Poulan 421466 Before Starting the Engine, To Adjust Skid Plates See Fig, ADD Gasoline See Fig

Page 12

OPERATION

TO ADJUST SKID PLATES (See Fig. 17)

NOTE: The wrench provided in your parts bag may be used to adjust the skid plates.

Skid plates are located on each side of the auger housing and adjust the clearance between the scraper bar and the ground surface. Adjust skid plates evenly to proper height for current surface conditions. For removal of snow in normal conditions, such as a paved driveway or sidewalk, place skid plates in the highest position (lowest scraper clearance) to give a 1/8" clearance between the scraper bar and the ground. Use a middle position if the surface to be cleared is uneven.

NOTE: It is not recommended to operate the snow thrower over gravel or rocky surfaces. Objects such as gravel, rocks or other debris, can easily be picked up and thrown by the impeller, which can cause serious personal injury, property damage or damage to the snow thrower.

•If snow thrower must be operated over gravel surface, use extra caution and be sure skid plates are adjusted to lowest (highest scraper clearance) position.

1.Shut off engine and wait for all moving parts to stop.

2.Adjust skid plates by loosening the hex nuts, then mov- ing skid plate to desired position. Be sure both plates are adjusted evenly. Tighten securely.

HIGH POSITION

 

(LOW GROUND

 

CLEARANCE)

 

 

AUGER

 

HOUSING

 

SCRAPER BAR

HEX

SKID PLATE

NUTS

LOW POSITION (HIGH GROUND CLEARANCE)

FIG. 17

BEFORE STARTING THE ENGINE

CHECK ENGINE OIL LEVEL (See Fig. 18)

The engine on your snow thrower has been shipped, from the factory, already filled with oil.

1.Check engine oil with snow thrower on level ground.

2.Remove oil fill cap/dipstick and wipe clean, reinsert the dipstick and screw tight, wait for a few seconds, remove and read oil level. If necessary, add oil until “FULL” mark on dipstick is reached. Do not overfill.

•To change engine oil, see “TO CHANGE ENGINE OIL” in the Maintenance section of this manual.

ADD GASOLINE (See Fig. 18)

•Fill fuel tank to bottom of tank filler neck. Do not over- fill. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. Do not mix oil with gasoline. Purchase fuel in quantities that can be used within 30 days to assure fuel freshness.

WARNING: Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame.

CAUTION: Alcohol blended fuels (called gasohol or using ethanol or methanol) can at- tract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See Storage Instructions for additional information. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

SCRAPER BAR

The scraper bar is not adjustable, but is reversible. After considerable use it may become worn. When it has worn almost to the edge of the housing, it can be reversed, providing additional service before requiring replacement. Replace a damaged or worn scraper bar.

CHOKE CONTROL

SAFETY

IGNITION

KEY

RECOIL

STARTER

HANDLE

THROTTLE PRIMER ENGINE OIL FILL CAP / DIPSTICK

GASOLINE

FILLER CAP

FUEL SHUT-

OFF VALVE

12

NOTE: ALL ITEMS ARE SHOWN IN THEIR TYPICAL LOCATION. ACTUAL LOCATION MAY VARY WITH ENGINE ON YOUR UNIT.

FIG. 18

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerRemove Snow Thrower from Carton Unfold Upper HandleInstall Traction Drive Control ROD See Figs Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotator Head See Fig Install Chute Deflector Remote Control See FigsCheck Tire Pressure Operation Know Your Snow ThrowerPrimer Ignition KEYMeets A.N.S.I. Safety Requirements HOW to USE Your Snow Thrower StoppingUsing the CLEAN-OUT Tool See Fig To Move Forward and Backward See FigTo Adjust Skid Plates See Fig Before Starting the EngineCheck Engine OIL Level See Fig ADD Gasoline See FigSnow Throwing Tips To Start EngineBefore Stopping If Recoil Starter has FrozenMaintenance Cleaning EngineService and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See FigTo Replace Belts See Fig Storage Troubleshooting OtherExploded KEY Part Description Auger Housing Scrapper BARAuger 24 LH Auger 24 RHAuger Bearing Bearing PlugKnob Black POP RivetWasher Plastic WasherLEVER/CABLE Rotator Assembly Cable AssemblyRotator Head Rotator Pivot BracketSpacer RetainerKnob RED Handle KnobPanel Bracket LH Panel Bracket RH Handle GripLower Handle Pivot Support WeldmentImpeller ROD Assembly Traction ROD AssemblyShifter ROD TOP Shifter ROD Bottom183352 Console PanelDrive Speed Selector Assembly Drive Plate AssemblyShoulder Screw END PlateAxle Shaft Roll PIN 3/16Sprocket Clik PINTecumseh Engine Model FrameEngine Mount Plate Belt CoverWheel Assembly LH Safety Ignition KEY187831X421 187866X421DECAL, Danger DECAL, Poulan PRO, HP/24DECAL, DANGER, Deflector DECAL, Poulan PROLimited Warranty

421466 specifications

The Poulan 421466 is a robust and versatile chainsaw designed to meet the needs of both amateur and professional users. Renowned for its durability and efficient performance, this chainsaw is particularly suitable for various tasks, from light cutting and pruning to more demanding forestry work.

One of the most notable features of the Poulan 421466 is its powerful engine. Equipped with a reliable 42cc two-stroke gasoline engine, this chainsaw delivers impressive performance, allowing users to efficiently tackle a variety of cutting tasks. The engine is engineered for optimum power and efficiency, ensuring that users can work longer without frequent refueling.

Another significant characteristic of the Poulan 421466 is its Easy Start technology, designed to minimize the effort required to start the chainsaw. This feature is particularly beneficial for those who may struggle with starting traditional models. Users can expect a smoother and more reliable starting experience, allowing them to get to work quickly and efficiently.

The chainsaw also features an adjustable automatic oiler, which maintains proper lubrication of the chain and bar during operation. This not only enhances the longevity of the equipment but also ensures smoother cuts, as the chain remains well-lubricated even during extended use. The 16-inch bar length is ideal for various applications, providing a balanced cutting capacity that is neither too heavy nor too cumbersome.

Safety is a critical consideration for Poulan, and the 421466 includes several safety features. The chainsaw is equipped with a chain brake that automatically stops the chain in the event of kickback, reducing the risk of accidents. Additionally, the lightweight design and ergonomic handle make it easier to maneuver, reducing user fatigue during extended use.

The Poulan 421466 also boasts a user-friendly design, with features such as a tool-less chain tensioning system for easy adjustments on the go. This ensures that users can maintain optimal chain tension without the need for additional tools, streamlining the overall maintenance process.

In summary, the Poulan 421466 chainsaw combines power, efficiency, and user-friendly features, making it a solid choice for anyone in need of a reliable cutting tool. With its durable construction and advanced technologies, the Poulan 421466 stands out as a dependable partner for various cutting applications. Whether you are pruning trees in your backyard or tackling larger landscaping projects, this chainsaw is designed to get the job done efficiently and safely.
Top Page Image Contents