Poulan 961940007, 421102 owner manual Snow Throwing Tips, To Start Engine, Before Stopping

Page 13

OPERATION

TO START ENGINE

•Be sure fuel shut-off valve is in the “OPEN” position.

Your snow thrower engine is equipped with both a 120 Volt A.C. electric starter and a recoil starter. The electric starter is equipped with a three-wire power cord and plug and is designed to operate on 120 Volt A.C. household current.

•Be sure your house is a 120 Volt A.C. three-wire grounded system. If you are uncertain, consult a licensed electrician.

WARNING: Do not use the electric starter if your house is not a 120 Volt A.C. three-wire grounded system. Seri- ous personal injury or damage to your snow thrower could result.

COLD START - ELECTRIC STARTER

1.Insert safety ignition key (packed separately in parts bag) into ignition slot until it clicks. DO NOT turn the key. Keep the extra safety ignition key in a safe place.

2.Place throttle control in “FAST” position.

3.Rotate choke control to “FULL” position.

4.Connect the power cord to the engine.

5.Plug the other end of the power cord into a three-hole grounded 120 Volt A.C. receptacle.

6.Push the primer three (3) times.

7.Push starter button until engine starts.

IMPORTANT: Do not crank engine more than five continu- ous seconds between each time you try to start. Wait 5 to 10 seconds between each attempt.

8.When the engine starts, release the starter button and slowly move the choke control to the “OFF” position.

9.Disconnect the power cord from the receptacle first, then from the engine.

Allow the engine to warm up for a few minutes. Engine will not develop full power until it has reached normal operat- ing temperature.

WARM START - ELECTRIC STARTER

Follow the steps above, keeping the choke control in the “OFF” position.

COLD START - RECOIL STARTER

1.Insert safety ignition key (packed separately in parts bag) into ignition slot until it clicks. DO NOT turn the key. Keep the extra safety ignition key in a safe place.

2.Place throttle control in “FAST” position.

3.Rotate choke control to “FULL” position.

4.Push the primer four (4) times if the temperature is below 15°F, or two (2) times if temperature is between 15° and 50°F. If temperature is above 50°F, priming is not necessary.

NOTE: Over priming may cause flooding, preventing the engine from starting. If you do flood the engine, wait a few minutes before attempting to start and DO NOT push the primer.

5.Pull recoil starter handle quickly. Do not allow starter rope to snap back.

6.When the engine starts, release the recoil starter handle and slowly move the choke control to the “OFF” posi- tion.

Allow the engine to warm up for a few minutes. Engine will not develop full power until it has reached normal operat- ing temperature.

WARM START - RECOIL STARTER

Follow the steps above, keeping the choke in the “OFF” position. DO NOT push the primer.

BEFORE STOPPING

Run the engine for a few minutes to help dry off any mois- ture on the engine.

IF RECOIL STARTER HAS FROZEN

If the recoil starter has frozen and will not turn the engine, proceed as follows:

1.Grasp the recoil starter handle and slowly pull as much rope out of the starter as possible.

2.Release the recoil starter handle and let it snap back against the starter.

If the engine still fails to start, repeat the above steps or use the electric starter.

SNOW THROWING TIPS

•Always operate the snow thrower with the engine at full throttle. Full throttle offers the best performance.

•Go slower in deep, freezing or heavy wet snow. Use the drive speed control, NOT the throttle, to adjust speed.

•It is easier and more efficient to remove snow imme- diately after it falls.

•The best time to remove snow is the early morning. At this time the snow is usually dry and has not been ex- posed to the direct sun and warming temperatures.

•Slightly overlap each successive path to ensure all snow will be removed.

•Throw snow downwind whenever possible.

•Adjust the skid plates to proper height for current snow conditions. See “TO ADJUST SKID PLATES” in this section of this manual.

•For extremely heavy snow, reduce the width of snow removal by overlapping previous path and moving slowly.

•Keep engine clean and clear of snow during use. This will help air flow and extend engine life.

•After snow-throwing is completed, allow engine to run for a few minutes to melt snow and ice off the engine.

•Clean the entire snow thrower thoroughly after each use and wipe dry so it is ready for next use.

WARNING: Do not operate snow thrower if weather conditions impair vis- ibility. Throwing snow during a heavy, windy snowstorm can blind you and be hazardous to the safe operation of the snow thrower.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Chute Deflector Remote ControlHOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONRemove Snow Thrower from Carton Unfold Upper HandleInstall Auger Control ROD See Figs Install Traction Drive Control ROD See FigsInstall Chute Deflector Remote Control See Figs Install Discharge Chute / Chute Rotater Head See FigCheck Tire Pressure Know Your Snow Thrower OperationPrimer Ignition KEYRecoil auxiliary starter handle used for starting engine Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerPower Steering Operation See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig To Move Forward and Backward See FigBefore Starting the Engine To Adjust Skid Plates See FigCheck Engine OIL Level See Fig ADD Gasoline See FigTo Start Engine Snow Throwing TipsBefore Stopping If Recoil Starter has FrozenGeneral Recommendations MaintenanceBefore Each USE LubricationSnow Thrower CleaningEngine To Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See FigTo Replace Belts See Fig Other StorageTroubleshooting Exploded KEY Part Description Auger Assembly 30 LH Auger HousingAuger Assembly 30 RH Scrapper BARBearing Plug Auger BearingChute Weldment Deflector Control AssemblyDeflector Weldment Deflector SealRotator Head LEVER/CABLE Rotator AssemblyRotator Pivot Bracket Pulley PivotLoop Handle LH 419798X479Knob RED SpacerHandle Knob Washer 3/8Traction ROD Assembly Impeller ROD AssemblyShifter ROD TOP Shifter ROD BottomLower Handle Wire HarnessPivot Support Weldment Console PanelRepair Parts Snow Thrower Model 961940007 96194000700 Drive Drive Plate Assembly Speed Selector AssemblyEND Plate Bottom PAN01.03.002-A LH358SA-159628A KEY Part Description Tecumseh Engine Model417014X428 Engine Mount Plate Traction Belt Belt CoverImpeller Belt Wheel Driver Retainer Ring CoverWheel Lobe Clutch SlideCable Bracket RH Cable Bracket LH35062 Safety Ignition KEYDECAL, Danger 181037Service Notes HOP Limited Warranty

961940007, 421102 specifications

The Poulan 421102/961940007 is a robust and versatile chainsaw, ideal for both professional and amateur users alike. Designed to handle various cutting needs, from pruning and trimming to felling small trees, this chainsaw is known for its combination of power, ease of use, and durability.

One of the standout features of the Poulan 421102 is its high-performance engine. It typically boasts a 42cc engine that offers ample power to tackle tough cutting tasks. This engine is designed for efficiency, ensuring that users can work for extended periods without excessive fuel consumption. Moreover, the engine's design supports quick starts and smooth operation, making it a reliable choice for users of all experience levels.

The chainsaw features a lightweight and ergonomic design, providing comfort during prolonged use. Its balanced weight distribution allows for easier handling, reducing strain on the user’s arms and wrists. Coupled with an adjustable handle, this chainsaw offers excellent maneuverability, making it ideal for reaching high branches or navigating around obstacles.

Another important aspect of the Poulan 421102 is its safety features. The chainsaw often comes equipped with a chain brake that helps prevent accidents during use. The quick-stop chain brake ensures that the chain can be halted instantly in emergency situations. Additionally, the chainsaw may feature a throttle lockout, preventing accidental engagement of the throttle when not in use.

The Poulan 421102 chain system is designed for efficiency. It utilizes a 16-inch guide bar, which is optimal for residential tasks and light commercial work. The chain tensioning system allows for quick adjustments, ensuring that the chain operates smoothly, which reduces wear and extends the life of the chainsaw.

For ease of maintenance, the Poulan 421102 includes a tool-less air filter for simple cleaning and replacement. Keeping the engine clean is crucial for maintaining optimal performance and longevity. The low-vibration technology integrated into the design also contributes to user comfort and reduces fatigue, making it a great choice for longer jobs.

In summary, the Poulan 421102/961940007 chainsaw is a well-rounded tool that combines power, safety, and user-friendly features. Whether you're pruning your garden or tackling more demanding jobs, this chainsaw offers the performance needed to get the job done efficiently. Its thoughtful design and technological advancements make it a worthy investment for anyone in need of a reliable cutting tool.
Top Page Image Contents