Poulan 421916 Install Discharge Chute / Chute Rotater Head See Fig, Check Tire Pressure

Page 7

ASSEMBLY / PRE-OPERATION

INSTALL DISCHARGE CHUTE / CHUTE ROTATER HEAD (See Fig. 7)

NOTE: The multi-wrench provided in your parts bag may be used to install the chute rotater head.

1.Place discharge chute assembly on top of chute base with discharge opening toward front of snow thrower.

2.Position chute rotater head over chute bracket. If neces- sary, rotatechute assembly to align square and pin on un- derside of chute rotater head with holes in chute bracket.

3.With chute rotater head and chute bracket aligned, position chute rotater head on pin and threaded stud of mounting bracket.

4.Install 3/8 washer and locknut on threaded stud and tighten securely.

CHUTE

 

 

ROTATER

 

3/8 LOCKNUT

HEAD

 

 

 

 

3/8 WASHER

 

 

PIN

 

 

THREADED

 

 

STUD

 

ALIGN BEFORE

ROTATER HEAD

CHUTE

MOUNTING

BRACKET

TIGHTENING LOCKNUT

BRACKET

FIG. 7

INSTALL CHUTE DEFLECTOR REMOTE CONTROL (See Figs. 8 and 9)

1.Install remote cable bracket to discharge chute with 5/16-18 carriage bolt and 5/16-18 locknut as shown. Tighten securely.

2.Install remote cable eyelet to chute deflector with 1/4-20 shoulder bolt, nylon friction washer and 1/4-20 locknut as shown. Tighten securely.

3.Install spring hooks between hex nuts on chute rotater head and into hole in chute deflector as shown.

1/4-20

SPRING

CHUTE

SHOULDER

DEFLECTOR

BOLT

 

 

HOOK

NYLON

BETWEEN

WASHER

HEX NUTS

 

ON CHUTE

1/4-20

ROTATER

LOCKNUT

HEAD

 

5/16-18

 

CARRIAGE

 

BOLT

CABLE

 

EYELET

 

REMOTE

 

CABLE

 

BRACKET

 

5/16-18

 

LOCKNUT

 

FIG. 8

CHUTE DEFLECTOR

CONTROL LEVER

FIG. 9

CHECK TIRE PRESSURE

The tires on your snow thrower were overinflated at the fac- tory for shipping purposes. Correct and equal tire pressure is important for best snow throwing performance.

•Reduce tire pressure to 14-17 PSI (19-24.5 N-m).

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Chute Deflector Remote ControlUnfold Upper Handle Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from CartonInstall Auger Control ROD See Figs Install Traction Drive Control ROD See FigsInstall Chute Deflector Remote Control See Figs Install Discharge Chute / Chute Rotater Head See FigCheck Tire Pressure Ignition KEY OperationKnow Your Snow Thrower PrimerRecoil auxiliary starter handle used for starting engine Meets A.N.S.I. Safety RequirementsTo Control Snow Discharge See Fig HOW to USE Your Snow ThrowerStopping To USE Choke Control See FigPower Steering Operation See Fig Using the CLEAN-OUT Tool See FigTo Move Forward and Backward See Fig Check Engine OIL Level See Fig To Adjust Skid Plates See FigBefore Starting the Engine Scraper BAR See FigIf Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before StoppingLubrication MaintenanceGeneral Recommendations Before Each USESnow Thrower CleaningEngine Shear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Replace Belts See Fig Other StorageTroubleshooting Exploded KEY Part Description Scrapper BAR Auger HousingAuger Assembly 30 LH Auger Assembly 30 RHBearing Plug Auger BearingDeflector Seal Deflector Control AssemblyChute Weldment Deflector WeldmentPulley Pivot LEVER/CABLE Rotator AssemblyRotator Head Rotator Pivot BracketLoop Handle LH 419798X479Washer 3/8 SpacerKnob RED Handle KnobShifter ROD Bottom Impeller ROD AssemblyTraction ROD Assembly Shifter ROD TOPHeadlight Bezel Wire Harness405784X479 Pivot Support Weldment Console PanelRepair Parts Snow Thrower Model 961940007 96194000701 Drive Bottom PAN Speed Selector AssemblyDrive Plate Assembly END Plate01.03.002-A 409346X428 Frame Weldment 417015X428 Engine Mount Plate Engine Model 20M314-0927-E1Traction Belt Belt CoverImpeller Belt Clutch Slide CoverWheel Driver Retainer Ring Wheel LobeCable Bracket RH Cable Bracket LH193071 Safety Ignition KEYDECAL, Danger 181037Service Notes HOP Limited Warranty

421916 specifications

The Poulan 421916 is a versatile and powerful hedge trimmer designed to meet the needs of both professional landscapers and homeowners. Renowned for its efficiency and ergonomic design, this tool makes hedge trimming a more manageable and enjoyable task.

One of the standout features of the Poulan 421916 is its robust engine. Equipped with a high-performance, lightweight motor, it delivers consistent power, allowing users to handle dense and overgrown hedges effortlessly. The engine is designed for easy starting, reducing frustration during setup.

The cutting blade is another significant highlight of the Poulan 421916. It features a dual-action design that minimizes vibration during operation, providing a smooth user experience. The blades are sharpened to precision, ensuring clean cuts and promoting healthy plant growth. With a cutting capacity of around 3/4 inch, it handles thick branches with ease, offering versatility for different tasks.

In addition to its powerful engine and efficient blades, the Poulan 421916 emphasizes user comfort. It features a lightweight and well-balanced design, which reduces fatigue during extended use. The comfortable grip handles are designed to provide maximum control, allowing for precise maneuvering around landscapes of all shapes and sizes.

Safety is another crucial aspect of the Poulan 421916. It comes equipped with safety guards and a blade brake system, which halts motion when not in use. These features protect the user from accidental injuries, making it a reliable choice for anyone concerned with safety while operating power equipment.

Technologically, the Poulan 421916 utilizes advanced anti-vibration technology. This innovation considerably reduces the amount of vibration transmitted to the user's hands and arms, allowing for prolonged use without discomfort. This technology is particularly beneficial for those who may be trimming hedges for extended periods.

In summary, the Poulan 421916 is an exceptional hedge trimmer that combines power, precision, and user-friendly features. With its efficient engine, sharp dual-action blades, lightweight design, and advanced safety measures, it stands as an excellent choice for anyone looking to maintain their outdoor spaces effectively. Whether you're a professional landscaper or a homeowner, the Poulan 421916 is engineered to help you achieve neat and tidy hedges with minimal effort.
Top Page Image Contents