Poulan 416829 owner manual To Remove Wheels See Fig

Page 16

SERVICE AND ADJUSTMENTS

WARNING: Belt replacement requires separation of the snow thrower. While separating the auger housing from the frame assembly, it is important that an assistant stand in the operating position and hold the snow thrower handles. Serious personal injury and/or damage to the unit could occur if the snow thrower should fall during the belt changing process.

FRAME

AUGER

ASSEMBLY

HOUSING

HANDLES

1.REMOVE GASOLINE FROM FUEL TANK - Drain gasoline from fuel tank into a suitable container, out- doors, away from fire or flame. Wipe up any spilled gasoline.

2.REMOVE DISCHARGE CHUTE - Loosen locknut securing chute rotator head to mounting bracket only enough to allow chute rotator head to be raised and discharge chute to be removed from snow thrower.

3.REMOVE BELT COVER - See “TO REMOVE BELT COVER” in this section of this manual.

4.REMOVE ENGINE PULLEY - Remove bolt, lockwasher and flat washer securing pulley to engine crankshaft. Remove outside (auger) pulley only from crankshaft.

5.SEPARATE SNOW THROWER - With your assistant standing in the operating position holding the handles, remove the two (2) bolts holding auger housing and frame together.

WARNING: As the last bolt is removed, have your assistant carefully lower the handles down to the ground.

6.REMOVE AUGER BELT from around pulley.

7.RELIEVETENSIONONTRACTIONDRIVEBELTIDLER and remove traction drive belt from around pulleys.

HINT: Insert a 3/8" drive ratchet (in the “ON” position) into the square hole in idler arm and rotate ratchet clockwise to relieve tension.

8.With tension relieved on idler, install new traction drive belt around pulleys and inside belt keepers.

9.Place auger belt around and inside the groove of auger pulley only.

10.While your assistant slowly raises handles to rejoin the auger housing and frame assembly, pull up on the auger belt and squeeze sides together above pulley so belt is fully seated in groove of pulley.

11.Bring snow thrower completely together and check carefully for proper routing of belts. If auger belt has become dislodged from the pulley (by catching the idler

arm bracket while bringing snow thrower together),

 

separate the snow thrower and repeat step 10. Belt

 

must be fully seated in pulley groove when bringing

16

the snow thrower together.

12.Install the two (2) hex boltsand tighten securely.

13.INSTALL ENGINE PULLEY - Place belt in pulley groove and slide pulley on crankshaft. Install flat washer, lockwasher and bolt and tighten securely (30-35 ft. lbs. torque). Make sure belt is inside belt keeper.

14.INSTALL BELT COVER and two (2) screws. Tighten securely.

15.INSTALL DISCHARGE CHUTE – See “INSTALL DIS- CHARGE CHUTE / CHUTE ROTATER HEAD” in the Assembly / Pre-Operation section of this manual.

 

BELT KEEPER

 

 

TRACTION DRIVE BELT

 

ENGINE

FLAT WASHER

 

PULLEY

 

 

 

 

LOCKWASHER

 

 

BOLT

IDLER ARM

 

AUGER

SQUARE

 

BELT

HOLE

 

 

CLUTCHING

 

IDLER ARM

 

BRACKET

 

 

AUGER PULLEY

 

 

 

BOLT

FRAME

AUGER

 

HOUSING

 

FIG. 21

TO REMOVE WHEELS (See Fig. 22)

•Remove the klik pin and remove wheel from axle.

IMPORTANT: When installing wheel, be sure to use the in- nermost hole in axle and the wheel hub hole. To disengage drive system from the wheels (for pushing or transporting the snow thrower), remove klik pin from wheel hub and insert pin into the outermost hole in axle only.

KLIK PIN

OUTER HOLE

 

INNER

 

HOLE

WHEEL

WHEEL HUB

FIG. 22

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents HOW to SET UP Your Snow Thrower Parts Packed Separately in Carton Assembly / PRE-OPERATIONRemove Snow Thrower from Carton Install Traction Drive Control ROD See Figs Install Speed Control ROD See FigsUnfold Upper Handle Install Discharge Chute / Chute Rotater Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Operation Know Your Snow ThrowerPrimer Ignition KEYRecoil auxiliary starter handle used for starting Meets A.N.S.I. Safety RequirementsDischarge chute control lever used to change the di HOW to USE Your Snow Thrower StoppingTo Throw Snow See Fig Using the CLEAN-OUT Tool See FigTo Move Forward and Backward See Fig Before Starting the Engine Scraper BARCheck Engine OIL Level See Fig ADD Gasoline See FigBefore Stopping Snow Throwing TipsIf Recoil Starter has Frozen Maintenance Cleaning EngineTo Adjust Snow Thrower Height Service and AdjustmentsChute Deflector To Remove Wheels See Fig Storage OtherTroubleshooting Service Notes AIG plugr1 KEY Part Description 07Chute-knob2 414280 Knob, Lever Repair Parts Snow Thrower - Model NO. PR5524ES Handles Repair Parts Snow Thrower - Model NO. PR5524ES Handles Repair Parts Snow Thrower - Model NO. PR5524ES Drive Repair Parts Snow Thrower - Model NO. PR5524ES Drive Page 416954 KEY Part Description417014X428 Page 181037 Decal, Danger 416829 416830Limited Warranty

416829 specifications

The Poulan 416829 is a high-performance chainsaw designed for both casual users and professionals seeking reliability and efficiency in outdoor tasks. With a robust build and innovative features, the Poulan 416829 stands out in the competitive landscape of gardening and landscaping equipment.

At the heart of the Poulan 416829 is its powerful engine, which typically features a displacement of around 40cc. This ensures ample cutting power for handling a variety of wood types, from softwoods to hardwoods. The two-stroke engine design enhances fuel efficiency while delivering consistent power throughout the cutting process. The design is both lightweight and compact, allowing for easy maneuverability and reduced user fatigue during extended use.

One of the standout features of the Poulan 416829 is its Easy Start technology. This system is engineered to facilitate a hassle-free starting experience, significantly reducing the effort required to start the chainsaw. Coupled with a primer bulb and adjustable choke, users can expect quick and efficient startups, making it an ideal choice for those who may be new to using chainsaws.

The cutting capacity of the Poulan 416829 is enhanced by its bar length, typically ranging around 16 to 18 inches. This substantial reach allows for tackling a variety of cutting tasks, from pruning branches to felling small trees. The Oregon chain used in this model contributes to smooth cuts and efficient debris removal, making the overall cutting experience more satisfying.

Safety is paramount in chainsaw design, and the Poulan 416829 does not fall short. It includes essential safety features such as a chain brake, which engages in case of kickback, and an anti-vibration system that minimizes vibration during operation. These safety technologies not only protect the user but also enhance comfort during use.

Durability is another key characteristic of the Poulan 416829. Constructed with high-quality materials, the chainsaw is designed to withstand the rigors of outdoor work. The air filtration system helps to prolong engine life by preventing dirt and debris from entering the engine, ensuring reliable performance over time.

In conclusion, the Poulan 416829 is a versatile and user-friendly chainsaw, equipped with powerful technology and safety features that cater to a wide range of cutting needs. Whether you are a homeowner looking to maintain your yard or a professional needing a reliable tool for your work, the Poulan 416829 provides the performance and efficiency necessary to get the job done effectively.
Top Page Image Contents