MTD 769-04179 warranty Skid Shoes, Tire Pressure Pneumatic Tires, Auger Control

Page 9

A B

Drive

Auger

Figure 3-11

Loosen the Nylock nut on the drive control cable and unthread the cable one full turn. See Figure 3-13.

Recheck adjustment.

Retighten the Nylock nut to secure the cable when correct adjustment is reached.

NOTE: For more details, refer to Drive Control Adjust- ment in the Adjustment Section of this manual.

Auger Control

Check the adjustment of the auger control as follows:

When the auger control is released and in the disengaged “up” position (see Figure 3-11B), the cable should have very little slack, but should NOT be tight. See Figure 3-12.

WARNING:Do not over-tighten the cable. Over-tightening may prevent the auger from disengaging and compro- mise the safety of the snow thrower.

In a well-ventilated area, start the snow thrower engine as instructed on page 12.

While standing in the operator’s position (behind the snow thrower) engage the auger.

Allow the auger to remain engaged for approximately ten seconds before releasing the auger control. Repeat this several times.

With the auger control lever in the disengaged “up” position, walk to the front of the machine.

Confirm that the auger has completely stopped rotating and shows no signs of motion.

IMPORTANT: If the auger shows any signs of rotating, immediately return to the operator’s position and shut off the engine. Wait for all moving parts to stop before readjusting the auger control cable.

To readjust the control cable, unhook the spring (found on the end of the auger cable) from the auger actuator bracket. See Figure 3-12.

Push the cable coupler through the end of the spring to expose the lock nut. See Figure 3-13.

Thread the Nylock nut outward (down the coupler) three full turns to provide more slack in the cable and reattach the spring to the bracket.

A

B

A - For models with steel panels.

B - For models with plastic panels.

Figure 3-12

Figure 3-13

Repeat auger control test to verify for proper adjustment. Repeat previous steps to adjust more, if necessary.

Skid Shoes

Position the skid shoes based on surface conditions. Adjust upward for hard-packed snow. Adjust downward when operating on gravel or crushed rock surfaces. See “Making Adjustment” Section.

Tire Pressure (Pneumatic Tires)

The tires are over-inflated for shipping purposes. Check the tire pressure before operating the snow thrower. Refer to the tire side wall for tire manufacturer’s recommended psi and deflate (or inflate) the tires as necessary.

3

Setting Up

Your Snow

Thrower

WARNING

Never use your hands to clean snow and ice from the chute assembly or auger housing.

IMPORTANT

If the tire pressure is not equal in both tires, the unit may not travel in a straight path and the shave plate may wear unevenly.

9

Image 9
Contents Two-Stage Snow Thrower 769-0417906/25/08 Table of Contents Finding and Recording Model NumberCustomer Support There are rotating blades inside Safety SymbolsDo not use the engine’s electric starter in the rain Your Responsibility Restrict the useTraining Safe Operation PracticesPreparation Your ResponsibilityOperation Maintenance & StorageDo not modify engine Average Useful LifeItems Required For Assembly Setting Up Your Snow ThrowerLoose Parts Assembling HandleAttaching the Shift Rod Attaching the Chute AssemblyClean-Out Tool Lamp WiringFinal Adjustments Drift Cutters If EquippedSkid Shoes Check the adjustment of the auger control as followsTire Pressure Pneumatic Tires AugerKnow Your Snow Thrower Operating Your Snow Thrower$26% #/.42 Stopping The Engine Gas & Oil Fill-UpTo Engage Drive To Engage AugersOperating Tips Always observe safety rules when performing any maintenanceGeneral Recommendations If possible, remove snow immediately after it fallsMaking AdjustmentsShift Rod Drive ControlChute Bracket Adjustment Chute AssemblySee Figure Adjust skid shoes as follows Auger ControlMaintaining Your Snow Thrower LubricationReplacing Belts Remove Loosen Auger BeltPulley Slot Drive BeltChanging Friction Wheel Rubber Using a 3/4 wrench, hold the hex shaftSecure with the cupped washer and hex bolt removed earlier Friction WheelOff-Season Storage Problem Cause Remedy Trouble Shooting05.28.08 WarrantyFor parts and/or accessories refer to customer support on 6919 Parts List Pièces Détachées Adressez-vous au «Service après-vente»La page 2 pour ce qui concerne les pièces et/ou accessoires Torque to 21 ft./lbs. maximum 305-342 cc618-04514 Worm Gear Box Ass’y w/ grease fitting Part RÉF Pièce Description Ground wire to engine Plug into alternator Lead wire under fuel tankGround Plug into alternatorPage 41, pas de 1/2 po x 36 maillons Part RÉF Pièce Description For parts and/or accessories refer to customer support on Page Garantie cette de GarantiePas couvre ne limitée garantie Cette Com.mtdcanadaDépannage Solution Causes ProblèmeUse PropreAccompagne qui moteur du d’utilisation notice la dans Jours, 30 de plus pendant entreposé être doit moteur le SiEntretien Frottement de Roue’essieu de ’entraînement Courroie Éloignez Courroies les de Remplacement’enlevez Tarière la de d’entraînement CourroieRoues LubrificationVitesse de ment ’engrenageRéglages Des l’entraînement de Commande Vitesses de levier du TigeRoues ’utilisation Conseils Général d’ordre RecommandationsToucher Les de Évitez .65C 150F dépasser’huile et d’essence Pleins Faites NeGoulotte la de dégagement de Outil Goulotte la de Commande Roues des d’orientation CommandeGoulotte la de direction Fonctions 2 àSouffleuse la de Commandes Tarière la de Commande TiquesPneuma Bandages pneus des Pression Pas Goulotte la de dégagement de OutilGoulotte la de Installation Vitesses de levier du tige la de Installation«Réglages» Bien passe qu’il ce jusqu’à raccord le sur TapezGuidon du Montage Goulotte la de manivelle la de Montage’assemblage pour requis Articles Cisaillement de BoulonsResponsabilité Votre Remisage et EntretienMoyenne utile vie de Durée Gaz de émissions les concernant AvisFormation PréparationVotre ’essence de ManipulationMachine la d’utiliser Sécurité de SymbolesVente-après service au d’abord adresser vous sans Vente-après ServiceModèle de numéro le trouver Pour Matières des Table04179-769 ’UTILISATION Notice

769-04179 specifications

The MTD 769-04179 is a powerful and versatile lawn mower designed to meet the needs of homeowners seeking efficiency, durability, and ease of use in lawn care. This model stands out in the competitive market of outdoor power equipment, equipped with a range of features that enhance performance and user experience.

One of the primary characteristics of the MTD 769-04179 is its robust engine. It boasts a reliable gas-powered engine that delivers impressive torque and cutting power. This engine is designed to handle various lawn conditions, making it suitable for small to moderate-sized yards. The mower’s cutting deck typically measures between 20 to 22 inches, allowing users to cover more area with each pass while maintaining precision cutting.

The MTD 769-04179 also integrates advanced cutting technologies. The mower features a 3-in-1 cutting system that allows users to mulch, bag, or side discharge grass clippings based on their preferences and lawn care needs. This capability not only promotes a healthier lawn but also offers flexibility in managing grass waste. The adjustable cutting height is another key attribute, enabling users to select the ideal grass length for their specific lawn type and conditions.

In terms of user comfort and convenience, the MTD 769-04179 is designed with an ergonomic handle, which reduces strain during extended mowing sessions. The 769-04179 model generally includes easy-to-access controls for the engine start, speed adjustments, and cutting height selection, ensuring a seamless user experience.

Durability is also a prominent feature of this lawn mower. The MTD 769-04179 is constructed with high-quality materials that withstand the rigors of regular lawn maintenance. Its sturdy wheels provide excellent traction and maneuverability across different terrains, making it effective on both flat and uneven surfaces.

Maintenance is simplified in the MTD 769-04179, with user-friendly features that include easy access to the spark plug and air filter. This accessibility encourages regular upkeep, ensuring the mower remains in optimal working condition over time.

Overall, the MTD 769-04179 is a reliable choice for homeowners seeking an efficient and easy-to-handle lawn mower. With its powerful engine, versatile cutting options, and user-friendly design, it offers excellent value for those dedicated to maintaining a healthy and beautiful lawn.