MTD 769-03265 warranty Maintaining Your Snow Thrower, Engine, Lubrication, Augers

Page 16

6

Maintaining

Your Snow

Thrower

WARNING

Before lubricating, repairing, or inspect- ing, disengage all controls and stop engine. Wait until all moving parts have come to a complete stop.

Keep all grease and oil off of the rubber friction wheel and aluminum drive plate.

Engine

Refer to the separate engine manual packed with your unit for all engine maintenance.

Lubrication

Engine

Refer to the separate engine manual packed with your unit for all engine lubrication instructions.

Gear Shaft

The gear (hex) shaft should be lubricated at least once a season or after every 25 hours of operation.

1.Carefully pivot the snow thrower up and forward so that it rests on the auger housing.

2.Remove the lower frame cover by removing the two screws which secure it.

3.Apply a light coating of an all-weather multi-purpose oil to the hex shaft. See Figure 6-1.

NOTE: Avoid getting oil on rubber friction wheel and aluminum drive plate.

Wheels

At least once a season, remove both wheels. Clean and coat the axles with a multipurpose automotive grease before reinstalling wheels.

Chute Directional Control (optional)

Once a season, the joystick should be lubricated with petroleum jelly, linseed oil, mineral oil, paraffin wax or 3-in-1 oil.

Auger Shaft

At least once a season, remove the shear pins on auger shaft. Spray lubricant inside shaft, around the spacers. Also lubricate the flange bearings found at either end of the shaft. See Figure 6-2.

Augers

•The augers are secured to the spiral shaft with two shear pins and cotter pins. If the auger should strike a foreign object or ice jam, the snow thrower is designed so that the pins may shear. Refer to Figure 6-2.

•If the augers will not turn, check to see if the pins have sheared. One set of replacement shear pins has been provided with the snow thrower. When replacing pins, spray an oil lubricant into shaft before inserting new pins.

Shave Plate and Skid Shoes

The shave plate and skid shoes on the bottom of the snow thrower are subject to wear. They should be checked periodically and replaced when necessary. To remove skid shoes:

1.Remove the four carriage bolts and hex flange nuts which secure them to the snow thrower.

2.Reassemble new skid shoes with the four carriage bolts (two on each side) and hex flange nuts. Refer to Figure 6-3.

 

Figure 6-1

 

3HEARE0IN

3PACERS

"EARING

 

 

 

Figure 6-2

 

Figure 6-3

To remove shave plate:

1.Remove the carriage bolts and hex nuts which attach it and the skid shoes to the snow thrower housing.

2.Reassemble new shave plate, making sure heads of carriage bolts are to the inside of housing. Tighten securely.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents 769-03265 Two-Stage Snow Thrower08/21/07 Finding and Recording Model Number Table of ContentsCustomer Support Chute Clean-out Tool Your Responsibility Restrict the useSafe Operation Practices TrainingPreparation Your ResponsibilityMaintenance & Storage OperationDo not modify engine Average Useful LifeSetting Up Setting Up Your Snow Thrower Shear Pin Storage optionalSnowthrower Model Drift Cutters If EquippedAll models Clean-Out Tool Lamp Wiring Harness If equippedSkid Shoes Tire Pressure Pneumatic TiresOperating Your Snow Thrower Know Your Snow Thrower$26% #/.42 Stopping The Engine Gas & Oil Fill-UpElectric Starter If Equipped To Engage Drive To Engage AugersRecoil Starter Auger Control TestMaking Adjustments Shift CableChute Control Drive Control & Shift LeverStandard Skid Shoe Reversible Skid ShoeMaintaining Your Snow Thrower EngineLubrication AugersRoll the auger belt off the engine pulley. See Figure Auger Belt ReplacementUnhook the support bracket spring from the frame Friction Wheel Inspection Drive Belt ReplacementRemove and replace belt in the reverse order Off-Season Storage Wipe equipment with an oiled rag to prevent rustTrouble Shooting Problem Cause RemedyWarranty 06.18.06OHV Part Description RÉF Pièce 30 in/po Remarque Lhabitacle peut être légèrement différent 5952Part Description RÉF Pièce 31AE6GKF500 Part Manual Chute Control Part Description RÉF Pièce Auger Housing COMPONENTS/COMPOSANTS DU Logement DES Tarières Garantie FrottementSolution Causes Problème DépannageSouffleuse Propre etCarburant le Videz Gaz Régime ’entretienFrottement de roue la de Inspection Transmission de courroie la de Remplacement Ne Remarque Les RemarqueLa de courroie la de Remplacement Patins et plate LameTarière LubrificationTarière la de Commande RéglagesPatins Plastique en réversible Patins 4-5 FigureEt transmission la de Commande Goulotte la de CommandeVitesses de levier Vitesses de changement de CâbleSouffleuse MainToucher 150F dépasser’huile et d’essence Pleins Modèles certains sur électrique DémarreurModèles Certains sur électrique DémarreurTrans de commande la de Blocage La de proximité àSouffleuse la 33/-3.42Souffleuse la de Commandes Départ de VoletGénéral d’ordre Recommandations Goulotte la de dégagement de OutilPneumatiques Bandages pneus des Pression Goulotte la de dégagement de OutilÉchéant cas le coupe de Barres Option en cisaillement de goupille la de Remisage Cette Remarque Les RemarqueRemisage et Entretien Responsabilité VotreMoyenne utile vie de Durée Gaz de émissions les concernant AvisUtilisation PréparationFormation Responsabilité VotreSécurité de Étiquettes Est goulotte la de dégagement de outil UnVente-après Service Modèle de numéro le trouver PourMatières des Table ’utilisation La voir détachées PiècesPhases deux neige à eSouffleus 08/21/07

769-03265 specifications

The MTD 769-03265 is a robust and versatile lawn mower designed to meet the needs of both homeowners and professionals. As a part of MTD's esteemed product line, this model excels in delivering high performance and reliability for lawn care enthusiasts.

One of the main features of the MTD 769-03265 is its powerful engine. Equipped with a high-torque 140cc engine, it provides optimal cutting power, ensuring that even thick grass can be managed with ease. This engine is paired with a user-friendly recoil start system, making it simple to get the mower running quickly and efficiently.

The cutting deck of the MTD 769-03265 measures 21 inches, which strikes a perfect balance between maneuverability and efficiency. This size allows for tight cornering and easy navigation around landscaping while still providing a wide cutting path to reduce mowing time. Additionally, this mower comes with a 3-in-1 capability, allowing users to choose between mulching, side discharging, or bagging grass clippings. This versatility caters to various mowing preferences and lawn care needs.

Another standout characteristic is the adjustable height settings. The MTD 769-03265 features six different cutting height options, ranging from 1.25 inches to 3.75 inches. This flexibility enables users to customize their mowing experience based on the specific type of grass and seasonal conditions, which is crucial for maintaining a healthy lawn.

The design of the mower also emphasizes comfort and ease of use. It includes an ergonomic handle that can be adjusted for height, allowing users of all sizes to operate the machine comfortably. The handle is also foldable, making storage a breeze. Additionally, the mower’s lightweight construction facilitates easy maneuverability, making it suitable for all types of lawn terrains.

MTD has also focused on enhancing user safety with the incorporation of safety features like automatic blade stop technology. This ensures that the blades cease operation immediately when the operator is not in control, reducing the risk of accidents.

In summary, the MTD 769-03265 combines a powerful engine, a versatile cutting system, and user-friendly design to deliver an exceptional mowing experience. Whether for residential use or professional landscaping, this mower is equipped to handle various lawn care tasks, making it a valuable addition to any homeowner's or landscaper's toolkit.
Top Page Image Contents