Poulan 421466 Snow Throwing Tips, To Start Engine, Before Stopping, If Recoil Starter has Frozen

Page 13

OPERATION

TO START ENGINE

•Be sure fuel shut-off valve is in the “OPEN” position. Your snow thrower engine is equipped with a recoil starter.

COLD START

1.Insert safety ignition key (packed separately in parts bag) into ignition slot until it clicks. DO NOT turn the key. Keep the extra safety ignition key in a safe place.

2.Place throttle control in “FAST” position.

3.Rotate choke control to “FULL” position.

4.Push the primer four (4) times if the temperature is below 15°F, or two (2) times if temperature is between 15° and 50°F. If temperature is above 50°F, priming is not necessary.

NOTE: Over priming may cause flooding, preventing the engine from starting. If you do flood the engine, wait a few minutes before attempting to start and DO NOT push the primer.

5.Pull recoil starter handle quickly. Do not allow starter rope to snap back.

6.When the engine starts, release the recoil starter handle and slowly move the choke control to the “OFF” posi- tion.

Allow the engine to warm up for a few minutes. Engine will not develop full power until it has reached normal operat- ing temperature.

WARM START

Follow the steps above, keeping the choke in the “OFF” position. DO NOT push the primer.

BEFORE STOPPING

Run the engine for a few minutes to help dry off any mois- ture on the engine.

IF RECOIL STARTER HAS FROZEN

If the recoil starter has frozen and will not turn the engine, proceed as follows:

1.Grasp the recoil starter handle and slowly pull as much rope out of the starter as possible.

2.Release the recoil starter handle and let it snap back against the starter.

If the engine still fails to start, repeat the above steps.

SNOW THROWING TIPS

•Always operate the snow thrower with the engine at full throttle. Full throttle offers the best performance.

•Go slower in deep, freezing or heavy wet snow. Use the drive speed control, NOT the throttle, to adjust speed.

•It is easier and more efficient to remove snow imme- diately after it falls.

•The best time to remove snow is the early morning. At this time the snow is usually dry and has not been ex- posed to the direct sun and warming temperatures.

•Slightly overlap each successive path to ensure all snow will be removed.

•Throw snow downwind whenever possible.

•Adjust the skid plates to proper height for current snow conditions. See “TO ADJUST SKID PLATES” in this section of this manual.

•For extremely heavy snow, reduce the width of snow removal by overlapping previous path and moving slowly.

•Keep engine clean and clear of snow during use. This will help air flow and extend engine life.

•After snow-throwing is completed, allow engine to run for a few minutes to melt snow and ice off the engine.

•Clean the entire snow thrower thoroughly after each use and wipe dry so it is ready for next use.

WARNING: Do not operate snow thrower if weather conditionsimpair vis- ibility. Throwing snow during a heavy, windy snowstorm can blind you and be hazardous to the safe operation of the snow thrower.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONRemove Snow Thrower from Carton Unfold Upper HandleInstall Auger Control ROD See Figs Install Traction Drive Control ROD See FigsInstall Chute Deflector Remote Control See Figs Install Discharge Chute / Chute Rotator Head See FigCheck Tire Pressure Know Your Snow Thrower OperationPrimer Ignition KEYMeets A.N.S.I. Safety Requirements Stopping HOW to USE Your Snow ThrowerTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigBefore Starting the Engine To Adjust Skid Plates See FigCheck Engine OIL Level See Fig ADD Gasoline See FigTo Start Engine Snow Throwing TipsBefore Stopping If Recoil Starter has FrozenMaintenance Engine CleaningTo Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See FigTo Replace Belts See Fig Storage Other TroubleshootingExploded KEY Part Description Scrapper BAR Auger HousingAuger 24 LH Auger 24 RHBearing Plug Auger BearingPOP Rivet Knob BlackWasher Plastic WasherCable Assembly LEVER/CABLE Rotator AssemblyRotator Head Rotator Pivot BracketRetainer SpacerKnob RED Handle KnobHandle Grip Panel Bracket LH Panel Bracket RHLower Handle Pivot Support WeldmentTraction ROD Assembly Impeller ROD AssemblyShifter ROD TOP Shifter ROD BottomConsole Panel 183352Drive Drive Plate Assembly Speed Selector AssemblyShoulder Screw END PlateRoll PIN 3/16 Axle ShaftSprocket Clik PINFrame Tecumseh Engine ModelEngine Mount Plate Belt CoverSafety Ignition KEY Wheel Assembly LH187831X421 187866X421DECAL, Poulan PRO, HP/24 DECAL, DangerDECAL, DANGER, Deflector DECAL, Poulan PROLimited Warranty

421466 specifications

The Poulan 421466 is a robust and versatile chainsaw designed to meet the needs of both amateur and professional users. Renowned for its durability and efficient performance, this chainsaw is particularly suitable for various tasks, from light cutting and pruning to more demanding forestry work.

One of the most notable features of the Poulan 421466 is its powerful engine. Equipped with a reliable 42cc two-stroke gasoline engine, this chainsaw delivers impressive performance, allowing users to efficiently tackle a variety of cutting tasks. The engine is engineered for optimum power and efficiency, ensuring that users can work longer without frequent refueling.

Another significant characteristic of the Poulan 421466 is its Easy Start technology, designed to minimize the effort required to start the chainsaw. This feature is particularly beneficial for those who may struggle with starting traditional models. Users can expect a smoother and more reliable starting experience, allowing them to get to work quickly and efficiently.

The chainsaw also features an adjustable automatic oiler, which maintains proper lubrication of the chain and bar during operation. This not only enhances the longevity of the equipment but also ensures smoother cuts, as the chain remains well-lubricated even during extended use. The 16-inch bar length is ideal for various applications, providing a balanced cutting capacity that is neither too heavy nor too cumbersome.

Safety is a critical consideration for Poulan, and the 421466 includes several safety features. The chainsaw is equipped with a chain brake that automatically stops the chain in the event of kickback, reducing the risk of accidents. Additionally, the lightweight design and ergonomic handle make it easier to maneuver, reducing user fatigue during extended use.

The Poulan 421466 also boasts a user-friendly design, with features such as a tool-less chain tensioning system for easy adjustments on the go. This ensures that users can maintain optimal chain tension without the need for additional tools, streamlining the overall maintenance process.

In summary, the Poulan 421466 chainsaw combines power, efficiency, and user-friendly features, making it a solid choice for anyone in need of a reliable cutting tool. With its durable construction and advanced technologies, the Poulan 421466 stands out as a dependable partner for various cutting applications. Whether you are pruning trees in your backyard or tackling larger landscaping projects, this chainsaw is designed to get the job done efficiently and safely.
Top Page Image Contents