Poulan 421916 owner manual HOW to USE Your Snow Thrower, Stopping, To USE Choke Control See Fig

Page 10

OPERATION

The operation of any snow thrower can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear

safety glasses or eye shields while operating your snow thrower or performing any adjust- ments or repairs. We recommend standard safety glasses

or a wide vision safety mask worn over spectacles.

HOW TO USE YOUR SNOW THROWER

Know how to operate all controls before adding fuel or attempting to start the engine.

STOPPING

TRACTION DRIVE

•Release traction drive control lever to stop the forward or reverse movement of the snow thrower.

AUGER

•Release the auger control lever to stop throwing snow.

ENGINE

1.Move ON / OFF switch to “OFF” position.

2.Remove (do not turn) safety ignition key to prevent unauthorized use.

NOTE: Never use choke to stop engine.

TO USE CHOKE CONTROL (See Fig. 11)

The choke control is located on the engine. Use the choke control whenever you are starting a cold engine. Do not use to start a warm engine.

•To engage choke, turn knob counterclockwise. Slowly turn knob clockwise to disengage.

OFF

 

FULL

 

 

 

 

FIG. 11

TO CONTROL SNOW DISCHARGE (See Fig. 12)

WARNING: Snow throwers have ex- posed rotating parts, which can cause severe injury from contact, or from ma- terial thrown from the discharge chute. Keep the area of operation clear of all persons, small children and pets at all times including startup.

WARNING: If the discharge chute or au- ger become clogged, shut-off engine and wait for all moving parts to stop. Use the clean-out tool, NOT YOUR HANDS, to unclog the chute and/or auger.

The DIRECTION in which snow is to be thrown is controlled by the discharge chute control lever.

•To change the discharge chute position, press downward on discharge chute control lever and move lever left or right until chute is in desired position. Be sure lever springs back and locks into desired position.

The DISTANCE that snow is thrown is controlled by the position of the chute deflector. Set the deflector low to throw snow a short distance; set the deflector higher to throw snow farther.

•Press downward on chute deflector control lever and move lever forward to lower the deflector and decrease the distance. Move lever back to raise the deflector and increase the distance. Be sure lever springs back and locks into desired position.

DISCHARGE CHUTE

CONTROL LEVER

CHUTE DEFLECTOR

REMOTE CONTROL LEVER

FIG. 12

TO THROW SNOW (See Fig. 13)

The auger rotation is controlled by the auger control lever located on the right side handle.

•Squeeze auger control lever to handle to engage the auger and throw snow.

•Release the auger control lever to stop throwing snow.

AUGER

CONTROL

LEVER

FIG. 13

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Chute Deflector Remote Control Parts Packed Separately in CartonRemove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Unfold Upper HandleInstall Traction Drive Control ROD See Figs Install Auger Control ROD See FigsInstall Chute Deflector Remote Control See Figs Install Discharge Chute / Chute Rotater Head See FigCheck Tire Pressure Primer OperationKnow Your Snow Thrower Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting engineTo USE Choke Control See Fig HOW to USE Your Snow ThrowerStopping To Control Snow Discharge See FigPower Steering Operation See Fig Using the CLEAN-OUT Tool See FigTo Move Forward and Backward See Fig Scraper BAR See Fig To Adjust Skid Plates See FigBefore Starting the Engine Check Engine OIL Level See FigBefore Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has FrozenBefore Each USE MaintenanceGeneral Recommendations LubricationSnow Thrower CleaningEngine Chute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See FigTo Replace Belts See Fig Storage OtherTroubleshooting Exploded KEY Part Description Auger Assembly 30 RH Auger HousingAuger Assembly 30 LH Scrapper BARAuger Bearing Bearing PlugDeflector Weldment Deflector Control AssemblyChute Weldment Deflector SealRotator Pivot Bracket LEVER/CABLE Rotator AssemblyRotator Head Pulley Pivot419798X479 Loop Handle LHHandle Knob SpacerKnob RED Washer 3/8Shifter ROD TOP Impeller ROD AssemblyTraction ROD Assembly Shifter ROD BottomConsole Panel Wire Harness405784X479 Pivot Support Weldment Headlight BezelRepair Parts Snow Thrower Model 961940007 96194000701 Drive END Plate Speed Selector AssemblyDrive Plate Assembly Bottom PAN01.03.002-A Engine Model 20M314-0927-E1 409346X428 Frame Weldment 417015X428 Engine Mount PlateTraction Belt Belt CoverImpeller Belt Wheel Lobe CoverWheel Driver Retainer Ring Clutch SlideCable Bracket LH Cable Bracket RHSafety Ignition KEY 193071181037 DECAL, DangerService Notes Limited Warranty HOP

421916 specifications

The Poulan 421916 is a versatile and powerful hedge trimmer designed to meet the needs of both professional landscapers and homeowners. Renowned for its efficiency and ergonomic design, this tool makes hedge trimming a more manageable and enjoyable task.

One of the standout features of the Poulan 421916 is its robust engine. Equipped with a high-performance, lightweight motor, it delivers consistent power, allowing users to handle dense and overgrown hedges effortlessly. The engine is designed for easy starting, reducing frustration during setup.

The cutting blade is another significant highlight of the Poulan 421916. It features a dual-action design that minimizes vibration during operation, providing a smooth user experience. The blades are sharpened to precision, ensuring clean cuts and promoting healthy plant growth. With a cutting capacity of around 3/4 inch, it handles thick branches with ease, offering versatility for different tasks.

In addition to its powerful engine and efficient blades, the Poulan 421916 emphasizes user comfort. It features a lightweight and well-balanced design, which reduces fatigue during extended use. The comfortable grip handles are designed to provide maximum control, allowing for precise maneuvering around landscapes of all shapes and sizes.

Safety is another crucial aspect of the Poulan 421916. It comes equipped with safety guards and a blade brake system, which halts motion when not in use. These features protect the user from accidental injuries, making it a reliable choice for anyone concerned with safety while operating power equipment.

Technologically, the Poulan 421916 utilizes advanced anti-vibration technology. This innovation considerably reduces the amount of vibration transmitted to the user's hands and arms, allowing for prolonged use without discomfort. This technology is particularly beneficial for those who may be trimming hedges for extended periods.

In summary, the Poulan 421916 is an exceptional hedge trimmer that combines power, precision, and user-friendly features. With its efficient engine, sharp dual-action blades, lightweight design, and advanced safety measures, it stands as an excellent choice for anyone looking to maintain their outdoor spaces effectively. Whether you're a professional landscaper or a homeowner, the Poulan 421916 is engineered to help you achieve neat and tidy hedges with minimal effort.
Top Page Image Contents