Poulan 416829 owner manual Before Starting the Engine, Scraper BAR, Check Engine OIL Level See Fig

Page 11

OPERATION

TON TE:ADJUSTThe wrenchSKID PLATESprovided(Seein yourFig.parts17) bag may be

usedNOTE:to Theadjustwrenchthe skidprovidedplates. in your parts bag may be usedSkid platesto adjustarethelocatedskid plateson each. side of the auger housing andSkidadjustplatestheareclearancelocated onbeachtweensidetheofscraperthe augerbarhousingand the groundand adjustsurfacethe clearance. Adjust skidbetweenplates theevenlyscraperto properbar andheightthe forgroundcurrentsurfacesurface. Adjustcondskitionsd plates. Forevenlyremovalto properf snowheightin normalfor currentcondisurfacetions, suchconditionsas a paved. Fordrivewayremoval orofsidesnowwalk,in placenormalskidcondiplatestions,insuchthe ashighesta pavedpositiondriveway(lowestor sidescraperwalk, clearplaceance)skid platesto giveina the1/8"highestclearancepositionbetween(lowestthe scraper barclearandance)thetogroundgive a. 1/8"Use clearancemiddle positionbetweenif the scraperurface tobarbeandclearedthe groundis uneven. Use. a middle position if the surface

toNOTE:be clearedIt is notisrecommendeduneven. to operate the snow thrower

overNOTE:gravelIt is ornotrockyrecommendedsurfaces. Objectsto operatesuchtheassnowgravel,throwerrocks overothergraveldebris,or rockyansurfaceseasily be. Objectspicked upsuchandasthrowngravel,byrocksthe impeller,or other debris,which cancauseeasilyseriousbe pickedpersonalup andinjury,thrownpropertyby the damimpeller,age whichor damagecan causeto theserioussnow throwerpersonal. injury, property

dam• Ifagesnowor damagethrower mustto thebesnowoperatedthrowerover. gravel surface, use extra caution and be sure skid platesgravelare adjusted

• If snow thrower must be operated over surface, to lowest (highest scraper clearance) position.

use extra caution and be sure skid plates are adjusted

1. toShutlowestoff engine(highestandscraperwait forclearall movingance) positionparts to. stop.

WARNING: Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame.

CAUTION: Alcohol blended fuels (called gasohol or using ethanol or methanol) can at- tract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See Storage Instructions for additional information. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

12. ShutAdjustoffskidengineplatesandbywaitlooseningfor all movingthe rearparts1/2"tohexstopnut. only, then moving skid plate to desired position. Be sure

2. Adjust skid plates by loosening the hex nuts, then mov- both plates are adjusted evenly. Tighten securely. ing skid plate to desired position. Be sure both plates are adjusted evenly. Tighten securely.

SCRAPER BAR

HIGH POSITION

 

(LOW GROUND

 

CLEARANCE)

 

 

AUGER

 

HOUSING

 

SCRAPER BAR

HEX

SKID PLATE

NUTS

LOW POSITION (HIGH GROUND CLEARANCE)

FIG. 17

The scraper bar is not adjustable, but is reversible. After considerable use it may become worn. When it has worn almost to the edge of the housing, it can be reversed,

CHOKE CONTROL

SAFETY

IGNITION

KEY

RECOIL

STARTER

HANDLE

THROTTLE PRIMER ENGINE OIL FILL CAP / DIPSTICK

GASOLINE

FILLER CAP

FUEL SHUT-

OFF VALVE

STARTER BUTTON

POWER CORD PLUG

providing additional service before requiring replacement. Replace a damaged or worn scraper bar.

BEFORE STARTING THE ENGINE

CHECK ENGINE OIL LEVEL (See Fig. 18)

The engine on your snow thrower has been shipped, from the factory, already filled with oil.

1.Check engine oil with snow thrower on level ground.

2.Remove oil fill cap/dipstick and wipe clean, reinsert the dipstick and screw tight, wait for a few seconds, remove and read oil level. If necessary, add oil until “FULL” mark on dipstick is reached. Do not overfill.

•To change engine oil, see “TO CHANGE ENGINE OIL” in the Maintenance section of this manual.

ADD GASOLINE (See Fig. 18)

•Fill fuel tank to bottom of tank filler neck. Do not over- fill. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. Do not mix oil with gasoline. Purchase fuel in quantities that can be used within 30 days to assure fuel freshness.

NOTE: ALL ITEMS ARE SHOWN IN THEIR TYPICAL LOCATION. ACTUAL LOCATION MAY VARY WITH ENGINE ON YOUR UNIT.

FIG. 18

TO START ENGINE

•Be sure fuel shut-off valve is in the OPEN position.

Your snow thrower engine is equipped with both a 120 Volt A.C. electric starter and a recoil starter. The electric starter is equipped with a three-wire power cord and plug and is designed to operate on 120 Volt A.C. household current.

•Be sure your house is a 120 Volt A.C. three-wire grounded system. If you are uncertain, consult a licensed electrician.

WARNING: Do not use the electric starter if your house is not a 120 Volt A.C. three-wire grounded system. Se- rious personal injury or damage to your snow thrower could result.

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Unfold Upper Handle Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Check Tire Pressure Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotater Head See Fig Ignition KEY OperationKnow Your Snow Thrower PrimerDischarge chute control lever used to change the di Meets A.N.S.I. Safety RequirementsRecoil auxiliary starter handle used for starting Stopping HOW to USE Your Snow ThrowerTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig ADD Gasoline See Fig Before Starting the EngineScraper BAR Check Engine OIL Level See FigIf Recoil Starter has Frozen Snow Throwing TipsBefore Stopping Maintenance Engine CleaningChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height To Remove Wheels See Fig Other StorageTroubleshooting Service Notes AIG plugr1 KEY Part Description 07Chute-knob2 414280 Knob, Lever Repair Parts Snow Thrower - Model NO. PR5524ES Handles Repair Parts Snow Thrower - Model NO. PR5524ES Handles Repair Parts Snow Thrower - Model NO. PR5524ES Drive Repair Parts Snow Thrower - Model NO. PR5524ES Drive Page 417014X428 KEY Part Description416954 Page 416829 416830 181037 Decal, DangerLimited Warranty

416829 specifications

The Poulan 416829 is a high-performance chainsaw designed for both casual users and professionals seeking reliability and efficiency in outdoor tasks. With a robust build and innovative features, the Poulan 416829 stands out in the competitive landscape of gardening and landscaping equipment.

At the heart of the Poulan 416829 is its powerful engine, which typically features a displacement of around 40cc. This ensures ample cutting power for handling a variety of wood types, from softwoods to hardwoods. The two-stroke engine design enhances fuel efficiency while delivering consistent power throughout the cutting process. The design is both lightweight and compact, allowing for easy maneuverability and reduced user fatigue during extended use.

One of the standout features of the Poulan 416829 is its Easy Start technology. This system is engineered to facilitate a hassle-free starting experience, significantly reducing the effort required to start the chainsaw. Coupled with a primer bulb and adjustable choke, users can expect quick and efficient startups, making it an ideal choice for those who may be new to using chainsaws.

The cutting capacity of the Poulan 416829 is enhanced by its bar length, typically ranging around 16 to 18 inches. This substantial reach allows for tackling a variety of cutting tasks, from pruning branches to felling small trees. The Oregon chain used in this model contributes to smooth cuts and efficient debris removal, making the overall cutting experience more satisfying.

Safety is paramount in chainsaw design, and the Poulan 416829 does not fall short. It includes essential safety features such as a chain brake, which engages in case of kickback, and an anti-vibration system that minimizes vibration during operation. These safety technologies not only protect the user but also enhance comfort during use.

Durability is another key characteristic of the Poulan 416829. Constructed with high-quality materials, the chainsaw is designed to withstand the rigors of outdoor work. The air filtration system helps to prolong engine life by preventing dirt and debris from entering the engine, ensuring reliable performance over time.

In conclusion, the Poulan 416829 is a versatile and user-friendly chainsaw, equipped with powerful technology and safety features that cater to a wide range of cutting needs. Whether you are a homeowner looking to maintain your yard or a professional needing a reliable tool for your work, the Poulan 416829 provides the performance and efficiency necessary to get the job done effectively.
Top Page Image Contents