Poulan 421064 Chute Weldment, Deflector Weldment, Deflector Control Assembly, Deflector Seal

Page 24

REPAIR PARTS SNOW THROWER - MODEL PP10530ES (96192001802)

CONTROL PANEL / DISCHARGE CHUTE

5

7

3

14

15

			*13	*10
				*10
				*9
			2	*8
				*8
KEY	PART		4	6
			4
		DESCRIPTION
NO.	NO.	DESCRIPTION
1	404770X428	CHUTE WELDMENT
2	178633X428	DEFLECTOR WELDMENT	6	*12
3	420673	DEFLECTOR CONTROL ASSEMBLY		*12
4	420325	DEFLECTOR SEAL	1
5	414280	KNOB BLACK	1
5	414280	KNOB BLACK		*11
6	128415	POP RIVET		*11
6	128415	POP RIVET
7	17501010	SCREW 10−24 X .625
*8	179829	SHOULDER SCREW
*9	179246	PLASTIC WASHER		01.09.002-B
*10	191730	NUT 1/4−20		01.09.002-B
*10	191730	NUT 1/4−20
*11	72250505	CARRIAGE BOLT 5/16−18 X .50
*12	751153	NUT 5/16−18
*13	184505	DEFLECTOR SPRING

14420679 (SERVICE PART) DEFLECTOR CONTROL HEAD

15420672 (SERVICE PART) DEFLECTOR CONTROL CABLE

NOTE:

1.ALL ITEMS INDICATED WITH AN * ARE PROVIDED IN THE BAG OF ITEMS SHIPPED LOOSE WITH PRODUCT.

2.ITEMS 14 AND 15 ARE SERVICE PART NUMBERS TO ALLOW PURCHASE OF INDIVIDUAL ITEMS IF NECESSARY.

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.

24

Image 24

Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerRemove Snow Thrower from Carton Unfold Upper HandleInstall Traction Drive Control ROD See Figs Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotater Head See Fig Install Chute Deflector Remote Control See FigsCheck Tire Pressure Operation Know Your Snow ThrowerPrimer Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting engineHOW to USE Your Snow Thrower StoppingUsing the CLEAN-OUT Tool See Fig Power Steering Operation See FigTo Throw Snow See Fig To Move Forward and Backward See FigTo Adjust Skid Plates See Fig Before Starting the EngineCheck Engine OIL Level See Fig ADD Gasoline See FigSnow Throwing Tips To Start EngineBefore Stopping If Recoil Starter has FrozenMaintenance General RecommendationsBefore Each USE LubricationCleaning Snow ThrowerEngine Service and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See FigTo Replace Belts See Fig Storage OtherTroubleshooting Exploded KEY Part Description Auger Housing Scrapper BARAuger Bearing Bearing PlugAuger Assembly 30 LH Auger Assembly 30 RHDeflector Control Assembly Chute WeldmentDeflector Weldment Deflector SealLEVER/CABLE Rotator Assembly Rotator HeadRotator Pivot Bracket Pulley Pivot419798X479 Loop Handle LHSpacer Knob REDHandle Knob Washer 3/8Impeller ROD Assembly Traction ROD AssemblyShifter ROD TOP Shifter ROD BottomWire Harness Lower HandlePivot Support Weldment Console PanelRepair Parts Snow Thrower Model PP10530ES Drive 43 420900 Drive Plate Assembly END PlateWasher Control ARM01.03.002-A KEY Part Description Tecumseh Engine Model LH358SA-159628A417014X428 Engine Mount Plate Belt Cover Traction BeltImpeller Belt Cover Wheel Driver Retainer RingWheel Lobe Clutch SlideCable Bracket LH Cable Bracket RHSafety Ignition KEY 35062181037 DECAL, DangerService Notes Limited Warranty HOP