Poulan 420925 Install Traction Drive Control ROD See Figs, Install Auger Control ROD See Figs

Page 6

ASSEMBLY / PRE-OPERATION

INSTALL TRACTION DRIVE CONTROL ROD (See Figs. 3 and 4)

The traction drive control rod has the long loop on the end of the spring as shown.

1.Slide rubber sleeve up rod and hook end of spring into pivot bracket with loop opening down as shown.

2.With top end of rod positioned under left side of control panel, push rod down and insert top end of rod into hole in drive control bracket. Secure with retainer spring.

TRACTION DRIVE

CONTROL ROD

RUBBER

SLEEVE

LOOP

OPENING

DOWN

PIVOT

BRACKET

FIG. 3

TRACTION DRIVE

RETAINER

CONTROL LEVER

SPRING

 

TRACTION

 

DRIVE

 

CONTROL

 

ROD

DRIVE

 

CONTROL

 

BRACKET

 

FIG. 4

INSTALL AUGER CONTROL ROD (See Figs. 5 and 6)

The auger control rod has the short loop on the end of the spring as shown.

1.Slide rubber sleeve up rod and hook end of spring into control arm with loop opening up as shown.

2.With top end of rod positioned under right side of control panel, push down on rod and insert end of rod into hole in auger control bracket. Secure with retainer spring.

AUGER

CONTROL

ROD

RUBBER

SLEEVE

CONTROL

ARM

LOOP

OPENING

UP

FIG. 5

AUGER CONTROL ROD

AUGER

RETAINER

CONTROL

LEVER

SPRING

 

 

AUGER

CONTROL

BRACKET

FIG. 6

6

Image 6
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Chute Deflector Remote Control Parts Packed Separately in CartonRemove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Unfold Upper HandleInstall Traction Drive Control ROD See Figs Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotator Head See Fig Install Chute Deflector Remote Control See FigsCheck Tire Pressure Primer OperationKnow Your Snow Thrower Ignition KEYMeets A.N.S.I. Safety Requirements Deflector remote control lever used to changeHOW to USE Your Snow Thrower StoppingTo Adjust Skid Plates See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Throw Snow See FigCheck Engine OIL Level See Fig Before Starting the EngineScraper BAR See Fig ADD Gasoline See FigBefore Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has FrozenMaintenance Cleaning EngineService and Adjustments To Adjust Snow Thrower HeightChute Deflector To Remove Wheels See Fig Remove the klik pin and remove wheel from axleStorage OtherTroubleshooting Exploded KEY Part Description CARRIAGEBOLT5/16−18X.625 Auger HousingScrapper BAR Auger BearingSkid Plate LH Auger Assembly 30 LHAuger Assembly 30 RH Skid Plate RHPlastic Washer Weight BARDrift Cutter BAR Lockwasher 5/16Rotator Pivot Bracket LEVER/CABLE Rotator AssemblyRotator Head Pulley PivotDeflector Weldment Deflector Control AssemblyChute Weldment Deflector SealPanel Bracket LH Plow Handle LHPlow Handle RH Panel Bracket RH Heated Handle GripControl Lever RH Control PanelControl Lever LH Traction ROD ARMCarriage Bolt 5/16−18 X 155377 NUT 5/16−18 169675 Console Panel Black Grip SwitchWire Harness Headlight BezelRepair Parts Snow Thrower Model 961980022 96198002200 Drive Item 43 Exploded END Plate Speed Selector AssemblyDrive Plate Assembly Bottom PANFrame Safety Ignition KEYENGINE, TEC, Model Engine Mount PlateBelt Cover Traction BeltImpeller Belt Wheel Assembly LH Cable Bracket LHCable Bracket RH Pivot Bracket CoverSteering Bracket Wheel DriverWrench Power CordRetainer PIN Remote SpringKEY Part Limited Warranty