MTD E600E manual Maintenance and Storage, Shut OFF Engine Before Unclogging Discharge Chute

Page 4

repairs, adjustments, or inspections. Never place your hand in the discharge or collector openings. Use a stick or wooden broom handle to unclog the discharge opening.

Take all possible precautions when leaving the unit unattended. Disengage the collector/impeller, stop the engine, and remove the key.

When cleaning, repairing, or inspecting, make cer- tain collector/impeller and all moving parts have stopped. Disconnect spark plug wire and keep away from plug to prevent accidental starting.

Do not run engine indoors, except when starting engine and transporting snow thrower in or out of building. Open doors. Exhaust fumes are danger- ous.

Do not clear snow across the face of slopes. Exer- cise extreme caution when changing direction on slopes. Do not attempt to clear steep slopes.

Never operate snow thrower without guards, plates, or other safety protection devices in place.

Never operate snow thrower near glass enclosure, automobiles, window wells, drop off, etc., without proper adjustments of snow thrower discharge angle. Keep children and pets away.

Do not overload machine capacity by attempting to clear snow at too fast a rate.

Never operate the machine at high transport speeds on slippery surfaces. Look behind and use care when backing.

Never direct discharge at bystanders or allow any- one in front of unit.

Disengage power to collector/impeller when trans- porting or not in use.

Use only attachments and accessories approved by the manufacturer of snow thrower (such as wheel weights, counter weights, cabs, etc.).

Never operate the snow thrower without good visi- bility or light. Always be sure of your footing and keep a firm hold on the handles. Walk, never run.

Muffler and engine become hot and can cause a burn. Do not touch.

4.MAINTENANCE AND STORAGE

Check shear bolts, engine mounting bolts, etc., at frequent intervals for proper tightness to be sure equipment is in safe working condition.

Never store the machine with fuel in the fuel tank inside a building where ignition sources are present, such as hot water and space heaters, clothes dryers, and the like. Allow engine to cool before storing in any enclosure.

Always refer to operator's manual instructions for important details if snow thrower is to be stored for an extended period.

Run machine a few minutes after throwing snow to prevent freeze up of collector/impeller.

Check clutch controls periodically to verify they engage and disengage properly and readjust if nec- essary. Refer to operator's manual for adjustment instructions.

WARNING - YOUR RESPONSIBILITY: Restrict the use of this power machine to persons who read, understand and follow the warnings and instructions in this manual and on the machine.

SHUT OFF ENGINE

BEFORE

UNCLOGGING

DISCHARGE CHUTE.

.AWAY CLOTHING AND FEET HANDS, KEEP

-AUGER ROTATING FROM INJURY AVOID

DANGER

WARNING

1.STOP ENGINE BEFORE REMOVING DEBRIS AND SERVICING UNIT.

2.KEEP CLEAR OF IMPELLER WHILE ENGINE IS RUNNING.

3.NEVER DIRECT DISCHARGE AT BYSTANDERS OR WINDOWS OR ALLOW ANYONE IN FRONT OF UNIT.

4.THOROUGHLY INSPECT THE AREA WHERE THE EQUIPMENT IS TO BE USED AND REMOVE ALL DOOR MATS, SLEDS, BOARDS, WIRES AND OTHER FOREIGN OBJECTS.

5.REFER TO OWNERS MANUAL FOR FULL INSTRUCTIONS.

Figure 2

4

Image 4
Contents OPERATOR’S Manual Calling Customer Support Finding Your Model Number4683 Important Safe Operation Practices TrainingPreparation OperationMaintenance and Storage Shut OFF Engine Before Unclogging Discharge ChuteTools Required for Assembly Contents in Carton See FigureLoose Parts & Hardware Pack UnpackingContents of Hardware Pack Attaching the Handle Assembly Hardware a AssemblyAttaching the Control Cables Hardware B Attaching the Chute Directional Control Hardware D Attaching the Chute Assembly Hardware CAttaching the Shift ROD Hardware B Final Adjustments Traction Control and Shift Lever Adjust- mentAdjusting the Skid Shoes Auger ControlOperation Operating ControlsShift Lever Auger ControlSafety Ignition Switch Chute Directional ControlThrottle Control GAS and OIL FILL-UPTo Stop Engine Electric Starter If EquippedTo Engage Drive Adjustments Maintenance Traction Control AdjustmentDrive Wheels Lubrication Chute Directional ControlService Auger Belts Drive BeltChanging Friction Wheel Rubber OFF-SEASON StorageFriction Wheel Plates Bearing Screws RubberHub Trouble Shooting Guide Trouble Possible Causes Corrective ActionGear Assembly Models E600E, E610E, E640F, E660G, and E6C0FBlower Housing 712-0116 Lock Jam Nut 3/8-24 Handle Assembly Part Description Frame Assembly Wheel Assemblies Model Size Engine and V-Belts E600E, E610EE640F, E660G, E6C0F MANUFACTURER’S Limited Warranty for