MTD D Style, C Style warranty Off-Season Storage, Preparing Engine, Preparing Snow Thrower

Page 18

7

Off-Season

Storage

WARNING

Never store snow thrower with fuel in tank indoors or in poorly ventilated areas, where fuel fumes may reach an open flame, spark or pilot light as on a furnace, water heater, clothes dryer or gas appliance.

Drain fuel into an approved container outdoors, away from any open flame. Be certain engine is cool. Do not smoke. Fuel left in engine during warm weather deteriorates and will cause serious starting problems.

Do not drain carburetor if using fuel stabilizer. Never use engine or carburetor cleaning products in the fuel tank or permanent damage may occur.

If the snow thrower will not be used for 30 days or longer, or if it is the end of the snow season when the last pos- sibility of snow is gone, the equipment needs to be stored properly. Follow storage instructions below to ensure top performance from the snow thrower for many more years.

Preparing Engine

WARNING: Never store snow thrower with fuel in tank indoors or in poorly ventilated areas, where fuel fumes may reach an open flame, spark or pilot light as on a furnace, water heater, clothes dryer or gas appliance.

NOTE: It is important to prevent gum deposits from form- ing in essential fuel system parts of the engine such as the carburetor, fuel filter, fuel hose or tank during storage.

CAUTION: Alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage.

To avoid engine problems, the fuel system should be emptied before storage for 30 days or longer. Follow these instructions to prepare your snow thrower for storage:

WARNING: Drain fuel into an ap- proved container outdoors, away from any open flame. Be certain engine is cool. Do not smoke.

Fuel left in engine during warm weather deteriorates and will cause serious starting problems.

1.Remove all gasoline from the carburetor and the fuel tank to prevent gum deposits from forming on these parts and harming the engine.

2.Run the engine until the fuel tank is empty and it stops due to lack of fuel.

3.Drain carburetor by pressing upward on bowl drain, located below the carburetor cover (refer to the Tecumseh engine manual for more detailed instruc- tion).

WARNING: Do not drain carbure- tor if using fuel stabilizer. Never use engine or carburetor cleaning products in the fuel tank or permanent damage may occur.

NOTE: Fuel stabilizer (such as STA-BIL) is an accept- able alternative in minimizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow it to reach the carburetor. Do not drain carburetor if using fuel stabilizer.

4.Remove the spark plug and pour one (1) ounce of engine oil through the spark plug hole into the cylinder. Cover spark plug hole with a rag and crank the engine several times to distribute the oil. Replace spark plug.

NOTE: Refer to the Tecumseh engine manual for more information on preparing the snow thrower engine for storage.

Preparing Snow Thrower

1.When storing the snow thrower in an unventilated or metal storage shed, care should be taken to rustproof the equipment. Using a light oil or silicone, coat the equipment, especially any chains, springs, bearings and cables.

2.Remove all dirt from exterior of engine and equipment.

3.Follow lubrication recommendations on page 12.

4.Store equipment in a clean, dry area.

18

Image 18
Contents Form no -01274C Two-Stage Snow Thrower C, D StyleMTD LLC, P.O. BOX 361131 CLEVELAND, Ohio 06/08/2005Table of Contents Finding and Recording Model NumberCustomer Support Chute clean-out tool is fastened to the top Your ResponsibilityTrainingPreparation Your Responsibility Restrict the useDo not modify engine Maintenance & StorageOperation Your ResponsibilitySetting Up Your Snow Thrower Position the chute assembly over the baseTire Pressure Remove the flat washer and hairpin clip from the endChute directional control Operating Your Snow Thrower Know Your Snow ThrowerAuger Control Clean-Out ToolChute Assembly Drive ControlIf your home’s Gas & Oil Fill-UpStopping The Engine Electric StarterTo Engage Augers Chute Clean-Out ToolTo Engage Drive Recoil StarterMaking Adjustments Retightening the nuts Chute Bracket AdjustmentTo adjust the skid shoes Surrounding propertyLubrication Maintaining Your Snow ThrowerEngine Shave Plate and Skid Shoes Auger Belt Replacement Drive Belt Replacement Friction Wheel Removal That it rests on the auger housingAssembly off the shaft Cracking and replace if necessaryOff-Season Storage Preparing EnginePreparing Snow Thrower Trouble Shooting Problem Cause RemedyStyles C & D To order replacement Parts, contact Or visit Styles C & D 710-0376 Handle Ass’y, Lock LHHandle Ass’y, Lock, RH 710-0604AStyles C & D 684-04154 Disc, Friction Wheel684-04153 712-0413Page Page MANUFACTURER’S Limited Warranty for