MTD E162, E150, E172, 140 manual Making Adjustments, Control Cable & Belt Tension

Page 9

•After clearing snow, allow the engine to run for an extra few minutes before storing to help dry any moisture on the engine.

•To stop the engine: Turn the ignition key counterclockwise to the OFF position. Refer to Ignition Key on page 7. Remove the key form the snow thrower’s ignition switch before storing.

IMPORTANT: Keep the ignition key in a safe place. The engine can not be started without it.

•Wipe all the snow and any moisture which has formed, from the unit.

•Move the choke lever back and forth several times.

SECTION 5: MAKING ADJUSTMENTS

WARNING: NEVER attempt to make any adjustments while the engine is running, except where specified in the operator’s manual.

Control Cable & Belt Tension

As a result of both the control cable and the drive belt stretching due to wear, periodic adjustments may be necessary.

If the auger seems to hesitate when rotating while the engine maintains a constant speed, an adjustment is necessary. Proceed as follows:

The upper hole in the control handle provides for an adjustment in cable tension. To adjust, disconnect the end of control cable from the bottom hole in the control handle and reinsert it in the upper hole. Refer to Figure 3 . Test the snow thrower to see if there is a noticeable difference.

If additional adjustment is required, proceed as follows.

•Remove the belt cover from the left side of the snow thrower’s auger housing by unthreading the

five hex screws which secure it in place. See Figure 8.

There are three adjustment holes provided in the idler bracket assembly. To adjust, proceed as follows:

•Move the extension spring (found on the end of the control cable) from the low position to the middle position on the idler bracket. See Figure 9.

NOTE: Be careful not to lose the idler spring when moving the clutch cable spring. See Figure 9.

•If the extension spring is already found in the middle position on the idler bracket, move it from the middle position to the high position.

•Reattach the belt cover with the five hex screws removed earlier.

Hex Screws

Belt Cover

Figure 8

Idler Spring

Control Cable

Idler Bracket

Spring

Adjustment

 

Holes

 

Figure 9

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents OPERATOR’S Manual Table of Contents Training Important Safe Operation PracticesPreparation OperationYour Responsibility Maintenance And StorageAssembling Your Snow Thrower Contents of CartonPositioning the Upper Handle Attaching the Control CableAssembling the Discharge Chute Installing the Extended ChuteEye Bolt on models so equipped Directional Control on models so equippedStopping Engine Know Your Snow ThrowerFuel And Oil Mixture Operating Your Snow ThrowerStarting the Engine Operating the Snow ThrowerControl Cable & Belt Tension Making AdjustmentsMaintaining Your Snow Thrower Replacing the Auger’s Rubber Paddles Replacing the Shave PlateAccessories & Kits Troubleshooting GuidePage Parts List Models 140, 150, E150, E162 & E172 Models 140, 150, E150, E162 & E172 Models 140, 150, E150, E162 & E172 Índice Capacitación Sección 1 Medidas Importantes DE SeguridadPreparativos FuncionamientoSu responsabilidad Mantenimiento y almacenamientoContenido de la caja Sección 2 Montaje DE LA Máquina QuitanieveColocación de la manija superior Colocación del cable de controlInstalación del canal extendido Control direccional Montaje del canal de descargaPalanca de obturación Enchufe del arrancador eléctricoCebador Llave de encendidoMezcla de combustible y aceite Encendido del motorDetención del motor Placa de raspado Sección 5 Realización DE AjustesSección 6 Mantenimiento DE LA Máquina Quitanieve Sección 7 Almacenamiento Fuera DE Temporada Sección 8 Guía Para LA Solución DE ProblemasPage Notas Notas DEL Fabricante Garantía Limitada MANUFACTURER’S Limited Warranty

150, 140, E172, E150, E162 specifications

The MTD E150, E162, E172, 150, and 140 represent a range of compact and efficient outdoor power equipment designed for both residential and commercial use. Tailored to meet diverse landscaping needs, these models offer a blend of advanced technology, user-friendly features, and robust performance.

Starting with the MTD E150, this model is known for its lightweight design, making it easy to maneuver in tight spaces. It features a powerful electric motor that ensures a quiet operation while delivering sufficient torque for various lawn care tasks. The E150 also incorporates a versatile cutting system, allowing users to adjust the cutting height easily to achieve the preferred grass length.

Moving on to the MTD E162, this model is an upgrade in terms of power and capability. It boasts an enhanced battery life with quick charging options, providing extended use for larger yards. The E162 is equipped with a more advanced cutting deck that not only improves grass collection but also minimizes clumping, ensuring a neat finish. Additionally, it integrates smart technology that enables users to monitor battery status and operational parameters through a dedicated mobile app.

The MTD E172 takes it a step further with robust features designed for residential and commercial users. This model includes self-propelled mechanisms for effortless operation on uneven terrain. Its exceptional cutting width improves efficiency, allowing for fewer passes over large areas. The E172 also offers multiple speed settings, making it adaptable to various landscaping tasks.

The traditional MTD 150 and 140 models continue to be popular choices for users who prefer gas-powered equipment. The MTD 150 is recognized for its high-torque engine that delivers impressive cutting power. Its fuel efficiency reduces the frequency of refueling, allowing for longer operation times with minimal interruptions. The ergonomic design of the 150 enhances user comfort, featuring adjustable handles and a snug grip.

The MTD 140, while being the more compact choice, does not compromise on performance. It caters well to smaller yards with its efficient cutting technology that thoroughly gathers clippings while reducing the overall cutting time. Its lightweight structure facilitates easy lift and storage.

In summary, the MTD E150, E162, E172, 150, and 140 models showcase the brand’s commitment to innovation and performance in outdoor power equipment. With a strong focus on user experience, these models feature advanced technologies designed to provide efficient, reliable, and enjoyable lawn care solutions for everyone.
Top Page Image Contents