MTD 769-04179 warranty Attaching the Chute Assembly, Attaching the Shift Rod

Page 7

Figure 3-4

Attaching the Chute Assembly

•Remove locknuts and screws securing one of the flange keepers to the chute assembly. See Figure 3-4.

•Loosen but do not remove the locknuts and screws on the other two flange keepers.

•Slide chute assembly over chute opening, making sure the flange keepers are beneath lip of chute adapter. The notches should engage with the spiral end of the chute crank. See Figure 3-5.

•Secure flange keeper, locknuts and screws previously removed. Tighten all flange keepers and hardware with two 7/16” wrenches. Do not over tighten.

NOTE: If necessary the chute crank support bracket can be adjusted so the spiral on the chute crank fully engages the teeth on the chute assembly. Refer to the Adjustment Section.

Attaching the Shift Rod

•Align the upper and lower shift rods, then slide the shift rod connector down over the end of the lower shift rod. Tap the connector until the lower rod is completely through the connector. See Figure 3-6.

NOTE: If the connector is not properly assembled, the shift rod will pivot and you will not be able to change speeds or direction.

NOTE: If the full range of speeds (forward and reverse) cannot be achieved, refer to the Adjustment Section.

•Normally the cable ties holding the steering cables against the handle are loosely installed on each side of the lower handle at the factory. Pull the cable ties tight to secure. Cut the excess from the ends of cable ties.

•If not already attached, slip the cables that run from the handle panel to the discharge chute into the cable guide. See Figure 3-7.

3

Setting Up

Your Snow

Thrower

Figure 3-5

WARNING

Prior to operating your snow thrower, refer to Auger Control on page 9. Read and follow all instructions carefully and perform all adjustments to verify your unit is operating safely and properly.

Figure 3-6

Figure 3-7

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents 769-04179 Two-Stage Snow Thrower06/25/08 Finding and Recording Model Number Table of ContentsCustomer Support Your Responsibility Restrict the use Safety SymbolsThere are rotating blades inside Do not use the engine’s electric starter in the rainYour Responsibility Safe Operation PracticesTraining PreparationAverage Useful Life Maintenance & StorageOperation Do not modify engineAssembling Handle Setting Up Your Snow ThrowerItems Required For Assembly Loose PartsAttaching the Shift Rod Attaching the Chute AssemblyDrift Cutters If Equipped Lamp WiringClean-Out Tool Final AdjustmentsAuger Check the adjustment of the auger control as followsSkid Shoes Tire Pressure Pneumatic TiresKnow Your Snow Thrower Operating Your Snow Thrower$26% #/.42 To Engage Augers Gas & Oil Fill-UpStopping The Engine To Engage DriveIf possible, remove snow immediately after it falls Always observe safety rules when performing any maintenanceOperating Tips General RecommendationsDrive Control AdjustmentsMaking Shift RodAuger Control Chute AssemblyChute Bracket Adjustment See Figure Adjust skid shoes as followsLubrication Maintaining Your Snow ThrowerReplacing Belts Remove Loosen Auger BeltPulley Slot Drive BeltFriction Wheel Using a 3/4 wrench, hold the hex shaftChanging Friction Wheel Rubber Secure with the cupped washer and hex bolt removed earlierOff-Season Storage Problem Cause Remedy Trouble Shooting05.28.08 WarrantyFor parts and/or accessories refer to customer support on 6919 Adressez-vous au «Service après-vente» Parts List Pièces DétachéesLa page 2 pour ce qui concerne les pièces et/ou accessoires Torque to 21 ft./lbs. maximum 305-342 cc618-04514 Worm Gear Box Ass’y w/ grease fitting Part RÉF Pièce Description Plug into alternator Plug into alternator Lead wire under fuel tankGround wire to engine GroundPage 41, pas de 1/2 po x 36 maillons Part RÉF Pièce Description For parts and/or accessories refer to customer support on Page Com.mtdcanada GarantieGarantie cette de Pas couvre ne limitée garantie CetteDépannage Solution Causes ProblèmeJours, 30 de plus pendant entreposé être doit moteur le Si PropreUse Accompagne qui moteur du d’utilisation notice la dansFrottement de Roue Entretien’essieu de ’entraînement Courroie Tarière la de d’entraînement Courroie Courroies les de RemplacementÉloignez ’enlevez’engrenage LubrificationRoues Vitesse de mentRéglages Vitesses de levier du Tige Des l’entraînement de CommandeRoues Les de Évitez .65C 150F dépasser Général d’ordre Recommandations’utilisation Conseils ToucherFaites Ne ’huile et d’essence PleinsGoulotte la de dégagement de Outil Fonctions 2 à Roues des d’orientation CommandeGoulotte la de Commande Goulotte la de directionSouffleuse la de Commandes Tiques Tarière la de CommandePneuma Bandages pneus des Pression Pas Goulotte la de dégagement de OutilBien passe qu’il ce jusqu’à raccord le sur Tapez Vitesses de levier du tige la de InstallationGoulotte la de Installation «Réglages»Cisaillement de Boulons Goulotte la de manivelle la de MontageGuidon du Montage ’assemblage pour requis ArticlesGaz de émissions les concernant Avis Remisage et EntretienResponsabilité Votre Moyenne utile vie de Durée’essence de Manipulation PréparationFormation VotreMachine la d’utiliser Sécurité de SymbolesMatières des Table Vente-après ServiceVente-après service au d’abord adresser vous sans Modèle de numéro le trouver Pour04179-769 ’UTILISATION Notice

769-04179 specifications

The MTD 769-04179 is a powerful and versatile lawn mower designed to meet the needs of homeowners seeking efficiency, durability, and ease of use in lawn care. This model stands out in the competitive market of outdoor power equipment, equipped with a range of features that enhance performance and user experience.

One of the primary characteristics of the MTD 769-04179 is its robust engine. It boasts a reliable gas-powered engine that delivers impressive torque and cutting power. This engine is designed to handle various lawn conditions, making it suitable for small to moderate-sized yards. The mower’s cutting deck typically measures between 20 to 22 inches, allowing users to cover more area with each pass while maintaining precision cutting.

The MTD 769-04179 also integrates advanced cutting technologies. The mower features a 3-in-1 cutting system that allows users to mulch, bag, or side discharge grass clippings based on their preferences and lawn care needs. This capability not only promotes a healthier lawn but also offers flexibility in managing grass waste. The adjustable cutting height is another key attribute, enabling users to select the ideal grass length for their specific lawn type and conditions.

In terms of user comfort and convenience, the MTD 769-04179 is designed with an ergonomic handle, which reduces strain during extended mowing sessions. The 769-04179 model generally includes easy-to-access controls for the engine start, speed adjustments, and cutting height selection, ensuring a seamless user experience.

Durability is also a prominent feature of this lawn mower. The MTD 769-04179 is constructed with high-quality materials that withstand the rigors of regular lawn maintenance. Its sturdy wheels provide excellent traction and maneuverability across different terrains, making it effective on both flat and uneven surfaces.

Maintenance is simplified in the MTD 769-04179, with user-friendly features that include easy access to the spark plug and air filter. This accessibility encourages regular upkeep, ensuring the mower remains in optimal working condition over time.

Overall, the MTD 769-04179 is a reliable choice for homeowners seeking an efficient and easy-to-handle lawn mower. With its powerful engine, versatile cutting options, and user-friendly design, it offers excellent value for those dedicated to maintaining a healthy and beautiful lawn.
Top Page Image Contents