Poulan 421064 Lower Handle, Pivot Support Weldment, Console Panel, Headlight Bezel, Wire Harness

Page 29

REPAIR PARTS SNOW THROWER - MODEL PP10530ES (96192001802)

HANDLES

	KEY	PART	DESCRIPTION
	NO.	NO.	DESCRIPTION
	1	419797X479	LOWER HANDLE
2	2	405784X479	PIVOT SUPPORT WELDMENT
2	3	17490508	SCREW 5/16−18 X .50
	4	17000616	SCREW 3/8−16 X 1.00
	3
	4

01.05.002-A

7	4

	3			5
	2
				KEY	PART	DESCRIPTION
				NO.	NO.	DESCRIPTION
			1	1	182906	CONSOLE PANEL
	5	4	1	2	178668	HEADLIGHT BEZEL
6		4		3	180927	FLOOD HEADLIGHT
				3	180927	FLOOD HEADLIGHT
				4	184471	SHOULDER SCREW 10−24 X .625
				4	184471	SHOULDER SCREW 10−24 X .625
				5	175262	SCREW 10−24 X 1.25
		01.10.007-B		6	178770	WIRE HARNESS
		01.10.007-B		7	183784	BULB
				7	183784	BULB

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.

Image 29

Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONRemove Snow Thrower from Carton Unfold Upper HandleInstall Auger Control ROD See Figs Install Traction Drive Control ROD See FigsCheck Tire Pressure Install Discharge Chute / Chute Rotater Head See FigInstall Chute Deflector Remote Control See Figs Know Your Snow Thrower OperationPrimer Ignition KEYRecoil auxiliary starter handle used for starting engine Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerPower Steering Operation See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig To Move Forward and Backward See FigBefore Starting the Engine To Adjust Skid Plates See FigCheck Engine OIL Level See Fig ADD Gasoline See FigTo Start Engine Snow Throwing TipsBefore Stopping If Recoil Starter has FrozenGeneral Recommendations MaintenanceBefore Each USE LubricationEngine CleaningSnow Thrower To Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See FigTo Replace Belts See Fig Other StorageTroubleshooting Exploded KEY Part Description Scrapper BAR Auger HousingAuger Bearing Bearing PlugAuger Assembly 30 RH Auger Assembly 30 LHChute Weldment Deflector Control AssemblyDeflector Weldment Deflector SealRotator Head LEVER/CABLE Rotator AssemblyRotator Pivot Bracket Pulley PivotLoop Handle LH 419798X479Knob RED SpacerHandle Knob Washer 3/8Traction ROD Assembly Impeller ROD AssemblyShifter ROD TOP Shifter ROD BottomLower Handle Wire HarnessPivot Support Weldment Console PanelRepair Parts Snow Thrower Model PP10530ES Drive END Plate 43 420900 Drive Plate AssemblyWasher Control ARM01.03.002-A 417014X428 Engine Mount Plate KEY Part Description Tecumseh Engine ModelLH358SA-159628A Impeller Belt Belt CoverTraction Belt Wheel Driver Retainer Ring CoverWheel Lobe Clutch SlideCable Bracket RH Cable Bracket LH35062 Safety Ignition KEYDECAL, Danger 181037Service Notes HOP Limited Warranty

REPAIR PARTS SNOW THROWER - MODEL PP10530ES (96192001802)

KEY

LOWER HANDLE

PIVOT SUPPORT WELDMENT

KEY

CONSOLE PANEL

HEADLIGHT BEZEL

FLOOD HEADLIGHT

WIRE HARNESS

BULB