Poulan PO927ES Service and Adjustments, To Adjust Snow Thrower Height, Chute Deflector

Page 16

SERVICE AND ADJUSTMENTS

WARNING: To avoid serious injury, before performing any service or adjustments:

1.Be sure throttle is in STOP position.

2.Remove safety ignition key.

3.Make sure the augers and all moving parts have completely stopped.

4.Disconnect spark plug wire from spark plug and place wire where it cannot contact plug.

SNOW THROWER

TO ADJUST SNOW THROWER HEIGHT

See “TO ADJUST SKID PLATES” and “SCRAPER BAR” in the Operation section of this manual.

CHUTE DEFLECTOR

The chute deflector, attached to the top of the discharge chute, is provided to direct discharging snow away from the operator. If the deflector becomes damaged, it should be replaced.

WARNING: To avoid serious injury, never operate your snow thrower with the deflector removed or damaged.

•To change direction and/or distance snow is discharged, see “TO CONTROL SNOW DISCHARGE” in the Op- eration section of this manual.

SHEAR BOLTS (See Fig. 21)

AUGER SHEAR BOLTS

Both right and left-hand augers are secured to the auger shaft with a shoulder/shear bolt and hex nut. Should a for- eign object or ice become lodged in the augers, the shear bolts are designed to break, preventing damage to any other components. If one or both augers do not turn when auger control lever is engaged, check to see if one or both of the bolts have sheared. To replace the shear bolts:

1.Disengage all controls and move throttle control to STOP position. Wait for all moving parts to stop.

2.Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

3.Align hole in auger hub with hole in auger shaft and install a new 1/4-20 x 2" shoulder/shear bolt. Install 1/4-20 lock nut and tighten securely.

CAUTION: Do not substitute. Use only original equipment shear bolts as supplied with your snow thrower.

4.Connect spark plug wire to spark plug.

IMPELLER SHEAR BOLTS

The impeller is secured to the impeller shaft with two (2) capscrew/shear bolts and hex nuts. Should a foreign object or ice become lodged in the impeller, the capscrews are designed to break, preventing damage to any other com- ponents. If impeller does not turn when auger control lever is engaged, check to see if the capscrews have sheared. To replace the capscrew/shear bolts:

1.Disengage all controls and move throttle control to STOP position. Wait for all moving parts to stop.

2.Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

3.Align holes in impeller hub with holes in impeller shaft and install two (2) new 1/4-20 x 1-5/8" capscrew/shear bolts. Install 1/4-20 locknuts and tighten securely.

CAUTION: Do not substitute. Use only original equipment capscrew/shear bolts as supplied with your snow thrower.

4. Connect spark plug wire to spark plug.

1/4-20

1/4-20 x 1-5/8

1/4-20 x 2

LOCKNUT

CAPSCREW /

SHOULDER /

 

SHEAR BOLT

SHEAR BOLT

 

IMPELLER HUB

 

 

IMPELLER

 

 

SHAFT

 

 

 

AUGER

 

 

HUB

1/4-20

 

 

LOCKNUT

AUGER HUB

AUGER SHAFT

FIG. 21

TO REMOVE BELT COVER (See Fig. 22)

1.Remove the two screws securing belt cover to frame.

2.Remove belt cover.

•Replace belt cover by installing cover and screws and tighten securely.

FRAME

BELT COVER

SCREWS

FIG. 22

TO REPLACE BELTS (See Fig. 23)

The auger and traction drive belts are not adjustable. If the belts are damaged or begin to slip from wear, they should be replaced. It is recommended that the belt(s) be replaced by a qualified service center.

NOTE: It is recommended that both the auger and traction drive belt be replaced at the same time.

The V-belts on your snow thrower are of special construction and should be replaced by original equipment manufacturer (OEM) belts available from your nearest dealer. Using other than OEM belts can cause personal injury or damage to

16 the snow thrower.

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerRemove Snow Thrower from Carton Unfold Upper HandleInstall Traction Drive Control ROD See Figs Install Auger Control ROD See FigsInstall Chute Deflector Remote Control See Figs Install Discharge Chute / Chute Rotater Head See FigCheck Tire Pressure Operation Know Your Snow ThrowerPrimer Ignition KEYMeets A.N.S.I. Safety Requirements Deflector remote control lever used to changeHOW to USE Your Snow Thrower StoppingUsing the CLEAN-OUT Tool See Fig Power Steering Operation See FigTo Throw Snow See Fig To Move Forward and Backward See FigScraper BAR Before Starting the EngineTo Start Engine Before Stopping Snow Throwing TipsIf Recoil Starter has Frozen Maintenance Cleaning EngineTo Adjust Snow Thrower Height Service and AdjustmentsChute Deflector To Remove Wheels See Fig Remove the klik pin and remove wheel from axleStorage OtherTroubleshooting Limited Warranty

PO927ES specifications

The Poulan PO927ES is a powerful and efficient gas-powered snow blower designed to tackle a variety of winter weather conditions. This robust machine combines innovative technology with user-friendly features, making it an ideal choice for homeowners needing to keep their driveways, sidewalks, and other outdoor areas clear of snow.

One of the key features of the PO927ES is its 27-inch clearing width, allowing for substantial snow removal in fewer passes. This makes it perfect for both light and heavy snowfall, ensuring efficiency during winter storms. Additionally, the 12-inch intake height enables the snow blower to handle deeper accumulations, making it suitable for different snowfall conditions.

The Poulan PO927ES is powered by a reliable 305cc engine, delivering ample power to slice through heavy, wet snow with ease. Its recoil start system ensures that users can quickly power on the machine, so they can get to work without delay. This dependable engine provides enough torque to clear even the densest snow, ensuring smooth performance throughout the winter season.

Equipped with a two-stage snow clearing system, the PO927ES efficiently discharges snow through a high-throw chute. The adjustable chute allows users to control the direction and distance of snow discharge, with a range of up to 30 feet. This feature is particularly advantageous in reducing snow mounds and ensuring that cleared areas remain accessible.

User comfort has been prioritized in the design of the PO927ES. The machine features heated hand grips, allowing for prolonged use in cold weather without discomfort. Additionally, its ergonomic controls and easy-to-navigate dashboard put the power of snow removal right at the fingertips of the user.

The snow blower also boasts heavy-duty steel construction, providing durability and longevity. The rugged build is designed to withstand the rigors of snowy conditions, ensuring that it remains a reliable tool for many winters to come.

Furthermore, the Poulan PO927ES is built with an adjustable and self-propelled drive system. This means users can select their preferred speed and power through varying terrain with confidence. The large, rugged tires enhance traction, ensuring stability and control during operation.

In conclusion, the Poulan PO927ES blends power, efficiency, and user-friendliness into a robust snow removal solution. Its impressive features, reliable engine, and thoughtful design make it a go-to choice for homeowners dealing with winter's challenges. Whether it's light flurries or heavy snowfalls, this snow blower rises to the occasion, ensuring that outdoor spaces remain safe and accessible throughout the cold months.
Top Page Image Contents