Poulan 416829 owner manual Safe Operation Practices for Walk-Behind Snow Throwers

Page 2

IMPORTANT

Safe Operation Practices for Walk-Behind Snow Throwers

This snow thrower is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury.

Look for this symbol to point out im- portant safety precautions. It means CAUTION!!! BECOME ALERT!!! YOUR SAFETY IS INVOLVED.

WARNING: Always remove safety igni- tion key and disconnect spark plug wire. Place it where it cannot contact plug in order to prevent accidental starting when setting up, transporting, adjusting or making repairs.

WARNING: This snow thrower is for use on sidewalks, driveways and other ground level surfaces. Caution should be exercised while using on sloping sur- faces. Do not use snow thrower on surfaces above ground level such as roofs of residences, garages, porches or other such structures or buildings.

WARNING: Snow throwers have ex- posed rotating parts, which can cause severe injury from contact, or from ma- terial thrown from the discharge chute. Keep the area of operation clear of all persons, small children and pets at all times including startup.

CAUTION: Muffler and other engine parts become extremely hot during operation and remain hot after engine has stopped. To avoid severe burns on contact, stay away from these areas.

WARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemi- cals known to the State of California to cause cancer and birth defects or other reproductive harm.

Training

1.Read, understand and follow all instructions on the machine and in the manual(s) before operating this unit. Be thoroughly familiar with the controls and the proper use of the equipment. Know how to stop the unit and disengage the controls quickly.

2.Never allow children to operate the equipment. Never allow adults to operate the equipment without proper instruction.

3.Keep the area of operation clear of all persons, par- ticularly small children.

4.Exercise caution to avoid slipping or falling, especially when operating the snow thrower in reverse.

Preparation

1.Thoroughly inspect the area where the equipment is to be used and remove all doormats, sleds, boards, wires, and other foreign objects.

2.Disengage all clutches and shift into neutral before starting the engine (motor).

3.Do not operate the equipment without wearing adequate winter garments. Avoid loose fitting clothing that can get caught in moving parts. Wear footwear that will improve footing on slippery surfaces.

4.Handle fuel with care; it is highly flammable

(a)Use an approved fuel container.

(b)Never add fuel to a running engine or hot en- gine.

(c)Fill fuel tank outdoors with extreme care. Never fill fuel tank indoors.

(d)Never fill containers inside a vehicle or on a truck or trailer bed with a plastic liner. Always place containers on the ground, away from your vehicle, before filling.

(e)When practical, remove gas-powered equipment from the truck or trailer and refuel it on the ground. If this is not possible, then refuel such equipment on a trailer with a portable container, rather than from a gasoline dispenser nozzle.

(f)Keep the nozzle in contact with the rim of the fuel tank or container opening at all times, until refuel- ing is complete. Do not use a nozzle lock-open device.

(g)Replace gasoline cap securely and wipe up spilled fuel.

(h)If fuel is spilled on clothing, change clothing im- mediately.

5.Use extension cords and receptacles as specified by the manufacturer for all units with electric drive motors or electric starting motors.

6.Adjust the collector housing height to clear gravel or crushed rock surface.

7.Never attempt to make any adjustments while the engine (motor) is running (except when specifically recommended by manufacturer).

8.Always wear safety glasses or eye shields during op- eration or while performing an adjustment or repair to protect eyes from foreign objects that may be thrown from the machine.

Operation

1.Do not put hands or feet near or under rotating parts. Keep clear of the discharge opening at all times.

2.Exercise extreme caution when operating on or cross- ing gravel drives, walks, or roads. Stay alert for hidden hazards or traffic.

3.After striking a foreign object, stop the engine (motor), remove the wire from the spark plug, disconnect the cord on electric motors, thoroughly inspect the snow thrower for any damage, and repair the damage before restarting and operating the snow thrower.

4.If the unit should start to vibrate abnormally, stop the engine (motor) and check immediately for the cause. Vibration is generally a warning of trouble.

5.Stop the engine (motor) whenever you leave the oper- ating position, before unclogging the collector/impeller housing or discharge chute, and when making any

2

repairs, adjustments or inspections.

 

Page 1 Page 3
Image 2
Page 1 Page 3
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Unfold Upper Handle Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Check Tire Pressure Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotater Head See Fig Primer OperationKnow Your Snow Thrower Ignition KEYDischarge chute control lever used to change the di Meets A.N.S.I. Safety RequirementsRecoil auxiliary starter handle used for starting HOW to USE Your Snow Thrower StoppingTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig Check Engine OIL Level See Fig Before Starting the EngineScraper BAR ADD Gasoline See FigIf Recoil Starter has Frozen Snow Throwing TipsBefore Stopping Maintenance Cleaning EngineChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height To Remove Wheels See Fig Storage OtherTroubleshooting Service Notes AIG plugr1 KEY Part Description 07Chute-knob2 414280 Knob, Lever Repair Parts Snow Thrower - Model NO. PR5524ES Handles Repair Parts Snow Thrower - Model NO. PR5524ES Handles Repair Parts Snow Thrower - Model NO. PR5524ES Drive Repair Parts Snow Thrower - Model NO. PR5524ES Drive Page 417014X428 KEY Part Description416954 Page 181037 Decal, Danger 416829 416830Limited Warranty

416829 specifications

The Poulan 416829 is a high-performance chainsaw designed for both casual users and professionals seeking reliability and efficiency in outdoor tasks. With a robust build and innovative features, the Poulan 416829 stands out in the competitive landscape of gardening and landscaping equipment.

At the heart of the Poulan 416829 is its powerful engine, which typically features a displacement of around 40cc. This ensures ample cutting power for handling a variety of wood types, from softwoods to hardwoods. The two-stroke engine design enhances fuel efficiency while delivering consistent power throughout the cutting process. The design is both lightweight and compact, allowing for easy maneuverability and reduced user fatigue during extended use.

One of the standout features of the Poulan 416829 is its Easy Start technology. This system is engineered to facilitate a hassle-free starting experience, significantly reducing the effort required to start the chainsaw. Coupled with a primer bulb and adjustable choke, users can expect quick and efficient startups, making it an ideal choice for those who may be new to using chainsaws.

The cutting capacity of the Poulan 416829 is enhanced by its bar length, typically ranging around 16 to 18 inches. This substantial reach allows for tackling a variety of cutting tasks, from pruning branches to felling small trees. The Oregon chain used in this model contributes to smooth cuts and efficient debris removal, making the overall cutting experience more satisfying.

Safety is paramount in chainsaw design, and the Poulan 416829 does not fall short. It includes essential safety features such as a chain brake, which engages in case of kickback, and an anti-vibration system that minimizes vibration during operation. These safety technologies not only protect the user but also enhance comfort during use.

Durability is another key characteristic of the Poulan 416829. Constructed with high-quality materials, the chainsaw is designed to withstand the rigors of outdoor work. The air filtration system helps to prolong engine life by preventing dirt and debris from entering the engine, ensuring reliable performance over time.

In conclusion, the Poulan 416829 is a versatile and user-friendly chainsaw, equipped with powerful technology and safety features that cater to a wide range of cutting needs. Whether you are a homeowner looking to maintain your yard or a professional needing a reliable tool for your work, the Poulan 416829 provides the performance and efficiency necessary to get the job done effectively.
Top Page Image Contents