MTD 769-04179 warranty Auger Control, Chute Assembly, Chute Bracket Adjustment, Retighten the nuts

Page 15

Skid Shoes

The space between the shave plate and the ground can be adjusted by raising or lowering the skid shoes.

For close snow removal, as when using on a smooth concrete or asphalt driveway, place the skid shoes in the low position. Use the middle or high position when the area to be cleared is uneven. When operating on gravel, always put skid shoes in the high position.

See Figure 5-4.

Adjust skid shoes as follows:

1.Loosen, but do not remove, the hex flange locknuts which fasten the skid shoe to the auger housing.

2.Raise or lower the skid shoe to desired position.

3.Retighten the hex nuts loosened earlier.

NOTE: Make certain the bottom surface of skid shoe is flat against the ground to avoid uneven wear.

4. Repeat on the other side of the snow thrower.

Auger Control

Refer to instructions on page 9 to adjust the auger control. Make certain to check for correct adjustment as instructed before operating the snow thrower.

Chute Assembly

The distance snow is thrown can be adjusted by adjusting the angle of the chute assembly. Refer to page 9 for instructions.

The remote chute control cables have been pre-adjusted at the factory. Move the remote chute lever on the control panel back and forward to adjust angle of the chute assembly.

Chute Bracket Adjustment

If the spiral at the bottom of the chute directional control is not fully engaging with the chute assembly, the chute bracket can be adjusted. To do so:

1.Loosen the two nuts which secure the chute bracket and reposition it slightly. See Figure 5-5.

2.Retighten the nuts.

Figure 5-4

Figure 5-5

5

Making

Adjustments

IMPORTANT: It is not recommended that you operate this snow thrower on gravel as loose gravel can be easily picked up and thrown by the auger causing personal injury or damage to the snow thrower.

If for some reason, you have to operate the snow thrower on gravel, keep the skid shoe in the highest position for maximum clearance between the ground and the shave plate.

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Two-Stage Snow Thrower 769-0417906/25/08 Table of Contents Finding and Recording Model NumberCustomer Support Your Responsibility Restrict the use Safety SymbolsThere are rotating blades inside Do not use the engine’s electric starter in the rainYour Responsibility Safe Operation PracticesTraining PreparationAverage Useful Life Maintenance & StorageOperation Do not modify engineAssembling Handle Setting Up Your Snow ThrowerItems Required For Assembly Loose PartsAttaching the Shift Rod Attaching the Chute AssemblyDrift Cutters If Equipped Lamp WiringClean-Out Tool Final AdjustmentsAuger Check the adjustment of the auger control as followsSkid Shoes Tire Pressure Pneumatic TiresKnow Your Snow Thrower Operating Your Snow Thrower$26% #/.42 To Engage Augers Gas & Oil Fill-UpStopping The Engine To Engage DriveIf possible, remove snow immediately after it falls Always observe safety rules when performing any maintenanceOperating Tips General RecommendationsDrive Control AdjustmentsMaking Shift RodAuger Control Chute AssemblyChute Bracket Adjustment See Figure Adjust skid shoes as followsMaintaining Your Snow Thrower LubricationReplacing Belts Remove Loosen Auger BeltPulley Slot Drive BeltFriction Wheel Using a 3/4 wrench, hold the hex shaftChanging Friction Wheel Rubber Secure with the cupped washer and hex bolt removed earlierOff-Season Storage Problem Cause Remedy Trouble Shooting05.28.08 WarrantyFor parts and/or accessories refer to customer support on 6919 Parts List Pièces Détachées Adressez-vous au «Service après-vente»La page 2 pour ce qui concerne les pièces et/ou accessoires Torque to 21 ft./lbs. maximum 305-342 cc618-04514 Worm Gear Box Ass’y w/ grease fitting Part RÉF Pièce Description Plug into alternator Plug into alternator Lead wire under fuel tankGround wire to engine GroundPage 41, pas de 1/2 po x 36 maillons Part RÉF Pièce Description For parts and/or accessories refer to customer support on Page Com.mtdcanada GarantieGarantie cette de Pas couvre ne limitée garantie CetteDépannage Solution Causes ProblèmeJours, 30 de plus pendant entreposé être doit moteur le Si PropreUse Accompagne qui moteur du d’utilisation notice la dansEntretien Frottement de Roue’essieu de ’entraînement Courroie Tarière la de d’entraînement Courroie Courroies les de RemplacementÉloignez ’enlevez’engrenage LubrificationRoues Vitesse de mentRéglages Des l’entraînement de Commande Vitesses de levier du TigeRoues Les de Évitez .65C 150F dépasser Général d’ordre Recommandations’utilisation Conseils Toucher’huile et d’essence Pleins Faites NeGoulotte la de dégagement de Outil Fonctions 2 à Roues des d’orientation CommandeGoulotte la de Commande Goulotte la de directionSouffleuse la de Commandes Tarière la de Commande TiquesPneuma Bandages pneus des Pression Pas Goulotte la de dégagement de OutilBien passe qu’il ce jusqu’à raccord le sur Tapez Vitesses de levier du tige la de InstallationGoulotte la de Installation «Réglages»Cisaillement de Boulons Goulotte la de manivelle la de MontageGuidon du Montage ’assemblage pour requis ArticlesGaz de émissions les concernant Avis Remisage et EntretienResponsabilité Votre Moyenne utile vie de Durée’essence de Manipulation PréparationFormation VotreMachine la d’utiliser Sécurité de SymbolesMatières des Table Vente-après ServiceVente-après service au d’abord adresser vous sans Modèle de numéro le trouver Pour04179-769 ’UTILISATION Notice

769-04179 specifications

The MTD 769-04179 is a powerful and versatile lawn mower designed to meet the needs of homeowners seeking efficiency, durability, and ease of use in lawn care. This model stands out in the competitive market of outdoor power equipment, equipped with a range of features that enhance performance and user experience.

One of the primary characteristics of the MTD 769-04179 is its robust engine. It boasts a reliable gas-powered engine that delivers impressive torque and cutting power. This engine is designed to handle various lawn conditions, making it suitable for small to moderate-sized yards. The mower’s cutting deck typically measures between 20 to 22 inches, allowing users to cover more area with each pass while maintaining precision cutting.

The MTD 769-04179 also integrates advanced cutting technologies. The mower features a 3-in-1 cutting system that allows users to mulch, bag, or side discharge grass clippings based on their preferences and lawn care needs. This capability not only promotes a healthier lawn but also offers flexibility in managing grass waste. The adjustable cutting height is another key attribute, enabling users to select the ideal grass length for their specific lawn type and conditions.

In terms of user comfort and convenience, the MTD 769-04179 is designed with an ergonomic handle, which reduces strain during extended mowing sessions. The 769-04179 model generally includes easy-to-access controls for the engine start, speed adjustments, and cutting height selection, ensuring a seamless user experience.

Durability is also a prominent feature of this lawn mower. The MTD 769-04179 is constructed with high-quality materials that withstand the rigors of regular lawn maintenance. Its sturdy wheels provide excellent traction and maneuverability across different terrains, making it effective on both flat and uneven surfaces.

Maintenance is simplified in the MTD 769-04179, with user-friendly features that include easy access to the spark plug and air filter. This accessibility encourages regular upkeep, ensuring the mower remains in optimal working condition over time.

Overall, the MTD 769-04179 is a reliable choice for homeowners seeking an efficient and easy-to-handle lawn mower. With its powerful engine, versatile cutting options, and user-friendly design, it offers excellent value for those dedicated to maintaining a healthy and beautiful lawn.
Top Page Image Contents