Poulan 428556 owner manual Storage, Other, Fuel System, Engine OIL, Cylinder

Page 19

STORAGE

Immediately prepare your snow thrower for storage at the end of the season or if the unit will not be used for 30 days or more.

WARNING: Never store the snow thrower with gasoline in the tank inside a building where fumes may reach an open flame, spark or pilot light as on a furnace, water heater, clothes dryer or gas appliance. Allow the engine to cool before storing in any enclosure.

SNOW THROWER

When snow thrower is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in a clean, dry area.

1.Clean entire snow thrower (See “CLEANING” in the Maintenance section of this manual).

2.Inspect and replace belts, if necessary (See “TO RE- PLACE BELTS” in the Service and Adjustments section of this manual).

3.Lubricate as shown in the Maintenance section of this manual.

4.Be sure that all nuts, bolts, screws, and pins are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary.

5.Touch up all rusted or chipped paint surfaces; sand lightly before painting.

ENGINE

See engine manual.

FUEL SYSTEM

IMPORTANT: It is important to prevent gum deposits from forming in essential fuel system parts such as carburetor, fuel hose, or tank during storage. Also, alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage.

Empty the fuel tank by starting the engine and letting it run until the fuel lines and carburetor are empty.

Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable alternative in min- imizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the carburetor. Do not drain the gas tank and carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean engine oil. (See “ENGINE” in the Maintenance section of this manual).

CYLINDER

1.Remove spark plug.

2.Pour one ounce (29 ml) of oil through spark plug hole into cylinder.

3.Pull recoil starter handle slowly a few times to distribute oil.

4.Replace with new spark plug.

OTHER

Remove safety ignition key; store it in a safe place.

Do not store gasoline from one season to another.

Replace your gasoline can if your can starts to rust. Rust and/or dirt in your gasoline will cause problems.

If possible, store your snow thrower indoors and cover it to protect it from dust and dirt.

Cover your snow thrower with a suitable protective cover that does not retain moisture. Do not use plastic. Plastic cannot breathe, which allows condensation to form and will cause your snow thrower to rust.

IMPORTANT: Never cover snow thrower while engine/ex- haust area is still warm.

19

Image 19
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Unfold Upper Handle Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from CartonInstall Auger Control ROD See Figs Install Traction Drive Control ROD See FigsInstall Chute Deflector Remote Control See Figs Install Discharge Chute / Chute Rotater Head See FigCheck Tire Pressure Ignition KEY OperationKnow Your Snow Thrower PrimerRecoil auxiliary starter handle used for starting engine Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerPower Steering Operation See Fig Using the CLEAN-OUT Tool See FigTo Move Forward and Backward See Fig Check Engine OIL Level See Fig To Adjust Skid Plates See FigBefore Starting the Engine Scraper BAR See FigIf Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before StoppingLubrication MaintenanceGeneral Recommendations Before Each USESnow Thrower CleaningEngine Shear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Replace Belts See Fig Engine Speed To Adjust Cable Tension See FigTo Remove Wheels See Fig CarburetorEngine OIL StorageOther Fuel SystemTroubleshooting KEY Part Description Auger HousingAuger Assembly 30 LH Auger Assembly 30 RH23 22 Impeller Pulley Gearbox Assembly178675X008 Corner Bracket Clean OUT Tool BearingBearing Plug Auger BearingDeflector Seal Deflector Control AssemblyChute Weldment Deflector WeldmentRotator Pivot Bracket LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Rotator HeadRepair Parts Snow Thrower Model PR1030ES Handles Handle Knob Repair Parts HandlesSpacer Knob REDShifter ROD Bottom Impeller RODTraction ROD Shifter ROD TOPConsole Panel Wire HarnessLower Tube Pivot SupportAxle Shaft Repair Parts Snow Thrower Model PR1030ES DriveSprocket Repair Parts Snow Thrower Model PR1030ES 96192003100DRIVE Rubber Ring AssemblyDrive Plate Assembly Speed Selector427963X428 Cover AssemblyComplete LCT Engine FrameIdler Pulley Impeller BeltTraction Belt Idler ARM BracketRepair Parts Snow Thrower Model PR1030ES Wheels Cable Bracket RH Cable Bracket LHSafety Ignition KEY Repair Parts Snow Thrower Model PR1030ES BAG of Parts422663 DECAL, DANGER, Deflector Repair Parts Snow Thrower Model PR1030ES Decals181037 DECAL, DangerHOP Limited Warranty