MTD 769-03265 warranty Clean-Out Tool, Lamp Wiring Harness If equipped, Skid Shoes

Page 9

Clean-Out

Tool

Figure 3-9

Clean-Out Tool

The clean-out tool is mounted to the rear of the auger housing and is designed to clear a clogged chute. Refer to page 11 for instructions on how to properly use it.

NOTE: This item is fastened with a cable tie to the rear of the auger housing at the factory. Cut the cable tie before operating the snow thrower.

WARNING: Never use your hands to clean snow and ice from the chute assembly or auger housing.

3

Setting Up

Your Snow

Thrower

Lamp Wiring Harness (If equipped)

The post on the cable tie attaching the lamp wiring harness to the lower handle should be plugged into the hole in the lower handle. Pull the slack portion of the wiring harness through the cable tie to prevent interfer- ence with the recoil starter handle.

Figure 3-10

WARNING

Never use your hands to clean snow and ice from the chute assembly or auger housing.

Skid Shoes

Position the skid shoes based on surface conditions. Adjust upward for hard-packed snow. Adjust downward when operating on gravel or crushed rock surfaces. See “Making Adjustment” Section.

Tire Pressure (Pneumatic Tires)

The tires are over-inflated for shipping purposes. Check the tire pressure before operating the snow thrower. Refer to the tire side wall for tire manufacturer’s recommended psi and deflate (or inflate) the tires as necessary.

NOTE: If the tire pressure is not equal in both tires, the unit may not travel in a straight path and the shave plate may wear unevenly.

General Recommendations

1.Always observe safety rules when performing any maintenance.

2.The warranty on this snow thrower does not cover items that have been subjected to operator abuse or negligence. To receive full value from warranty, operator must maintain the snow thrower as instructed here.

3.Some adjustments will have to be made periodically to maintain your unit properly.

4.Periodically check all fasteners and make sure these are tight.

IMPORTANT

Under any circum- stance do not exceed manufacturer’s recom- mended psi. Equal tire pressure should be maintained at all times. Excessive pressure when seating beads may cause tire/rim assembly to burst with force sufficient to cause serious injury. Refer to sidewall of tire for recommended pressure.

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Two-Stage Snow Thrower 769-0326508/21/07 Table of Contents Finding and Recording Model NumberCustomer Support Your Responsibility Restrict the use Chute Clean-out ToolTraining Safe Operation PracticesPreparation Your ResponsibilityOperation Maintenance & StorageDo not modify engine Average Useful LifeSetting Up Shear Pin Storage optional Setting Up Your Snow ThrowerDrift Cutters If Equipped Snowthrower ModelAll models Lamp Wiring Harness If equipped Clean-Out ToolSkid Shoes Tire Pressure Pneumatic TiresKnow Your Snow Thrower Operating Your Snow Thrower$26% #/.42 Gas & Oil Fill-Up Stopping The EngineElectric Starter If Equipped To Engage Augers To Engage DriveRecoil Starter Auger Control TestShift Cable Making AdjustmentsChute Control Drive Control & Shift LeverReversible Skid Shoe Standard Skid ShoeEngine Maintaining Your Snow ThrowerLubrication AugersAuger Belt Replacement Roll the auger belt off the engine pulley. See FigureUnhook the support bracket spring from the frame Drive Belt Replacement Friction Wheel InspectionRemove and replace belt in the reverse order Wipe equipment with an oiled rag to prevent rust Off-Season StorageProblem Cause Remedy Trouble Shooting06.18.06 WarrantyOHV Part Description RÉF Pièce Remarque Lhabitacle peut être légèrement différent 5952 30 in/poPart Description RÉF Pièce 31AE6GKF500 Part Manual Chute Control Part Description RÉF Pièce Auger Housing COMPONENTS/COMPOSANTS DU Logement DES Tarières Frottement GarantieDépannage Solution Causes ProblèmePropre et SouffleuseCarburant le Videz Gaz ’entretien RégimeFrottement de roue la de Inspection Transmission de courroie la de Remplacement Les Remarque Ne RemarquePatins et plate Lame La de courroie la de RemplacementTarière LubrificationRéglages Tarière la de CommandePatins Plastique en réversible Patins 4-5 FigureGoulotte la de Commande Et transmission la de CommandeVitesses de levier Vitesses de changement de CâbleMain SouffleuseToucher 150F dépasserModèles certains sur électrique Démarreur ’huile et d’essence PleinsModèles Certains sur électrique DémarreurLa de proximité à Trans de commande la de BlocageSouffleuse la 33/-3.42Départ de Volet Souffleuse la de CommandesGoulotte la de dégagement de Outil Général d’ordre RecommandationsPneumatiques Bandages pneus des Pression Goulotte la de dégagement de OutilÉchéant cas le coupe de Barres Option en cisaillement de goupille la de Remisage Les Remarque Cette RemarqueResponsabilité Votre Remisage et EntretienMoyenne utile vie de Durée Gaz de émissions les concernant AvisPréparation UtilisationFormation Responsabilité VotreEst goulotte la de dégagement de outil Un Sécurité de ÉtiquettesModèle de numéro le trouver Pour Vente-après ServiceMatières des Table ’utilisation La voir détachées Pièces08/21/07 Phases deux neige à eSouffleus

769-03265 specifications

The MTD 769-03265 is a robust and versatile lawn mower designed to meet the needs of both homeowners and professionals. As a part of MTD's esteemed product line, this model excels in delivering high performance and reliability for lawn care enthusiasts.

One of the main features of the MTD 769-03265 is its powerful engine. Equipped with a high-torque 140cc engine, it provides optimal cutting power, ensuring that even thick grass can be managed with ease. This engine is paired with a user-friendly recoil start system, making it simple to get the mower running quickly and efficiently.

The cutting deck of the MTD 769-03265 measures 21 inches, which strikes a perfect balance between maneuverability and efficiency. This size allows for tight cornering and easy navigation around landscaping while still providing a wide cutting path to reduce mowing time. Additionally, this mower comes with a 3-in-1 capability, allowing users to choose between mulching, side discharging, or bagging grass clippings. This versatility caters to various mowing preferences and lawn care needs.

Another standout characteristic is the adjustable height settings. The MTD 769-03265 features six different cutting height options, ranging from 1.25 inches to 3.75 inches. This flexibility enables users to customize their mowing experience based on the specific type of grass and seasonal conditions, which is crucial for maintaining a healthy lawn.

The design of the mower also emphasizes comfort and ease of use. It includes an ergonomic handle that can be adjusted for height, allowing users of all sizes to operate the machine comfortably. The handle is also foldable, making storage a breeze. Additionally, the mower’s lightweight construction facilitates easy maneuverability, making it suitable for all types of lawn terrains.

MTD has also focused on enhancing user safety with the incorporation of safety features like automatic blade stop technology. This ensures that the blades cease operation immediately when the operator is not in control, reducing the risk of accidents.

In summary, the MTD 769-03265 combines a powerful engine, a versatile cutting system, and user-friendly design to deliver an exceptional mowing experience. Whether for residential use or professional landscaping, this mower is equipped to handle various lawn care tasks, making it a valuable addition to any homeowner's or landscaper's toolkit.
Top Page Image Contents