wood and dense materials with ease. The engine is designed to deliver optimal torque and power, allowing users to complete tasks quickly without compromising on performance.

The chainsaw features a 16-inch bar and chain, ideal for a wide range of cutting applications. This size strikes a perfect balance between maneuverability and cutting capacity, making it suitable for trimming branches, felling small trees, and performing maintenance tasks around the yard. The bar and chain are designed for durability and long life, ensuring that the saw remains operational through extensive use.

One of the most valuable technologies integrated into the Poulan 429896 is the Easy Start feature. This function minimizes the effort required to start the engine, making it accessible for users of various skill levels. Whether you are a seasoned professional or a weekend warrior, the Easy Start technology ensures a hassle-free experience.

In terms of safety, the Poulan 429896 incorporates several features that enhance user protection. The chainsaw is equipped with a chain brake that engages automatically in the event of kickback, an essential safety feature that helps prevent accidents. Additionally, the ergonomic design of the handle provides a comfortable grip while minimizing vibrations, allowing for longer periods of use without discomfort.

Maintenance is also a key consideration with the Poulan 429896. The chainsaw is designed for easy access to the air filter and spark plug, making routine maintenance tasks more straightforward. This user-friendly design ensures that the chainsaw remains in peak condition for years to come.

Overall, the Poulan 429896,96192003201 stands out for its combination of power, efficiency, and safety. Whether you are tackling heavy-duty landscaping projects or light pruning, this chainsaw offers the reliability and performance needed to get the job done effectively. With its durable construction and user-friendly features, the Poulan 429896 is an excellent choice for anyone in need of a dependable chainsaw.