Poulan 429896 owner manual Service and Adjustments, To Adjust Snow Thrower Height, Chute Deflector

Page 16

SERVICE AND ADJUSTMENTS

WARNING: To avoid serious injury, before performing any service or adjustments:

1.Be sure the on/off switch is in the OFF position.

2.Remove safety ignition key.

3.Make sure the augers and all moving parts have completely stopped.

4.Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

1.Disengage all controls and move throttle control to STOP position. Wait for all moving parts to stop.

2.Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with spark plug.

3.Align holes in impeller hub with holes in impeller shaft and install two (2) new 1/4-20 x 1-5/8" capscrew/shear bolts. Install 1/4-20 locknuts and tighten securely.

CAUTION: Do not substitute. Use only original equipment capscrew/shear bolts as supplied with your snow thrower.

SNOW THROWER

TO ADJUST SNOW THROWER HEIGHT

See “TO ADJUST SKID PLATES” and “SCRAPER BAR” in the Operation section of this manual.

CHUTE DEFLECTOR

The chute deflector, attached to the top of the discharge chute, is provided to direct discharging snow away from the operator. If the deflector becomes damaged, it should be replaced.

WARNING: To avoid serious injury, never operate your snow thrower with the deflector removed or damaged.

To change direction and/or distance snow is discharged, see “TO CONTROL SNOW DISCHARGE” in the Op- eration section of this manual.

SHEAR BOLTS (See Fig. 21)

AUGER SHEAR BOLTS

Both right and left-hand augers are secured to the auger shaft with a spacer, shear bolt and hex nut. Should a foreign object or ice become lodged in the augers, the shear bolts are designed to break, preventing damage to any other components. If one or both augers do not turn when auger control lever is engaged, check to see if one or both of the bolts have sheared. To replace the shear bolts:

1.Disengage all controls and move throttle control to STOP position. Wait for all moving parts to stop.

2.Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with spark plug.

3.Align hole in auger hub with hole in auger shaft and install a new 1/4-20 x 2" shear bolt. Install 1/4-20 lock nut and tighten securely.

CAUTION: Do not substitute. Use only original equipment shear bolts as supplied with your snow thrower.

4.Insert safety ignition key and reconnect spark plug wire to spark plug.

IMPELLER SHEAR BOLTS

 

The impeller is secured to the impeller shaft with two (2)

 

capscrew/shear bolts and hex nuts. Should a foreign object

 

or ice become lodged in the impeller, the capscrews are

 

designed to break, preventing damage to any other com-

 

ponents. If impeller does not turn when auger control lever

 

is engaged, check to see if the capscrews have sheared.

16

To replace the capscrew/shear bolts:

4.Insert safety ignition key and reconnect spark plug wire to spark plug.

1/4-20

1/4-20 x 1-5/8

1/4-20 x 2

LOCKNUT

CAPSCREW /

SHOULDER /

 

SHEAR BOLT

SHEAR BOLT

 

IMPELLER HUB

 

 

IMPELLER

 

 

SHAFT

 

 

 

AUGER

 

 

HUB

1/4-20

 

 

LOCKNUT

AUGER HUB

AUGER SHAFT

FIG. 21

TO REMOVE BELT COVER (See Fig. 22)

1.Remove the two (2) screws securing belt cover to frame.

2.Remove belt cover.

3.Replace belt cover by installing cover and screws and tighten securely.

BELT

COVER

FRAME

SCREWS

FIG. 22

Image 16
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerParts Packed Separately in Carton Remove Snow Thrower from CartonInstall Traction Drive Control ROD See Figs Install Speed Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotater Head See FigInstall Chute Deflector Remote Control See Figs Check Tire PressureOperation Know Your Snow ThrowerPrimer Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineHOW to USE Your Snow Thrower StoppingUsing the CLEAN-OUT Tool See Fig Power Steering Operation See FigTo Adjust Skid Plates See Fig To Move Forward and Backward See FigBefore Starting the Engine Scraper BAR See FigTo USE Drift Cutters See Fig Check Engine OIL Level See FigSnow Throwing Tips To Start EngineBefore Stopping If Recoil Starter has FrozenMaintenance General RecommendationsBefore Each USE LubricationCleaning EngineService and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See FigTo Replace Belts See Fig To Adjust Cable Tension See Fig To Remove Wheels See FigCarburetor Engine SpeedStorage OtherFuel System Engine OILTroubleshooting KEY Part Description 23 22 Gearbox Assembly 178675X008 Corner Bracket Clean OUT ToolBearing Impeller PulleyAuger Assembly 30 LH Auger Assembly 30 RHWeight BAR Drift Cutter BARCARRIAGEBOLT5/16−18X.750 Plastic WasherDeflector Spring 15 420679 Service Part Deflector Control Knob BlackPOP Rivet Chute Snow ShieldLEVER/CABLE Rotator Assembly Cable Assembly AdjustableRotator Head Rotator Pivot BracketLoop Handle LH Loop Handle RHLower Tube Pivot SupportImpeller ROD Assembly Traction ROD AssemblyShifter ROD TOP Shifter ROD BottomWire Harness Panel ConsoleHeadlight Bezel Halogen HeadlightRepair Parts Snow Thrower - Model Number PR1330ES Drive Exploded Assembly Drive Plate AssemblySpeed Selector Rubber RingComplete LCT Engine Frame427963X428 Engine Mounting PlateImpeller Belt Traction BeltIdler ARM Bracket Idler PulleyCable Bracket LH Wheel Assembly LHCable Bracket RH Cover Wheel Driver Retainer RingWheel Lobe Clutch SlideSafety Ignition KEY 422663DECAL, Danger 181037DECAL, DANGER, Deflector Limited Warranty

96192003201, 429896 specifications

The Poulan 429896,96192003201 is a high-performance chainsaw designed for both professional and residential use. This versatile tool is particularly favored for its robust features that enhance efficiency and ease of use.

One of the standout characteristics of the Poulan 429896 is its powerful engine. Equipped with a high-performance 42cc engine, this chainsaw provides ample power for cutting through tough wood and dense materials with ease. The engine is designed to deliver optimal torque and power, allowing users to complete tasks quickly without compromising on performance.

The chainsaw features a 16-inch bar and chain, ideal for a wide range of cutting applications. This size strikes a perfect balance between maneuverability and cutting capacity, making it suitable for trimming branches, felling small trees, and performing maintenance tasks around the yard. The bar and chain are designed for durability and long life, ensuring that the saw remains operational through extensive use.

One of the most valuable technologies integrated into the Poulan 429896 is the Easy Start feature. This function minimizes the effort required to start the engine, making it accessible for users of various skill levels. Whether you are a seasoned professional or a weekend warrior, the Easy Start technology ensures a hassle-free experience.

In terms of safety, the Poulan 429896 incorporates several features that enhance user protection. The chainsaw is equipped with a chain brake that engages automatically in the event of kickback, an essential safety feature that helps prevent accidents. Additionally, the ergonomic design of the handle provides a comfortable grip while minimizing vibrations, allowing for longer periods of use without discomfort.

Maintenance is also a key consideration with the Poulan 429896. The chainsaw is designed for easy access to the air filter and spark plug, making routine maintenance tasks more straightforward. This user-friendly design ensures that the chainsaw remains in peak condition for years to come.

Overall, the Poulan 429896,96192003201 stands out for its combination of power, efficiency, and safety. Whether you are tackling heavy-duty landscaping projects or light pruning, this chainsaw offers the reliability and performance needed to get the job done effectively. With its durable construction and user-friendly features, the Poulan 429896 is an excellent choice for anyone in need of a dependable chainsaw.