Poulan 421466 owner manual Table of Contents

Page 3

6.When cleaning, repairing or inspecting the snow thrower, stop the engine and make certain the collector/impeller and all moving parts have stopped. Disconnect the spark plug wire and keep the wire away from the plug to prevent someone from accidentally starting the en- gine.

7.Do not run the engine indoors, except when starting the engine and for transporting the snow thrower in or out of the building. Open the outside doors; exhaust fumes are dangerous.

8.Exercise extreme caution when operating on slopes.

9.Never operate the snow thrower without proper guards, and other safety protective devices in place and work- ing.

10.Never direct the discharge toward people or areas where property damage can occur. Keep children and others away.

11.Do not overload the machine capacity by attempting to clear snow at too fast a rate.

12.Never operate the machine at high transport speeds on slippery surfaces. Look behind and use care when operating in reverse.

13.Disengage power to the collector/impeller when snow thrower is transported or not in use.

14.Use only attachments and accessories approved by the manufacturer of the snow thrower (such as wheel weights, counterweights, or cabs).

15.Never operate the snow thrower without good visibility or light. Always be sure of your footing, and keep a firm hold on the handles. Walk; never run.

16. Never touch a hot engine or muffler.

Clearing a Clogged Discharge Chute

Hand contact with the rotating impeller inside the discharge chute is the most common cause of injury associated with snow throwers. Never use your hand to clean out the dis- charge chute. To clear the chute:

1.SHUT THE ENGINE OFF!

2.Wait 10 seconds to be sure the impeller blades have stopped rotating.

3.Always use a clean-out tool, not your hands.

Maintenance and Storage

1.Check shear bolts and other bolts at frequent intervals for proper tightness to be sure the equipment is in safe working condition.

2.Never store the machine with fuel in the fuel tank inside a building where ignition sources are present such as hot water heaters, space heaters, or clothes dryers. Allow the engine to cool before storing in any enclosure.

3.Always refer to operator’s manual for important details if the snow thrower is to be stored for an extended period.

4.Maintain or replace safety and instruction labels, as necessary.

5.Run the machine a few minutes after throwing snow to prevent freeze-up of the collector/impeller.

CONGRATULATIONS on your purchase of a new snow thrower. Ithasbeendesigned,engineeredandmanufactured to give best possible dependability and performance.

Should you experience any problem you cannot easily remedy, please contact your nearest authorized service center. We have competent, well-trained technicians and the proper tools to service or repair this unit.

Please read and retain this manual. The instructions will enable you to assemble and maintain your snow thrower properly. Always observe the “SAFETY RULES”.

SERIAL NUMBER: ___________________________

DATE OF PURCHASE: _______________________

THE MODEL AND SERIAL NUMBERS WILL BE FOUND ON A DECAL ATTACHED TO THE REAR OF THE SNOW THROWER HOUSING.

YOU SHOULD RECORD BOTH SERIAL NUMBER AND DATE OF PURCHASE AND KEEP IN A SAFE PLACE FOR FUTURE REFERENCE.

PRODUCT SPECIFICATIONS

Gasoline Capacity

2.0 Quarts (2,27 Liters)

and Type:

 

Unleaded Regular only

 

 

Oil Type

SAE 30 (above 40°F)

(API SG–SL):

SAE 5W-30 or 10W-30 (0° to +40°F)

 

SAE 0W-30 (below 0°F)

 

 

Oil Capacity:

21 Ounces (0,6 Liters)

 

 

Spark Plug:

Champion RJ19LM

Gap:

0.030" (0,762 mm)

 

 

 

CUSTOMER RESPONSIBILITIES

•Read and observe the safety rules.

•Follow a regular schedule in maintaining, caring for and using your snow thrower.

•Follow the instructions under “Maintenance” and “Stor- age” sections of this owner’s manual.

TABLE OF CONTENTS

SAFETY RULES

2-3

MAINTENANCE SCHEDULE

14

PRODUCT SPECIFICATIONS

4

SERVICE AND ADJUSTMENTS

16-18

CUSTOMER RESPONSIBILITIES

4

STORAGE

18-19

ASSEMBLY / PRE-OPERATION

5-7

TROUBLESHOOTING

19

OPERATION

8-13

REPAIR PARTS

20-35

MAINTENANCE

14-15

3 WARRANTY

36

Page 2 Page 4
Image 3
Page 2 Page 4
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Unfold Upper Handle Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from CartonInstall Auger Control ROD See Figs Install Traction Drive Control ROD See FigsInstall Discharge Chute / Chute Rotator Head See Fig Install Chute Deflector Remote Control See FigsCheck Tire Pressure Ignition KEY OperationKnow Your Snow Thrower PrimerMeets A.N.S.I. Safety Requirements Stopping HOW to USE Your Snow ThrowerTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigADD Gasoline See Fig To Adjust Skid Plates See FigBefore Starting the Engine Check Engine OIL Level See FigIf Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before StoppingMaintenance Engine CleaningShear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Replace Belts See Fig Storage Other TroubleshootingExploded KEY Part Description Auger 24 RH Auger HousingScrapper BAR Auger 24 LHBearing Plug Auger BearingPlastic Washer Knob BlackPOP Rivet WasherRotator Pivot Bracket LEVER/CABLE Rotator AssemblyCable Assembly Rotator HeadHandle Knob SpacerRetainer Knob REDPivot Support Weldment Panel Bracket LH Panel Bracket RHHandle Grip Lower HandleShifter ROD Bottom Impeller ROD AssemblyTraction ROD Assembly Shifter ROD TOPConsole Panel 183352Drive END Plate Speed Selector AssemblyDrive Plate Assembly Shoulder ScrewClik PIN Axle ShaftRoll PIN 3/16 SprocketBelt Cover Tecumseh Engine ModelFrame Engine Mount Plate187866X421 Wheel Assembly LHSafety Ignition KEY 187831X421DECAL, Poulan PRO DECAL, DangerDECAL, Poulan PRO, HP/24 DECAL, DANGER, DeflectorLimited Warranty

421466 specifications

The Poulan 421466 is a robust and versatile chainsaw designed to meet the needs of both amateur and professional users. Renowned for its durability and efficient performance, this chainsaw is particularly suitable for various tasks, from light cutting and pruning to more demanding forestry work.

One of the most notable features of the Poulan 421466 is its powerful engine. Equipped with a reliable 42cc two-stroke gasoline engine, this chainsaw delivers impressive performance, allowing users to efficiently tackle a variety of cutting tasks. The engine is engineered for optimum power and efficiency, ensuring that users can work longer without frequent refueling.

Another significant characteristic of the Poulan 421466 is its Easy Start technology, designed to minimize the effort required to start the chainsaw. This feature is particularly beneficial for those who may struggle with starting traditional models. Users can expect a smoother and more reliable starting experience, allowing them to get to work quickly and efficiently.

The chainsaw also features an adjustable automatic oiler, which maintains proper lubrication of the chain and bar during operation. This not only enhances the longevity of the equipment but also ensures smoother cuts, as the chain remains well-lubricated even during extended use. The 16-inch bar length is ideal for various applications, providing a balanced cutting capacity that is neither too heavy nor too cumbersome.

Safety is a critical consideration for Poulan, and the 421466 includes several safety features. The chainsaw is equipped with a chain brake that automatically stops the chain in the event of kickback, reducing the risk of accidents. Additionally, the lightweight design and ergonomic handle make it easier to maneuver, reducing user fatigue during extended use.

The Poulan 421466 also boasts a user-friendly design, with features such as a tool-less chain tensioning system for easy adjustments on the go. This ensures that users can maintain optimal chain tension without the need for additional tools, streamlining the overall maintenance process.

In summary, the Poulan 421466 chainsaw combines power, efficiency, and user-friendly features, making it a solid choice for anyone in need of a reliable cutting tool. With its durable construction and advanced technologies, the Poulan 421466 stands out as a dependable partner for various cutting applications. Whether you are pruning trees in your backyard or tackling larger landscaping projects, this chainsaw is designed to get the job done efficiently and safely.
Top Page Image Contents