Poulan 415324, 96198001900 owner manual To Replace Belts See Fig

Page 16

SERVICE AND ADJUSTMENTS

TO REPLACE BELTS (See Fig. 20)

The auger and traction drive belts are not adjustable. If the belts are damaged or begin to slip from wear, they should be replaced. It is recommended that the belt(s) be replaced by a Sears service centre/department.

NOTE: It is recommended that both the auger and traction drive belt be replaced at the same time.

The V-belts on your snow thrower are of special construction and should be replaced by original equipment manufacturer (OEM) belts available from your nearest Sears service centre/department. Using other than OEM belts can cause personal injury or damage to the snow thrower.

WARNING: Belt replacement requires separation of the snow thrower. While separating the auger housing from the frame assembly, it is important that an assistant stand in the operating position and hold the snow thrower handles. Serious personal injury and/or damage to the unit could occur if the snow thrower should fall during the belt changing process.

FRAME

AUGER

ASSEMBLY

HOUSING

HANDLES

1.REMOVE GASOLINE FROM FUEL TANK - Drain gasoline from fuel tank into a suitable container, out- doors, away from fire or flame. Wipe up any spilled gasoline.

2.REMOVE DISCHARGE CHUTE - Loosen locknut securing chute rotator head to mounting bracket only enough to allow chute rotator head to be raised and discharge chute to be removed from snow thrower.

3.REMOVE BELT COVER - See “TO REMOVE BELT COVER” in this section of this manual.

4.REMOVE ENGINE PULLEY - Remove bolt, lockwasher and flat washer securing pulley to engine crankshaft. Remove outside (auger) pulley only from crankshaft.

5.SEPARATE SNOW THROWER - With your assistant standing in the operating position holding the handles, remove the two (2) bolts holding auger housing and frame together.

WARNING: As the last bolt is removed, have your assistant carefully lower the handles down to the ground.

6.REMOVE AUGER BELT from around pulley.

7.RELIEVE TENSION ON TRACTION DRIVE BELT IDLER and remove traction drive belt from around pulleys.

16

HINT: Insert a 3/8" drive ratchet (in the “ON” position) into the square hole in idler arm and rotate ratchet clockwise to relieve tension.

8.With tension relieved on idler, install new traction drive belt around pulleys and inside belt keepers.

9.Place auger belt around and inside the groove of auger pulley only.

10.While your assistant slowly raises handles to rejoin the auger housing and frame assembly, pull up on the auger belt and squeeze sides together above pulley so belt is fully seated in groove of pulley.

11.Bring snow thrower completely together and check carefully for proper routing of belts. If auger belt has become dislodged from the pulley (by catching the idler arm bracket while bringing snow thrower together), separate the snow thrower and repeat step 10. Belt must be fully seated in pulley groove when bringing the snow thrower together.

12.Install the two (2) hex bolts and lock washers and tighten securely.

13.INSTALL ENGINE PULLEY - Place belt in pulley groove and slide pulley on crankshaft. Install flat washer, lockwasher and bolt and tighten securely (41-47 N-m torque). Make sure belt is inside belt keeper.

14.INSTALL BELT COVER and two (2) screws. Tighten securely.

15.INSTALL DISCHARGE CHUTE – See “INSTALL DIS- CHARGE CHUTE / CHUTE ROTATER HEAD” in the Assembly / Pre-Operation section of this manual.

 

BELT KEEPER

 

 

TRACTION DRIVE BELT

 

ENGINE

FLAT WASHER

 

PULLEY

 

 

 

 

LOCKWASHER

 

 

BOLT

IDLER ARM

 

AUGER

SQUARE

 

BELT

HOLE

 

 

CLUTCHING

 

IDLER ARM

 

BRACKET

 

 

AUGER PULLEY

 

 

 

BOLTS

FRAME

AUGER

 

 

HOUSING

 

FIG. 20

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerRemove Snow Thrower from Carton Unfold Upper HandleInstall Discharge Chute / Chute Rotater Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Operation Know Your Snow ThrowerPrimer Ignition KEYRecoil auxiliary starter handle used for starting Skid PlateHOW to USE Your Snow Thrower StoppingTo USE Choke Control See Fig To Control Snow Discharge See FigsUsing the CLEAN-OUT Tool See Fig To Adjust Skid Plates See FigTo Throw Snow See Fig To Move Forward and Backward See FigBefore Starting the Engine Scraper BARCheck Engine OIL Level See Fig ADD Gasoline See FigBefore Stopping Snow Throwing TipsIf Recoil Starter has Frozen Maintenance Cleaning EngineService and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See FigTo Replace Belts See Fig Storage OtherTroubleshooting Service Notes   KEY Part Description Page 414280 Knob, Lever, Black 1724 KEY Part Description Repair Parts Drive Repair Parts Snow Thrower Model 961980019 96198001900 Drive Page KEY Part Description   KEY Part Description Limited Warranty

96198001900, 415324 specifications

The Poulan 415324,96198001900 is a powerful and reliable string trimmer designed for both homeowners and professionals alike. Its robust construction and advanced technology make it an ideal choice for tackling a wide array of landscaping tasks.

One of the standout features of the Poulan 415324 is its high-performance engine. This trimmer is equipped with a 25cc two-cycle engine that provides ample power for cutting through thick grass and weeds. The engine ensures easy starting and efficient fuel consumption, which translates into longer run times and less frequent refueling. Coupled with a lightweight design, users can maneuver the trimmer with ease, reducing fatigue during extended use.

The Poulan 415324 boasts an impressive cutting width of 17 inches. This allows users to trim large areas quickly and efficiently, making it perfect for large lawns or gardens. The dual line feed system automatically advances the trimmer line when needed, ensuring a consistent cutting performance. This feature eliminates downtime spent adjusting the line and allows users to focus on the job at hand.

Another essential characteristic of this string trimmer is its adjustable handle. The ergonomic design allows for personalized height adjustments, providing comfort while reducing strain on the arms and back. This feature is especially beneficial for users of varying heights, ensuring everyone can find a comfortable grip.

Safety is an essential aspect of the Poulan 415324's design. It comes equipped with a safety guard that protects the user from debris while trimming. This guard is not only practical but enhances the overall user experience by minimizing potential accidents.

Additionally, the Poulan 415324 incorporates advanced technologies such as easy-start technology, which reduces the amount of effort needed to start the engine. This feature is particularly useful for those who may struggle with traditional pull-start mechanisms, making it accessible for a wider range of users.

In conclusion, the Poulan 415324,96198001900 string trimmer is a versatile and efficient tool that meets the demands of both casual and serious gardening enthusiasts. With its powerful engine, wide cutting capacity, adjustable ergonomic handle, and safety features, it stands out in the market. Whether maintaining a home garden or tending to professional landscaping needs, the Poulan 415324 is a reliable choice that delivers excellent performance and ease of use.
Top Page Image Contents