MTD 769-04164 warranty Safe Operation Practices, Training, Preparation, Your Responsibility

Page 4

2

Safe

Operation

WARNING: Engine Exhaust, some of its constituents, and certain vehicle compo- nents contain or emit chemicals known to State of California to cause cancer and birth defects or other reproductive harm.

DANGER: This machine was built to be operated according to the safe operation practices in this manual. As with any type of power equipment, carelessness or error on the part of the operator can result in serious injury. This machine is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury or death.

Practices

WARNING

This symbol points out important safety instructions which, if not followed, could endanger the per- sonal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate this machine. Failure to comply with these instructions may result in personal injury. When you see this symbol, HEED

ITS WARNING!

Your Responsibility

Restrict the use

of this power machine to persons who read, understand

and follow the warnings and instructions

in this manual

and on the machine.

Training

1.Read, understand, and follow all instructions on the machine and in the manual(s) before attempting to assemble and operate. Keep this manual in a safe place for future and regular reference and for ordering replacement parts.

2.Be familiar with all controls and their proper operation. Know how to stop the machine and disengage them quickly.

3.Never allow children under 14 years old to operate this machine. Children 14 years old and over should read and understand the instructions and safe operation practices in this manual and on the machine and be trained and supervised by an adult.

4.Never allow adults to operate this machine without proper instruction.

5.Thrown objects can cause serious personal injury. Plan your snow-throwing pattern to avoid discharge of material toward roads, bystanders and the like.

6.Keep bystanders, helpers, pets and children at least 75 feet from the machine while it is in operation. Stop machine if anyone enters the area.

7.Exercise caution to avoid slipping or falling, especially when operating in reverse.

Preparation

Thoroughly inspect the area where the equipment is to be used. Remove all doormats, newspapers, sleds, boards, wires and other foreign objects, which could be tripped over or thrown by the auger/impeller.

1.Always wear safety glasses or eye shields during operation and while performing an adjustment or repair to protect your eyes. Thrown objects which ricochet can cause serious injury to the eyes.

2.Do not operate without wearing adequate winter outer gar- ments. Do not wear jewelry, long scarves or other loose clothing, which could become entangled in moving parts. Wear footwear which will improve footing on slippery surfaces.

3.Use a grounded three-wire extension cord and receptacle for all units with electric start engines.

4.Adjust collector housing height to clear gravel or crushed rock surfaces.

5.Disengage all control levers before starting the engine.

6.Never attempt to make any adjustments while engine is running, except where specifically recommended in the operator’s manual.

7.Let engine and machine adjust to outdoor temperature before starting to clear snow.

Safe Handling of Gasoline

To avoid personal injury or property damage use extreme care in handling gasoline. Gasoline is extremely flammable and the vapors are explosive. Serious personal injury can occur when gasoline is spilled on yourself or your clothes, which can ignite. Wash your skin and change clothes immediately.

a.Use only an approved gasoline container.

b.Extinguish all cigarettes, cigars, pipes and other sources of ignition.

c.Never fuel machine indoors.

d.Never remove gas cap or add fuel while the engine is hot or running.

e.Allow engine to cool at least two minutes before refuel- ing.

f.Never over fill fuel tank. Fill tank to no more than ½ inch below bottom of filler neck to provide space for fuel expansion.

g.Replace gasoline cap and tighten securely.

h.If gasoline is spilled, wipe it off the engine and equip- ment. Move machine to another area. Wait 5 minutes before starting the engine.

i.Never store the machine or fuel container inside where there is an open flame, spark or pilot light (e.g. furnace, water heater, space heater, clothes dryer etc.).

j.Allow machine to cool at least 5 minutes before storing

k.Never fill containers inside a vehicle or on a truck or trailer bed with a plastic liner. Always place containers on the ground away from your vehicle before filling.

l.If possible, remove gas-powered equipment from the truck or trailer and refuel it on the ground. If this is not possible, then refuel such equipment on a trailer with a portable container, rather than from a gasoline dispenser nozzle.

m.Keep the nozzle in contact with the rim of the fuel tank or container opening at all times until fueling is complete. Do not use a nozzle lock-open device.

4

Page 3 Page 5
Image 4
Page 3 Page 5
Contents 769-04164 06/17/08Table of Contents Safety Symbols There are rotating blades insideDo not use the engine’s electric starter in the rain Your Responsibility Restrict the useSafe Operation Practices TrainingPreparation Your ResponsibilityMaintenance & Storage OperationDo not modify engine Average Useful LifeClean-Out Tool Setting Up The HandleChute Handle Setting Up Your Snow Thrower Final AdjustmentsSkid Shoe Auger CableThrottle Control Drive ControlIgnition Key Shave PlateStarting the Engine Gas and Oil Fill-upEngines with Starter Handle non-electric start Engines with Electric StartersStopping the Engine Auger Control TestOperating The Snowthrower Start the engine as instructed previouslyClean-Out Tool Clean the snowthrower thoroughly after each useOperating Tips Stop Engine to prevent possible freeze-upMaintenance Service Install new auger belt Auger BeltDrive Belt Drive BeltOff-Season Storage Wipe equipment with an oiled rag to prevent rustTrouble Shooting Illustrated Parts Pièces Détachés Adressez-vous au «Service après-vente» Part RÉF Pièce Description2022 31A-3AAD2 Year Limited Warranty WarrantyGarantie Dépannage PasSaison hors RemisageTransmission la de Courroie EntretienTarières des Courroie Courroies la Inspectez Courroie la de RemplacementMoteur Goulotte la de dégagement de Outil ’utilisation Conseils Souffleuse la de Utilisation SouffleuseLa de et moteur du Non vêtements etDémarrage le Avant Option en électrique DémarreurMoteur du marche en Mise ’huile et d’essence PleinsSouffleuse la de Commandes ’éjection GoulotteRéglages Derniers Réglage et MontagePatins Guidon du Installation RéglageRemisage et Entretien Responsabilité VotreMoyenne utile vie de Durée Gaz de émissions les concernant AvisFormation PréparationVotre Sécurité de Symboles 5218-523-866-1 2B8 M4S .ONT TORONTO, Yardworks Série de Numéro Modèle de Numéro Number Serial Number ModelAU Vente Aprés Service LE Appelez 04164-769

769-04164 specifications

The MTD 769-04164 is a powerful and versatile machine designed for a variety of outdoor maintenance tasks. It is a significant addition to MTD's lineup of reliable gardening and landscaping equipment, showcasing advancements in technology and user-friendly features.

One of the standout characteristics of the MTD 769-04164 is its robust engine. Equipped with a dependable gas-powered motor, this machine delivers significant power, allowing users to efficiently tackle tougher tasks such as large lawn areas, heavy shrubbery, and various terrain types. The engine's efficiency ensures a good balance of performance and fuel consumption, making it a cost-effective solution for homeowners and professionals alike.

The design of the MTD 769-04164 prioritizes user ergonomics, featuring a comfortable grip and intuitive controls. This means that whether you are a seasoned gardener or a novice, you can easily operate the machine with minimal learning curve. The adjustable handle height is an added advantage, accommodating users of different heights and providing optimal comfort during operation.

In terms of technology, the MTD 769-04164 integrates innovative features to enhance usability. One notable technology is its easy-start mechanism, which allows the engine to start with less effort, reducing the hassle usually associated with starting gas engines. This is especially useful in colder weather or for those who may have difficulty with traditional pull-starts.

Furthermore, this model is designed with efficient mowing and trimming capabilities, boasting sharp, durable blades that ensure a clean, precise cut. The adjustable cutting height feature provides flexibility, allowing users to choose the ideal grass length for their lawns. This adaptability is crucial for maintaining a healthy lawn while catering to personal aesthetic preferences.

Maintenance is simplified with the MTD 769-04164, featuring accessible components that make routine checks and servicing straightforward. Regular maintenance can significantly prolong the machine's lifespan, and MTD has ensured it is as user-friendly as possible.

In summary, the MTD 769-04164 is an exemplary outdoor maintenance tool, combining power, comfort, and innovative technology. Whether you're maintaining a residential landscape or managing larger grounds, it proves to be a reliable choice that meets diverse outdoor needs with efficiency and ease.
Top Page Image Contents