Poulan 421102, 961940007 owner manual Safe Operation Practices for Walk-Behind Snow Throwers

Page 2

IMPORTANT

Safe Operation Practices for Walk-Behind Snow Throwers

This snow thrower is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury.

Look for this symbol to point out im- portant safety precautions. It means CAUTION!!! BECOME ALERT!!! YOUR SAFETY IS INVOLVED.

WARNING: Always disconnect spark plug wire and place it where it cannot contact plug in order to prevent acci- dental starting when setting up, trans- porting, adjusting or making repairs.

WARNING: This snow thrower is for use on sidewalks, driveways and other ground level surfaces. Caution should be exercised while using on sloping sur- faces. Do not use snow thrower on surfaces above ground level such as roofs of residences, garages, porches or other such structures or buildings.

WARNING: Snow throwers have ex- posed rotating parts, which can cause severe injury from contact, or from ma- terial thrown from the discharge chute. Keep the area of operation clear of all persons, small children and pets at all times including startup.

CAUTION: Muffler and other engine parts become extremely hot during operation and remain hot after engine has stopped. To avoid severe burns on contact, stay away from these areas.

WARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemi- cals known to the State of California to cause cancer and birth defects or other reproductive harm.

Training

1.Read, understand and follow all instructions on the machine and in the manual(s) before operating this unit. Be thoroughly familiar with the controls and the proper use of the equipment. Know how to stop the unit and disengage the controls quickly.

2.Never allow children to operate the equipment. Never allow adults to operate the equipment without proper instruction.

3.Keep the area of operation clear of all persons, par- ticularly small children.

4.Exercise caution to avoid slipping or falling, especially when operating the snow thrower in reverse.

Preparation

1.Thoroughly inspect the area where the equipment is to be used and remove all doormats, sleds, boards, wires, and other foreign objects.

2.Disengage all clutches and shift into neutral before starting the engine (motor).

3.Do not operate the equipment without wearing adequate winter garments. Avoid loose fitting clothing that can get caught in moving parts. Wear footwear that will improve footing on slippery surfaces.

4.Handle fuel with care; it is highly flammable

(a)Use an approved fuel container.

(b)Never add fuel to a running engine or hot en- gine.

(c)Fill fuel tank outdoors with extreme care. Never fill fuel tank indoors.

(d)Never fill containers inside a vehicle or on a truck or trailer bed with a plastic liner. Always place containers on the ground, away from your vehicle, before filling.

(e)When practical, remove gas-powered equipment from the truck or trailer and refuel it on the ground. If this is not possible, then refuel such equipment on a trailer with a portable container, rather than from a gasoline dispenser nozzle.

(f)Keep the nozzle in contact with the rim of the fuel tank or container opening at all times, until refuel- ing is complete. Do not use a nozzle lock-open device.

(g)Replace gasoline cap securely and wipe up spilled fuel.

(h)If fuel is spilled on clothing, change clothing im- mediately.

5.Use extension cords and receptacles as specified by the manufacturer for all units with electric drive motors or electric starting motors.

6.Adjust the collector housing height to clear gravel or crushed rock surface.

7.Never attempt to make any adjustments while the engine (motor) is running (except when specifically recommended by manufacturer).

8.Always wear safety glasses or eye shields during op- eration or while performing an adjustment or repair to protect eyes from foreign objects that may be thrown from the machine.

Operation

1.Do not put hands or feet near or under rotating parts. Keep clear of the discharge opening at all times.

2.Exercise extreme caution when operating on or cross- ing gravel drives, walks, or roads. Stay alert for hidden hazards or traffic.

3.After striking a foreign object, stop the engine (motor), remove the wire from the spark plug, disconnect the cord on electric motors, thoroughly inspect the snow thrower for any damage, and repair the damage before restarting and operating the snow thrower.

4.If the unit should start to vibrate abnormally, stop the engine (motor) and check immediately for the cause. Vibration is generally a warning of trouble.

5.Stop the engine (motor) whenever you leave the oper- ating position, before unclogging the collector/impeller housing or discharge chute, and when making any

2

repairs, adjustments or inspections.

 

Page 1 Page 3
Image 2
Page 1 Page 3
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Chute Deflector Remote Control Parts Packed Separately in CartonRemove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Unfold Upper HandleInstall Traction Drive Control ROD See Figs Install Auger Control ROD See FigsCheck Tire Pressure Install Discharge Chute / Chute Rotater Head See FigInstall Chute Deflector Remote Control See Figs Primer OperationKnow Your Snow Thrower Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting engineHOW to USE Your Snow Thrower StoppingTo Throw Snow See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Move Forward and Backward See FigCheck Engine OIL Level See Fig To Adjust Skid Plates See FigBefore Starting the Engine ADD Gasoline See FigBefore Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has FrozenBefore Each USE MaintenanceGeneral Recommendations LubricationEngine CleaningSnow Thrower Chute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See FigTo Replace Belts See Fig Storage OtherTroubleshooting Exploded KEY Part Description Auger Assembly 30 RH Auger HousingAuger Assembly 30 LH Scrapper BARAuger Bearing Bearing PlugDeflector Weldment Deflector Control AssemblyChute Weldment Deflector SealRotator Pivot Bracket LEVER/CABLE Rotator AssemblyRotator Head Pulley Pivot419798X479 Loop Handle LHHandle Knob SpacerKnob RED Washer 3/8Shifter ROD TOP Impeller ROD AssemblyTraction ROD Assembly Shifter ROD BottomPivot Support Weldment Wire HarnessLower Handle Console PanelRepair Parts Snow Thrower Model 961940007 96194000700 Drive END Plate Speed Selector AssemblyDrive Plate Assembly Bottom PAN01.03.002-A 417014X428 Engine Mount Plate KEY Part Description Tecumseh Engine ModelLH358SA-159628A Impeller Belt Belt CoverTraction Belt Wheel Lobe CoverWheel Driver Retainer Ring Clutch SlideCable Bracket LH Cable Bracket RHSafety Ignition KEY 35062181037 DECAL, DangerService Notes Limited Warranty HOP

961940007, 421102 specifications

The Poulan 421102/961940007 is a robust and versatile chainsaw, ideal for both professional and amateur users alike. Designed to handle various cutting needs, from pruning and trimming to felling small trees, this chainsaw is known for its combination of power, ease of use, and durability.

One of the standout features of the Poulan 421102 is its high-performance engine. It typically boasts a 42cc engine that offers ample power to tackle tough cutting tasks. This engine is designed for efficiency, ensuring that users can work for extended periods without excessive fuel consumption. Moreover, the engine's design supports quick starts and smooth operation, making it a reliable choice for users of all experience levels.

The chainsaw features a lightweight and ergonomic design, providing comfort during prolonged use. Its balanced weight distribution allows for easier handling, reducing strain on the user’s arms and wrists. Coupled with an adjustable handle, this chainsaw offers excellent maneuverability, making it ideal for reaching high branches or navigating around obstacles.

Another important aspect of the Poulan 421102 is its safety features. The chainsaw often comes equipped with a chain brake that helps prevent accidents during use. The quick-stop chain brake ensures that the chain can be halted instantly in emergency situations. Additionally, the chainsaw may feature a throttle lockout, preventing accidental engagement of the throttle when not in use.

The Poulan 421102 chain system is designed for efficiency. It utilizes a 16-inch guide bar, which is optimal for residential tasks and light commercial work. The chain tensioning system allows for quick adjustments, ensuring that the chain operates smoothly, which reduces wear and extends the life of the chainsaw.

For ease of maintenance, the Poulan 421102 includes a tool-less air filter for simple cleaning and replacement. Keeping the engine clean is crucial for maintaining optimal performance and longevity. The low-vibration technology integrated into the design also contributes to user comfort and reduces fatigue, making it a great choice for longer jobs.

In summary, the Poulan 421102/961940007 chainsaw is a well-rounded tool that combines power, safety, and user-friendly features. Whether you're pruning your garden or tackling more demanding jobs, this chainsaw offers the performance needed to get the job done efficiently. Its thoughtful design and technological advancements make it a worthy investment for anyone in need of a reliable cutting tool.
Top Page Image Contents