Poulan 961940007, 421102 Cover, Wheel Driver Retainer Ring, Wheel Lobe, Clutch Slide, Axle Lobe

Page 35

REPAIR PARTS SNOW THROWER - MODEL 961940007 (96194000700) WHEELS

														2
								17					3	2
						20		17		23		4	3	1
						20			19		6	5
						16					6	5
				17	18	16				22	7
						15	18			22	7
						15	18			9	8
				16		24				10
				20		23		21		11
				19		22
				19						12
				21						12
										14
								14 13		13
						11		14 13
					10			12
2				8	9
2				7
	3	4	5	6
2	1 01.15.001-A
				KEY	PART				DESCRIPTION
				NO.	NO.				DESCRIPTION
				1	405161				COVER
				2	184471				SHOULDER SCREW

312000045 RETAINER RING

4192126 WHEEL DRIVER

5182466 RETAINER RING

6	187622	WHEEL LOBE
7	194941	CLUTCH SLIDE
8	179139	SPRING
9	189282	SQUARE KEY
10	194940	AXLE LOBE
11	174697	THRUST WASHER

12193506X479 STEERING YOKE

13179148X479 STEERING BRACKET

1417490508 SCREW 5/16−18 X .50

15194943X008 PIVOT BRACKET

16194944X008 BELLCRANK

17181847 BELLCRANK PIN

1817600406 SCREW 1/4−20 X .375

19405077 STEERING LINK

20	700279	RETAINER
21	85179	RETAINER
22	193885	SPRING
23	182015	LEVER PIN
24	194939X008	PIVOT BRACKET

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.

35

Image 35

Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Chute Deflector Remote ControlUnfold Upper Handle Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from CartonInstall Auger Control ROD See Figs Install Traction Drive Control ROD See FigsCheck Tire Pressure Install Discharge Chute / Chute Rotater Head See FigInstall Chute Deflector Remote Control See Figs Ignition KEY OperationKnow Your Snow Thrower PrimerRecoil auxiliary starter handle used for starting engine Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Throw Snow See FigADD Gasoline See Fig To Adjust Skid Plates See FigBefore Starting the Engine Check Engine OIL Level See FigIf Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before StoppingLubrication MaintenanceGeneral Recommendations Before Each USEEngine CleaningSnow Thrower Shear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Replace Belts See Fig Other StorageTroubleshooting Exploded KEY Part Description Scrapper BAR Auger HousingAuger Assembly 30 LH Auger Assembly 30 RHBearing Plug Auger BearingDeflector Seal Deflector Control AssemblyChute Weldment Deflector WeldmentPulley Pivot LEVER/CABLE Rotator AssemblyRotator Head Rotator Pivot BracketLoop Handle LH 419798X479Washer 3/8 SpacerKnob RED Handle KnobShifter ROD Bottom Impeller ROD AssemblyTraction ROD Assembly Shifter ROD TOPConsole Panel Wire HarnessLower Handle Pivot Support WeldmentRepair Parts Snow Thrower Model 961940007 96194000700 Drive Bottom PAN Speed Selector AssemblyDrive Plate Assembly END Plate 01.03.002-A 417014X428 Engine Mount Plate KEY Part Description Tecumseh Engine ModelLH358SA-159628A Impeller Belt Belt CoverTraction Belt Clutch Slide CoverWheel Driver Retainer Ring Wheel LobeCable Bracket RH Cable Bracket LH35062 Safety Ignition KEYDECAL, Danger 181037Service Notes HOP Limited Warranty