Poulan 961980022, 420925 owner manual KEY Part Description

Page 21

REPAIR PARTS SNOW THROWER - MODEL 961980022 (96198002200) AUGER HOUSING / IMPELLER ASSEMBLY

KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION
1	175321X479	IMPELLER
2	196710	GEARBOX ASSEMBLY
3	188909	BEARING
4	191079	IMPELLER PULLEY
5	175322	DISCHARGE BASE

6178675X008 CORNER BRACKET

7192199 CLEAN OUT TOOL

8	405400	TOOL CLIP
9	73800400	NUT 1/4−20
10	74780426	SCREW 1/4−20 X .625
11	155377	NUT 5/16−18

12163183 SCREW 5/16−18 X .625

1319111507 WASHER

1410040500 LOCKWASHER 5/16

1574940516 SCREW 5/16−18 X 1.00

16180355 CARRIAGE BOLT

17194189 SCREW 13−16 X .625

18	407760	PLUG
19	407761	GEARBOX COVER RH
20	407766	GASKET
21	407770	SEAL
22	407762	BEARING
23	174697	THRUST WASHER 1.00
24	407763	WORM GEAR
25	407764	AUGER SHAFT
26	189282	SQUARE KEY
27	407758	BEARING
28	174683	THRUST WASHER
29	407757	IMPELLER SHAFT
30	7836M	ROLL PIN
31	174681	THRUST WASHER
32	174684	THRUST BEARING
33	407769	BEARING
34	407768	O−RING

35407767 SCREW 5/16−18 X .750

36407765 GEARBOX COVER LH

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.

21

Image 21

Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Chute Deflector Remote ControlHOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONRemove Snow Thrower from Carton Unfold Upper HandleInstall Auger Control ROD See Figs Install Traction Drive Control ROD See FigsInstall Discharge Chute / Chute Rotator Head See Fig Install Chute Deflector Remote Control See FigsCheck Tire Pressure Know Your Snow Thrower OperationPrimer Ignition KEYDeflector remote control lever used to change Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerPower Steering Operation See Fig Using the CLEAN-OUT Tool See FigTo Adjust Skid Plates See Fig To Throw Snow See FigScraper BAR See Fig Before Starting the EngineCheck Engine OIL Level See Fig ADD Gasoline See FigTo Start Engine Snow Throwing TipsBefore Stopping If Recoil Starter has FrozenMaintenance Engine CleaningService and Adjustments To Adjust Snow Thrower HeightChute Deflector Remove the klik pin and remove wheel from axle To Remove Wheels See FigOther StorageTroubleshooting Exploded KEY Part Description Scrapper BAR Auger HousingCARRIAGEBOLT5/16−18X.625 Auger BearingAuger Assembly 30 RH Auger Assembly 30 LHSkid Plate LH Skid Plate RHDrift Cutter BAR Weight BARPlastic Washer Lockwasher 5/16Rotator Head LEVER/CABLE Rotator AssemblyRotator Pivot Bracket Pulley PivotChute Weldment Deflector Control AssemblyDeflector Weldment Deflector SealPlow Handle RH Plow Handle LHPanel Bracket LH Panel Bracket RH Heated Handle GripControl Lever LH Control PanelControl Lever RH Traction ROD ARMCarriage Bolt 5/16−18 X 155377 NUT 5/16−18 169675 Wire Harness Grip SwitchConsole Panel Black Headlight BezelRepair Parts Snow Thrower Model 961980022 96198002200 Drive Item 43 Exploded Drive Plate Assembly Speed Selector AssemblyEND Plate Bottom PANENGINE, TEC, Model Safety Ignition KEYFrame Engine Mount PlateBelt Cover Traction BeltImpeller Belt Wheel Assembly LH Cable Bracket LHCable Bracket RH Steering Bracket CoverPivot Bracket Wheel DriverRetainer PIN Power CordWrench Remote SpringKEY Part Limited Warranty