MTD 769-04164 warranty Stopping the Engine, Auger Control Test, Operating The Snowthrower

Page 10

5

Operation

WARNING

The operation of any snow thrower can result in foreign objects being thrown into the eyes, which can damage your eyes severely. Always wear safety glasses while operating the snow thrower, or while performing any adjustments or repairs on it.

Be sure no one other than the operator is standing near the snow thrower while starting engine or operating snow thrower. Never run engine indoors or in enclosed, poorly ven- tilated areas. Engine exhaust contains carbon monoxide, an odorless and deadly gas. Keep hands, feet, hair and loose clothing away from any moving parts on engine and snow thrower.

Stopping the Engine

WARNING: To avoid unsupervised engine operation, never leave the engine unattended while running. Turn the engine off after use and remove ignition key

Run engine for a few minutes before stopping to help dry off any moisture on the engine.

1.Move throttle control to STOP position.

2.Remove the ignition key. Removing the key will reduce the possibility of unauthorized starting of the engine while equipment is not in use. Keep the key in a safe place. The engine cannot start without the ignition key.

3.Wipe all snow and moisture from the area around the engine as well as the area in and around the drive control and auger control. Also, engage and release both controls several times.

Auger Control Test

IMPORTANT: Perform the following test before operat- ing the snow thrower for the first time and at the start of each season.

Check the adjustment of the auger control as follows:

1.When the auger control is released and in the disengaged “up” position, the cable should have very little slack, but should NOT be tight.

2.In a well-ventilated area, start the snow thrower engine as instructed earlier in this section under the heading Starting Engine. Make sure the throttle is set in the FAST position.

3.While standing in the operator’s position (behind the snow thrower) engage the auger.

4.Allow the auger to remain engaged for approximately ten (10) seconds before releasing the auger control. Repeat this several times.

5.With the engine running in the FAST position and the auger control in the disengaged “up” position, walk to the front of the machine.

6.Confirm that the auger has completely stopped rotating and shows NO signs of motion.

IMPORTANT: If the auger shows ANY signs of rotating, immediately return to the operator’s position and shut off the engine. Wait for all moving parts to stop before readjusting the auger control cable as shown in the “Setup And Adjustment” section on page 7.

Operating The Snowthrower

NOTE: Allow the engine to warm up for a few minutes as the engine will not develop full power until it reaches operating temperature.

•Adjust the discharge chute as desired. Do not throw snow toward a building as hidden objects could be discharged with enough force to cause damage.

•Start the engine as instructed previously.

•Making certain no bystanders or obstacles are in front of the unit, squeeze the auger control bail completely against the upper handle to fully engage the augers.

Release the auger control bail and the augers will stop.

•While the auger control handle is engaged, squeeze the drive control bail completely against the upper handle to engage the wheels. Release the drive control bail and the wheels will stop.

•As the snowthrower starts to move, maintain a firm hold on the handle, and guide the snowthrower along the path to be cleared.

•Release the bails to stop the snowthrowing action and forward motion.

NOTE: Your unit is equipped with a clutch in the transmis- sion. If the wheels stop turning while trying to discharge large volumes of snow, immediately disengage the drive control bail and allow the rotating augers to discharge snow from the housing. Continue operation reducing clearing width.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents 769-04164 06/17/08Table of Contents Do not use the engine’s electric starter in the rain Safety SymbolsThere are rotating blades inside Your Responsibility Restrict the usePreparation Safe Operation PracticesTraining Your ResponsibilityDo not modify engine Maintenance & StorageOperation Average Useful LifeClean-Out Tool Setting Up The HandleChute Handle Skid Shoe Setting Up Your Snow ThrowerFinal Adjustments Auger CableIgnition Key Throttle ControlDrive Control Shave PlateEngines with Starter Handle non-electric start Starting the EngineGas and Oil Fill-up Engines with Electric StartersOperating The Snowthrower Stopping the EngineAuger Control Test Start the engine as instructed previouslyOperating Tips Clean-Out ToolClean the snowthrower thoroughly after each use Stop Engine to prevent possible freeze-upMaintenance Service Drive Belt Install new auger beltAuger Belt Drive BeltOff-Season Storage Wipe equipment with an oiled rag to prevent rustTrouble Shooting Illustrated Parts Pièces Détachés Adressez-vous au «Service après-vente» Part RÉF Pièce Description2022 31A-3AAD2 Year Limited Warranty WarrantyGarantie Dépannage PasSaison hors RemisageTransmission la de Courroie EntretienTarières des Courroie Courroies la Inspectez Courroie la de RemplacementMoteur Goulotte la de dégagement de Outil ’utilisation Conseils La de et moteur du Souffleuse la de UtilisationSouffleuse Non vêtements etMoteur du marche en Mise Démarrage le AvantOption en électrique Démarreur ’huile et d’essence PleinsSouffleuse la de Commandes ’éjection GoulotteRéglages Derniers Réglage et MontagePatins Guidon du Installation RéglageMoyenne utile vie de Durée Remisage et EntretienResponsabilité Votre Gaz de émissions les concernant AvisFormation PréparationVotre Sécurité de Symboles 5218-523-866-1 2B8 M4S .ONT TORONTO, Yardworks Série de Numéro Modèle de Numéro Number Serial Number ModelAU Vente Aprés Service LE Appelez 04164-769

769-04164 specifications

The MTD 769-04164 is a powerful and versatile machine designed for a variety of outdoor maintenance tasks. It is a significant addition to MTD's lineup of reliable gardening and landscaping equipment, showcasing advancements in technology and user-friendly features.

One of the standout characteristics of the MTD 769-04164 is its robust engine. Equipped with a dependable gas-powered motor, this machine delivers significant power, allowing users to efficiently tackle tougher tasks such as large lawn areas, heavy shrubbery, and various terrain types. The engine's efficiency ensures a good balance of performance and fuel consumption, making it a cost-effective solution for homeowners and professionals alike.

The design of the MTD 769-04164 prioritizes user ergonomics, featuring a comfortable grip and intuitive controls. This means that whether you are a seasoned gardener or a novice, you can easily operate the machine with minimal learning curve. The adjustable handle height is an added advantage, accommodating users of different heights and providing optimal comfort during operation.

In terms of technology, the MTD 769-04164 integrates innovative features to enhance usability. One notable technology is its easy-start mechanism, which allows the engine to start with less effort, reducing the hassle usually associated with starting gas engines. This is especially useful in colder weather or for those who may have difficulty with traditional pull-starts.

Furthermore, this model is designed with efficient mowing and trimming capabilities, boasting sharp, durable blades that ensure a clean, precise cut. The adjustable cutting height feature provides flexibility, allowing users to choose the ideal grass length for their lawns. This adaptability is crucial for maintaining a healthy lawn while catering to personal aesthetic preferences.

Maintenance is simplified with the MTD 769-04164, featuring accessible components that make routine checks and servicing straightforward. Regular maintenance can significantly prolong the machine's lifespan, and MTD has ensured it is as user-friendly as possible.

In summary, the MTD 769-04164 is an exemplary outdoor maintenance tool, combining power, comfort, and innovative technology. Whether you're maintaining a residential landscape or managing larger grounds, it proves to be a reliable choice that meets diverse outdoor needs with efficiency and ease.
Top Page Image Contents