Poulan 421064 owner manual KEY Part Description

Page 21

REPAIR PARTS SNOW THROWER - MODEL PP10530ES (96192001802)

AUGER HOUSING / IMPELLER ASSEMBLY

KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION

1175321X479 IMPELLER

2196710 GEARBOX ASSEMBLY

3	188909	BEARING
4	191079	IMPELLER PULLEY
5	175322	DISCHARGE BASE

6178675X008 CORNER BRACKET

7192199 CLEAN OUT TOOL

8	405400	TOOL CLIP
9	73800400	NUT 1/4−20
10	74780426	SCREW 1/4−20 X .625
11	155377	NUT 5/16−18

12163183 SCREW 5/16−18 X .625

1319111507 WASHER

1410040500 LOCKWASHER 5/16

1574940516 SCREW 5/16−18 X 1.00

16180355 CARRIAGE BOLT

17194189 SCREW 13−16 X .625

18	407760	PLUG
19	407761	GEARBOX COVER RH
20	407766	GASKET
21	407770	SEAL
22	407762	BEARING
23	174697	THRUST WASHER 1.00
24	407763	WORM GEAR
25	407764	AUGER SHAFT
26	189282	SQUARE KEY
27	407758	BEARING
28	174683	THRUST WASHER
29	407757	IMPELLER SHAFT
30	7836M	ROLL PIN
31	174681	THRUST WASHER
32	174684	THRUST BEARING
33	407769	BEARING
34	407768	O−RING

35407767 SCREW 5/16−18 X .750

36407765 GEARBOX COVER LH

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.

21

Image 21

Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONRemove Snow Thrower from Carton Unfold Upper HandleInstall Auger Control ROD See Figs Install Traction Drive Control ROD See FigsInstall Discharge Chute / Chute Rotater Head See Fig Install Chute Deflector Remote Control See FigsCheck Tire Pressure Know Your Snow Thrower OperationPrimer Ignition KEYRecoil auxiliary starter handle used for starting engine Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerPower Steering Operation See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig To Move Forward and Backward See FigBefore Starting the Engine To Adjust Skid Plates See FigCheck Engine OIL Level See Fig ADD Gasoline See FigTo Start Engine Snow Throwing TipsBefore Stopping If Recoil Starter has FrozenGeneral Recommendations MaintenanceBefore Each USE LubricationCleaning Snow ThrowerEngine To Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See FigTo Replace Belts See Fig Other StorageTroubleshooting Exploded KEY Part Description Scrapper BAR Auger HousingAuger Bearing Bearing PlugAuger Assembly 30 RH Auger Assembly 30 LHChute Weldment Deflector Control AssemblyDeflector Weldment Deflector SealRotator Head LEVER/CABLE Rotator AssemblyRotator Pivot Bracket Pulley PivotLoop Handle LH 419798X479Knob RED SpacerHandle Knob Washer 3/8Traction ROD Assembly Impeller ROD AssemblyShifter ROD TOP Shifter ROD BottomLower Handle Wire HarnessPivot Support Weldment Console PanelRepair Parts Snow Thrower Model PP10530ES Drive END Plate 43 420900 Drive Plate AssemblyWasher Control ARM01.03.002-A KEY Part Description Tecumseh Engine Model LH358SA-159628A417014X428 Engine Mount Plate Belt Cover Traction BeltImpeller Belt Wheel Driver Retainer Ring CoverWheel Lobe Clutch SlideCable Bracket RH Cable Bracket LH35062 Safety Ignition KEYDECAL, Danger 181037Service Notes HOP Limited Warranty