MTD 140, E162, E150, E172 Operating Your Snow Thrower, Fuel And Oil Mixture, Starting the Engine

Page 8

Discharge Chute

The pitch of the discharge chute controls the angle at which the snow is thrown. Loosen the wing knob on the side of the discharge chute before pivoting the discharge chute upward or downward. Retighten the knob once the desired position has been achieved.

Shave Plate

The shave plate scrapes along the pavement as the snow thrower is propelled, allowing the snow close to the pavement’s surface to be discharged.

SECTION 4: OPERATING YOUR SNOW THROWER

WARNING: Before starting the engine, read, understand, and follow all instructions and warnings on the machine and in this manual before operating.

Fuel And Oil Mixture

WARNING: Use extreme care when handling gasoline. Gasoline is extremely flammable and the vapors are explosive. Never fuel machine indoors or while the engine is hot or running. Extinguish cigarettes, cigars, pipes and other sources of ignition.

Your snow thrower is equipped with a two-cycle engine that requires a mixture of gasoline and two cycle engine oil at a ratio of 50:1. Refer to the Tecumseh Engines operator’s manual for detailed instructions regarding oil and gasoline for your snow thrower’s engine.

•A plastic cup is placed inside the fuel fill opening on the fuel tank (beneath the fuel cap) to keep debris out during product assembly. Remove and discard this cup before filling up the tank.

IMPORTANT: Do NOT operate the snow thrower without the fuel cap securely in place on the fuel tank.

Starting the Engine

•Refer to the Tecumseh Engines manual packed with the snow thrower for detailed instructions regarding starting the engine.

Operating the Snow Thrower

•Loosen the wing knob found on the left side of the discharge chute and pivot the upper chute upward or downward to the desired pitch. Retighten the wing knob before operating the snow thrower.

•Crank the chute directional control to position the discharge chute opening in the desired direction. See Figure 7.

NOTE: For more efficient snow clearing, discharge snow downwind whenever possible.

Control Handle

Chute

Directional Control

Figure 7

WARNING: Never operate the snow thrower with bystanders in front of or near the discharge chute opening.

•Engage the auger by squeezing the control handle against the upper handle. See Figure 7.

•Lift up slightly on the handle to allow the rubber paddles on the auger to contact the pavement and propel the snow thrower forward.

IMPORTANT: Excessive upward pressure on the handle will result in premature wear on the rubber auger paddles. Resulting wear would not be covered by warranty.

•As the snow thrower starts to move, maintain a firm hold on the handle, and guide the snow thrower along the path to be cleared.

•Release the auger control handle to stop the snow throwing action and the forward motion.

Stopping the Engine

WARNING: Muffler, engine and surrounding areas become hot and can cause a burn. Do not touch.

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents OPERATOR’S Manual Table of Contents Important Safe Operation Practices TrainingPreparation OperationMaintenance And Storage Your ResponsibilityContents of Carton Assembling Your Snow ThrowerPositioning the Upper Handle Attaching the Control CableInstalling the Extended Chute Assembling the Discharge ChuteEye Bolt on models so equipped Directional Control on models so equippedKnow Your Snow Thrower Stopping EngineOperating Your Snow Thrower Fuel And Oil MixtureStarting the Engine Operating the Snow ThrowerMaking Adjustments Control Cable & Belt TensionMaintaining Your Snow Thrower Replacing the Shave Plate Replacing the Auger’s Rubber PaddlesTroubleshooting Guide Accessories & KitsPage Parts List Models 140, 150, E150, E162 & E172 Models 140, 150, E150, E162 & E172 Models 140, 150, E150, E162 & E172 Índice Sección 1 Medidas Importantes DE Seguridad CapacitaciónPreparativos FuncionamientoMantenimiento y almacenamiento Su responsabilidadSección 2 Montaje DE LA Máquina Quitanieve Contenido de la cajaColocación de la manija superior Colocación del cable de controlMontaje del canal de descarga Instalación del canal extendido Control direccionalEnchufe del arrancador eléctrico Palanca de obturaciónCebador Llave de encendidoDetención del motor Mezcla de combustible y aceiteEncendido del motor Sección 5 Realización DE Ajustes Placa de raspadoSección 6 Mantenimiento DE LA Máquina Quitanieve Sección 8 Guía Para LA Solución DE Problemas Sección 7 Almacenamiento Fuera DE TemporadaPage Notas Notas DEL Fabricante Garantía Limitada MANUFACTURER’S Limited Warranty

150, 140, E172, E150, E162 specifications

The MTD E150, E162, E172, 150, and 140 represent a range of compact and efficient outdoor power equipment designed for both residential and commercial use. Tailored to meet diverse landscaping needs, these models offer a blend of advanced technology, user-friendly features, and robust performance.

Starting with the MTD E150, this model is known for its lightweight design, making it easy to maneuver in tight spaces. It features a powerful electric motor that ensures a quiet operation while delivering sufficient torque for various lawn care tasks. The E150 also incorporates a versatile cutting system, allowing users to adjust the cutting height easily to achieve the preferred grass length.

Moving on to the MTD E162, this model is an upgrade in terms of power and capability. It boasts an enhanced battery life with quick charging options, providing extended use for larger yards. The E162 is equipped with a more advanced cutting deck that not only improves grass collection but also minimizes clumping, ensuring a neat finish. Additionally, it integrates smart technology that enables users to monitor battery status and operational parameters through a dedicated mobile app.

The MTD E172 takes it a step further with robust features designed for residential and commercial users. This model includes self-propelled mechanisms for effortless operation on uneven terrain. Its exceptional cutting width improves efficiency, allowing for fewer passes over large areas. The E172 also offers multiple speed settings, making it adaptable to various landscaping tasks.

The traditional MTD 150 and 140 models continue to be popular choices for users who prefer gas-powered equipment. The MTD 150 is recognized for its high-torque engine that delivers impressive cutting power. Its fuel efficiency reduces the frequency of refueling, allowing for longer operation times with minimal interruptions. The ergonomic design of the 150 enhances user comfort, featuring adjustable handles and a snug grip.

The MTD 140, while being the more compact choice, does not compromise on performance. It caters well to smaller yards with its efficient cutting technology that thoroughly gathers clippings while reducing the overall cutting time. Its lightweight structure facilitates easy lift and storage.

In summary, the MTD E150, E162, E172, 150, and 140 models showcase the brand’s commitment to innovation and performance in outdoor power equipment. With a strong focus on user experience, these models feature advanced technologies designed to provide efficient, reliable, and enjoyable lawn care solutions for everyone.
Top Page Image Contents