Poulan 428556 owner manual Meets A.N.S.I. Safety Requirements

Page 9

OPERATION

MUFFLER

GASOLINE

FILLER CAP

CHOKE

CON-

TROL

SAFETY

IGNITION

KEY

ON / OFF

SWITCH

PRIMER

FUEL SHUT-OFF VALVE

RECOIL (AUXILIARY) STARTER HANDLE

NOTE: ITEMS ABOVE

ARE SHOWN IN

THEIR TYPICAL

LOCATION ON THE

ENGINE. ACTUAL

LOCATION MAY VARY

WITH THE ENGINE

ON YOUR UNIT.

AUGERS

ELECTRIC	AUGER		DISCHARGE CHUTE CONTROL LEVER
START	CONTROL
BUTTON	LEVER	DRIVE SPEED		DEFLECTOR	TRACTION
		DRIVE SPEED		REMOTE	DRIVE
		CONTROL LEVER		REMOTE	DRIVE
POWER		CONTROL LEVER		CONTROL	CONTROL
POWER				CONTROL	CONTROL
CORD				LEVER	LEVER
PLUG
	CHUTE
DEFLECTOR

LH TURN

TRIGGER

DISCHARGE

CHUTE

		LIGHT
	CLEAN-OUT TOOL	HANDLE
	CLEAN-OUT TOOL	KNOB
		KNOB
		MUFFLER
		TOOLBOX

SKID PLATE

FIG. 10

MEETS A.N.S.I. SAFETY REQUIREMENTS

Our snow throwers conform to the standards of the American National Standards Institute.

Toolbox - used to store spare shear bolts, locknuts and wrench.

Safety ignition key - must be inserted for the engine to start and run. Remove when snow thrower is not in use.

Electric start button - used for starting the engine.

Recoil (auxiliary) starter handle - used for starting engine.

Primer - pumps additional fuel from the carburetor to the cylinder for use when starting a cold engine.

Choke Control - used for starting a cold engine. ON / OFF switch - used to STOP the engine.

LH and RH turn triggers - used to steer the snow thrower.

Drive speed control lever - used to select forward or reverse motion and speed of snow thrower.

Traction drive control lever - used to engage power-pro- pelled forward or reverse motion of snow thrower.

Auger control lever - used to engage auger motion (throw snow).

Discharge chute control lever - used to change the di- rection the snow is thrown.

Deflector remote control lever - used to change the distance the snow is thrown.

Skid plate - used to adjust height of scraper bar from the ground.

9

Image 9

Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONRemove Snow Thrower from Carton Unfold Upper HandleInstall Auger Control ROD See Figs Install Traction Drive Control ROD See FigsInstall Discharge Chute / Chute Rotater Head See Fig Install Chute Deflector Remote Control See FigsCheck Tire Pressure Know Your Snow Thrower OperationPrimer Ignition KEYRecoil auxiliary starter handle used for starting engine Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerUsing the CLEAN-OUT Tool See Fig Power Steering Operation See FigTo Move Forward and Backward See Fig Before Starting the Engine To Adjust Skid Plates See FigScraper BAR See Fig Check Engine OIL Level See FigTo Start Engine Snow Throwing TipsBefore Stopping If Recoil Starter has FrozenGeneral Recommendations MaintenanceBefore Each USE LubricationCleaning Snow ThrowerEngine To Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See FigTo Replace Belts See Fig To Remove Wheels See Fig To Adjust Cable Tension See FigCarburetor Engine SpeedOther StorageFuel System Engine OILTroubleshooting Auger Assembly 30 LH Auger HousingAuger Assembly 30 RH KEY Part Description23 22 178675X008 Corner Bracket Clean OUT Tool Gearbox AssemblyBearing Impeller PulleyBearing Plug Auger BearingChute Weldment Deflector Control AssemblyDeflector Weldment Deflector SealCable Assembly Adjustable LEVER/CABLE Rotator AssemblyRotator Head Rotator Pivot BracketRepair Parts Snow Thrower Model PR1030ES Handles Spacer Repair Parts HandlesKnob RED Handle KnobTraction ROD Impeller RODShifter ROD TOP Shifter ROD BottomLower Tube Wire HarnessPivot Support Console PanelRepair Parts Snow Thrower Model PR1030ES Drive Axle ShaftSprocket Repair Parts Snow Thrower Model PR1030ES 96192003100DRIVE Drive Plate Assembly AssemblySpeed Selector Rubber RingComplete LCT Engine Cover AssemblyFrame 427963X428Traction Belt Impeller BeltIdler ARM Bracket Idler PulleyRepair Parts Snow Thrower Model PR1030ES Wheels Cable Bracket RH Cable Bracket LHRepair Parts Snow Thrower Model PR1030ES BAG of Parts Safety Ignition KEY422663 181037 Repair Parts Snow Thrower Model PR1030ES DecalsDECAL, Danger DECAL, DANGER, DeflectorHOP Limited Warranty