Poulan PO927ES To Remove Wheels See Fig, Remove the klik pin and remove wheel from axle

Page 17

SERVICE AND ADJUSTMENTS

WARNING: Belt replacement requires separation of the snow thrower. While separating the auger housing from the frame assembly, it is important that an assistant stand in the operating position and hold the snow thrower handles. Se- rious personal injury and/or damage to the unit could occur if the snow thrower should fall during the belt changing process.

FRAME

AUGER

ASSEMBLY

HOUSING

HANDLES

1.REMOVE GASOLINE FROM FUEL TANK - Drain gaso- line from fuel tank into a suitable container, outdoors, away from fire or flame. Wipe up any spilled gasoline.

2.REMOVE DISCHARGE CHUTE - Loosen locknut securing chute rotator head to mounting bracket only enough to allow chute rotator head to be raised and discharge chute to be removed from snow thrower.

3.REMOVE BELT COVER - See “TO REMOVE BELT COVER” in this section of this manual.

4.REMOVE ENGINE PULLEY - Remove bolt, lockwasher and flat washer securing pulley to engine crankshaft. Remove outside (auger) pulley only from crankshaft.

5.SEPARATE SNOW THROWER - With your assistant standing in the operating position holding the handles, remove the two (2) bolts and lock washers holding auger housing and frame together.

WARNING: As the last bolt is removed, have your assistant carefully lower the handles down to the ground.

6.REMOVE AUGER BELT from around pulley.

7.RELIEVETENSIONONTRACTIONDRIVEBELTIDLER and remove traction drive belt from around pulleys.

HINT: Insert a 3/8" drive ratchet (in the “ON” position) into the square hole in idler arm and rotate ratchet clockwise to relieve tension.

8.With tension relieved on idler, install new traction drive belt around pulleys and inside belt keepers.

9.Place auger belt around and inside the groove of auger pulley only.

10.While your assistant slowly raises handles to rejoin the auger housing and frame assembly, pull up on the auger belt and squeeze sides together above pulley so belt is fully seated in groove of pulley.

11.Bring snow thrower completely together and check carefully for proper routing of belts. If auger belt has become dislodged from the pulley (by catching the idler arm bracket while bringing snow thrower together), separate the snow thrower and repeat step 10. Belt must be fully seated in pulley groove when bringing

the snow thrower together.

17

12.Install the two (2) hex bolts and lock washers and tighten securely.

13.INSTALL ENGINE PULLEY - Place belt in pulley groove and slide pulley on crankshaft. Install flat washer, lock- washer and bolt and tighten securely (30-35 ft. lbs. torque). Make sure belt is inside belt keeper.

14.INSTALL BELT COVER and two (2) screws. Tighten securely.

15.INSTALL DISCHARGE CHUTE – See “INSTALL DIS- CHARGE CHUTE / CHUTE ROTATER HEAD” in the Assembly / Pre-Operation section of this manual.

 

BELT KEEPER

 

 

 

TRACTION DRIVE BELT

 

 

ENGINE

FLAT WASHER

 

PULLEY

 

 

 

 

 

LOCKWASHER

 

 

BOLT

IDLER ARM

 

 

AUGER

SQUARE

 

 

BELT

HOLE

 

 

 

CLUTCHING

 

 

IDLER ARM

 

 

BRACKET

 

 

 

AUGER PULLEY

 

 

 

 

BOLT

LOCK

 

 

 

WASHER

FRAME

AUGER

 

 

HOUSING

 

 

FIG. 23

TO REMOVE WHEELS (See Fig. 24)

Remove the klik pin and remove wheel from axle.

IMPORTANT: When installing wheel, be sure to use the axle hole closest to the end of the shaft – do not use the hole in the wheel hub (if equipped). Inner hole in axle and hole in wheel hub are not used for your model snow thrower.

NOTE: To seal punctures or prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

KLIK PIN (INSTALL

OUTER HOLE

IN OUTER HOLE

 

OF AXLE ONLY)

 

AXLE

WHEEL

WHEEL HUB

FIG. 24

Image 17
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONRemove Snow Thrower from Carton Unfold Upper HandleInstall Auger Control ROD See Figs Install Traction Drive Control ROD See FigsCheck Tire Pressure Install Discharge Chute / Chute Rotater Head See FigInstall Chute Deflector Remote Control See Figs Know Your Snow Thrower OperationPrimer Ignition KEYDeflector remote control lever used to change Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerPower Steering Operation See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig To Move Forward and Backward See FigTo Start Engine Before Starting the EngineScraper BAR If Recoil Starter has Frozen Snow Throwing TipsBefore Stopping Maintenance Engine CleaningChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Remove the klik pin and remove wheel from axle To Remove Wheels See FigOther StorageTroubleshooting Limited Warranty

PO927ES specifications

The Poulan PO927ES is a powerful and efficient gas-powered snow blower designed to tackle a variety of winter weather conditions. This robust machine combines innovative technology with user-friendly features, making it an ideal choice for homeowners needing to keep their driveways, sidewalks, and other outdoor areas clear of snow.

One of the key features of the PO927ES is its 27-inch clearing width, allowing for substantial snow removal in fewer passes. This makes it perfect for both light and heavy snowfall, ensuring efficiency during winter storms. Additionally, the 12-inch intake height enables the snow blower to handle deeper accumulations, making it suitable for different snowfall conditions.

The Poulan PO927ES is powered by a reliable 305cc engine, delivering ample power to slice through heavy, wet snow with ease. Its recoil start system ensures that users can quickly power on the machine, so they can get to work without delay. This dependable engine provides enough torque to clear even the densest snow, ensuring smooth performance throughout the winter season.

Equipped with a two-stage snow clearing system, the PO927ES efficiently discharges snow through a high-throw chute. The adjustable chute allows users to control the direction and distance of snow discharge, with a range of up to 30 feet. This feature is particularly advantageous in reducing snow mounds and ensuring that cleared areas remain accessible.

User comfort has been prioritized in the design of the PO927ES. The machine features heated hand grips, allowing for prolonged use in cold weather without discomfort. Additionally, its ergonomic controls and easy-to-navigate dashboard put the power of snow removal right at the fingertips of the user.

The snow blower also boasts heavy-duty steel construction, providing durability and longevity. The rugged build is designed to withstand the rigors of snowy conditions, ensuring that it remains a reliable tool for many winters to come.

Furthermore, the Poulan PO927ES is built with an adjustable and self-propelled drive system. This means users can select their preferred speed and power through varying terrain with confidence. The large, rugged tires enhance traction, ensuring stability and control during operation.

In conclusion, the Poulan PO927ES blends power, efficiency, and user-friendliness into a robust snow removal solution. Its impressive features, reliable engine, and thoughtful design make it a go-to choice for homeowners dealing with winter's challenges. Whether it's light flurries or heavy snowfalls, this snow blower rises to the occasion, ensuring that outdoor spaces remain safe and accessible throughout the cold months.