Poulan 428556 Snow Throwing Tips, To Start Engine, Before Stopping, If Recoil Starter has Frozen

Page 13

OPERATION

TO START ENGINE

Be sure fuel shut-off valve is in the “OPEN” position.

Your snow thrower engine is equipped with both a 120 Volt A.C. electric starter and a recoil starter. The electric starter is equipped with a three-wire power cord and plug and is designed to operate on 120 Volt A.C. household current.

Be sure your house is a 120 Volt A.C. three-wire grounded system. If you are uncertain, consult a licensed electrician.

WARNING: Do not use the electric starter if your house is not a 120 Volt A.C. three-wire grounded system. Seri- ous personal injury or damage to your snow thrower could result.

COLD START - ELECTRIC STARTER

1.Insert safety ignition key (tied to recoil start cord) into ignition slot until it clicks. DO NOT turn the key. Keep the extra safety ignition key in a safe place.

2.Place ON / OFF switch in “ON” position.

3.Move choke control to “FULL” position.

4.Connect the power cord to the engine.

5.Plug the other end of the power cord into a three-hole grounded 120 Volt A.C. receptacle.

NOTE: Do not use primer when starting engine with the electric starter.

6. Push starter button until engine starts.

IMPORTANT: Do not crank engine more than five continu- ous seconds between each time you try to start. Wait 5 to 10 seconds between each attempt.

7.When the engine starts, release the starter button and slowly move the choke control to the “OFF” position.

8.Disconnect the power cord from the receptacle first, then from the engine.

Allow the engine to warm up for a few minutes. Engine will not develop full power until it has reached normal operat- ing temperature.

WARM START - ELECTRIC STARTER

Follow the steps above, keeping the choke control in the “OFF” position.

COLD START - RECOIL STARTER

1.Insert safety ignition key (tied to recoil start cord) into ignition slot until it clicks. DO NOT turn the key. Keep the extra safety ignition key in a safe place.

2.Place ON / OFF switch in “ON” position.

3.Rotate choke control to “FULL” position.

4.Push the primer four (4) times if the temperature is below 15°F, or two (2) times if temperature is between 15° and 50°F. If temperature is above 50°F, priming is not necessary.

NOTE: Over priming may cause flooding, preventing the engine from starting. If you do flood the engine, wait a few minutes before attempting to start and DO NOT push the primer.

5.Pull recoil starter handle quickly. Do not allow starter rope to snap back.

6.When the engine starts, release the recoil starter handle and slowly move the choke control to the “OFF” posi- tion.

Allow the engine to warm up for a few minutes. Engine will not develop full power until it has reached normal operat- ing temperature.

WARM START - RECOIL STARTER

Follow the steps above, keeping the choke in the “OFF” position. DO NOT push the primer.

BEFORE STOPPING

Run the engine for a few minutes to help dry off any mois- ture on the engine.

IF RECOIL STARTER HAS FROZEN

If the recoil starter has frozen and will not turn the engine, proceed as follows:

1.Grasp the recoil starter handle and slowly pull as much rope out of the starter as possible.

2.Release the recoil starter handle and let it snap back against the starter.

If the engine still fails to start, repeat the above steps or use the electric starter.

SNOW THROWING TIPS

Go slower in deep, freezing or heavy wet snow. Use the drive speed control, NOT the ON / OFF switch, to adjust speed.

It is easier and more efficient to remove snow imme- diately after it falls.

The best time to remove snow is the early morning. At this time the snow is usually dry and has not been ex- posed to the direct sun and warming temperatures.

Slightly overlap each successive path to ensure all snow will be removed.

Throw snow downwind whenever possible.

Adjust the skid plates to proper height for current snow conditions. See “TO ADJUST SKID PLATES” in this section of this manual.

For extremely heavy snow, reduce the width of snow removal by overlapping previous path and moving slowly.

Keep engine clean and clear of snow during use. This will help air flow and extend engine life.

After snow-throwing is completed, allow engine to run for a few minutes to melt snow and ice off the engine.

Clean the entire snow thrower thoroughly after each use and wipe dry so it is ready for next use.

WARNING: Do not operate snow thrower if weather conditions impair visibility. Throwing snow during a heavy, windy snowstorm can blind you and be hazardous to the safe operation of the snow thrower.

13

Image 13
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONRemove Snow Thrower from Carton Unfold Upper HandleInstall Auger Control ROD See Figs Install Traction Drive Control ROD See FigsInstall Chute Deflector Remote Control See Figs Install Discharge Chute / Chute Rotater Head See FigCheck Tire Pressure Know Your Snow Thrower OperationPrimer Ignition KEYRecoil auxiliary starter handle used for starting engine Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerPower Steering Operation See Fig Using the CLEAN-OUT Tool See FigTo Move Forward and Backward See Fig Before Starting the Engine To Adjust Skid Plates See FigScraper BAR See Fig Check Engine OIL Level See FigTo Start Engine Snow Throwing TipsBefore Stopping If Recoil Starter has FrozenGeneral Recommendations MaintenanceBefore Each USE LubricationSnow Thrower CleaningEngine To Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See FigTo Replace Belts See Fig To Remove Wheels See Fig To Adjust Cable Tension See FigCarburetor Engine SpeedOther StorageFuel System Engine OILTroubleshooting Auger Assembly 30 LH Auger HousingAuger Assembly 30 RH KEY Part Description23 22 178675X008 Corner Bracket Clean OUT Tool Gearbox AssemblyBearing Impeller PulleyBearing Plug Auger BearingChute Weldment Deflector Control AssemblyDeflector Weldment Deflector SealCable Assembly Adjustable LEVER/CABLE Rotator AssemblyRotator Head Rotator Pivot BracketRepair Parts Snow Thrower Model PR1030ES Handles Spacer Repair Parts HandlesKnob RED Handle KnobTraction ROD Impeller RODShifter ROD TOP Shifter ROD BottomLower Tube Wire HarnessPivot Support Console PanelAxle Shaft Repair Parts Snow Thrower Model PR1030ES DriveSprocket Repair Parts Snow Thrower Model PR1030ES 96192003100DRIVE Drive Plate Assembly AssemblySpeed Selector Rubber RingComplete LCT Engine Cover AssemblyFrame 427963X428Traction Belt Impeller BeltIdler ARM Bracket Idler PulleyRepair Parts Snow Thrower Model PR1030ES Wheels Cable Bracket RH Cable Bracket LHSafety Ignition KEY Repair Parts Snow Thrower Model PR1030ES BAG of Parts422663 181037 Repair Parts Snow Thrower Model PR1030ES DecalsDECAL, Danger DECAL, DANGER, DeflectorHOP Limited Warranty