MTD 769-04164 warranty Auger Belt, Drive Belt, Install new auger belt

Page 13

Plastic Tab

Figure 11

Auger Belt

Engine

Pulley

Drive

Belt

Auger

Pulley

Idler

Bracket

Figure 12

Spring

Drive Pulley

Belt Keeper

Drive Belt

 

 

Figure 13

3.Remove the self tapping screw which secures the belt cover to the frame. Remove the belt cover by pushing in on the sides of the cover to release the plastic tabs. Pull the belt cover out from around the engine and chute. See Figure 11.

Auger Belt

NOTE: Drain the gasoline from the snowthrower, or place a piece of plastic under the gas cap.

1.Tip the snow thrower up and forward so that it rests on the auger housing. Remove the belt keeper as shown in Figure 13. Return the snow thrower to its upright position to complete the following steps.

2.Slip the front auger belt off of the engine pulley pushing it forward and rolling in off of the pulley. See Figure 12.

3.Squeeze the auger control handle to release the auger brake, which is the tab that holds the belt onto the auger pulley. Remove the belt.

4.Replace with new belt after replacing the drive belt.

Drive Belt

NOTE: Replace the drive belt before reassembling the new auger belt.

NOTE: Drain the gasoline from the snowthrower, or place a piece of plastic under the gas cap.

1.Tip the snow thrower up and forward so that it rests on the auger housing.

2.Remove the spring that connects the transmission to a bolt on the engine frame. See Figure 13.

NOTE: It may be easier to first remove the flange lock nut, then use needle-nosed pliers to firmly grip spring and remove from bolt.

3.Pivot the transmission forward to release pressure on the drive belt. Remove belt from transmission pulley.

4.Remove the drive belt from around the engine pulley, and away from the unit.

5.Place the new drive belt into the groove on the engine pulley. See Figure 12.

6.Tilt the transmission forward and position the drive belt onto the transmission pulley.

7.Reconnect the spring to the bolt on the engine frame and secure the transmission. Reinstall the flange lock nut.

8.Install new auger belt.

6

Maintenance

& Service

WARNING

Always stop engine, disconnect spark plug, and ground against engine before cleaning, lubricating or doing any kind

of maintenance or adjustments on your machine.

13

Image 13
Contents 06/17/08 769-04164Table of Contents There are rotating blades inside Safety SymbolsDo not use the engine’s electric starter in the rain Your Responsibility Restrict the useTraining Safe Operation PracticesPreparation Your ResponsibilityOperation Maintenance & StorageDo not modify engine Average Useful LifeClean-Out Tool Setting Up The HandleChute Handle Final Adjustments Setting Up Your Snow ThrowerSkid Shoe Auger CableDrive Control Throttle ControlIgnition Key Shave PlateGas and Oil Fill-up Starting the EngineEngines with Starter Handle non-electric start Engines with Electric StartersAuger Control Test Stopping the EngineOperating The Snowthrower Start the engine as instructed previouslyClean the snowthrower thoroughly after each use Clean-Out ToolOperating Tips Stop Engine to prevent possible freeze-upMaintenance Service Auger Belt Install new auger beltDrive Belt Drive BeltWipe equipment with an oiled rag to prevent rust Off-Season StorageTrouble Shooting Illustrated Parts Pièces Détachés Part RÉF Pièce Description Adressez-vous au «Service après-vente»2022 31A-3AAD2 Warranty Year Limited WarrantyGarantie Pas DépannageRemisage Saison horsTransmission la de Courroie EntretienTarières des Courroie Courroies la Inspectez Courroie la de RemplacementMoteur Goulotte la de dégagement de Outil ’utilisation Conseils Souffleuse Souffleuse la de UtilisationLa de et moteur du Non vêtements etOption en électrique Démarreur Démarrage le AvantMoteur du marche en Mise ’huile et d’essence Pleins’éjection Goulotte Souffleuse la de CommandesRéglages Derniers Réglage et MontagePatins Réglage Guidon du InstallationResponsabilité Votre Remisage et EntretienMoyenne utile vie de Durée Gaz de émissions les concernant AvisFormation PréparationVotre Sécurité de Symboles Série de Numéro Modèle de Numéro Number Serial Number Model 5218-523-866-1 2B8 M4S .ONT TORONTO, Yardworks04164-769 AU Vente Aprés Service LE Appelez

769-04164 specifications

The MTD 769-04164 is a powerful and versatile machine designed for a variety of outdoor maintenance tasks. It is a significant addition to MTD's lineup of reliable gardening and landscaping equipment, showcasing advancements in technology and user-friendly features.

One of the standout characteristics of the MTD 769-04164 is its robust engine. Equipped with a dependable gas-powered motor, this machine delivers significant power, allowing users to efficiently tackle tougher tasks such as large lawn areas, heavy shrubbery, and various terrain types. The engine's efficiency ensures a good balance of performance and fuel consumption, making it a cost-effective solution for homeowners and professionals alike.

The design of the MTD 769-04164 prioritizes user ergonomics, featuring a comfortable grip and intuitive controls. This means that whether you are a seasoned gardener or a novice, you can easily operate the machine with minimal learning curve. The adjustable handle height is an added advantage, accommodating users of different heights and providing optimal comfort during operation.

In terms of technology, the MTD 769-04164 integrates innovative features to enhance usability. One notable technology is its easy-start mechanism, which allows the engine to start with less effort, reducing the hassle usually associated with starting gas engines. This is especially useful in colder weather or for those who may have difficulty with traditional pull-starts.

Furthermore, this model is designed with efficient mowing and trimming capabilities, boasting sharp, durable blades that ensure a clean, precise cut. The adjustable cutting height feature provides flexibility, allowing users to choose the ideal grass length for their lawns. This adaptability is crucial for maintaining a healthy lawn while catering to personal aesthetic preferences.

Maintenance is simplified with the MTD 769-04164, featuring accessible components that make routine checks and servicing straightforward. Regular maintenance can significantly prolong the machine's lifespan, and MTD has ensured it is as user-friendly as possible.

In summary, the MTD 769-04164 is an exemplary outdoor maintenance tool, combining power, comfort, and innovative technology. Whether you're maintaining a residential landscape or managing larger grounds, it proves to be a reliable choice that meets diverse outdoor needs with efficiency and ease.