Poulan 96198002900, PP291EPS27 owner manual To Remove Wheels See Fig, Carburetor, Engine Speed

Page 18

SERVICE AND ADJUSTMENTS

TO REMOVE WHEELS (See Fig. 24)

Remove the klik pin and remove wheel from axle.

IMPORTANT: When installing wheel, be sure to use the axle hole closest to the end of the shaft – do not use the hole in the wheel hub (if equipped). Inner hole in axle and hole in wheel hub are not used for your model snow thrower.

KLIK PIN (INSTALL

OUTER HOLE

IN OUTER HOLE

 

OF AXLE ONLY)

 

AXLE

WHEEL

WHEEL HUB

FIG. 24

NOTE: To seal punctures or prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

ENGINE

See engine manual.

CARBURETOR

Your carburetor is not adjustable. Engine performance should not be affected at altitudes up to 7,000 feet (2,134 meters). If your engine does not operate properly due to suspected carburetor problems, take your snow thrower to a qualified service center.

ENGINE SPEED

Never tamper with the engine governor, which is factory set for proper engine speed. Overspeeding the engine above the factory high speed setting can be dangerous and will void the warranty. If you think the engine-governed high speed needs adjusting, contact a qualified service center, which has proper equipment and experience to make any necessary adjustments.

TO ADJUST CABLE TENSION (See Fig. 25)

Adjust cable tension by turning the adjuster turn buckle, located on the right hand cable. Grasp the long section tightly and turn the short section to lengthen the adjuster. Adjust until cable is snug.

ADJUSTER TURN

BUCKLE

FIG. 25

18

Image 18
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from CartonInstall Speed Control ROD See Figs Install Traction Drive Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotater Head See FigInstall Chute Deflector Remote Control See Figs Check Tire PressurePrimer OperationKnow Your Snow Thrower Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineHOW to USE Your Snow Thrower StoppingTo Adjust Skid Plates See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Move Forward and Backward See FigTo USE Drift Cutters See Fig Before Starting the EngineScraper BAR See Fig Check Engine OIL Level See FigBefore Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has FrozenBefore Each USE MaintenanceGeneral Recommendations LubricationCleaning EngineChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See FigTo Replace Belts See Fig Carburetor To Adjust Cable Tension See FigTo Remove Wheels See Fig Engine SpeedFuel System StorageOther Engine OILTroubleshooting Service Notes Exploded KEY Part Description Auger Bearing Auger HousingScraper BAR Bearing PlugAuger 27 LH Auger 27 RHPlastic Washer Drift Cutter BARCARRIAGEBOLT5/16−18X.750 Lockwasher 5/16Chute Snow Shield Knob BlackPOP Rivet Shield Retainer StrapCable Assembly Heat Shield LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Rotator HeadLower Tube Loop Handle LHLoop Handle RH Pivot SupportKnob RED SpacerRetainer Handle KnobShifter ROD TOP Impeller ROD AssemblyTraction ROD Assembly Shifter ROD BottomHeadlight Bezel Wire HarnessConsole Panel Flood HeadlightRepair Parts Snow Thrower - Model Number PP291EPS27 Drive Exploded Speed Selector AssemblyDrive Plate Assembly Rubber Ring427963X428 Complete LCT EngineFrame Engine Mounting PlateIdler ARM Bracket Impeller BeltTraction Belt Idler PulleyCover Assembly 01.21.014-ACable Bracket LH Cable Bracket RHWheel Lobe CoverWheel Driver Retainer Ring Clutch SlideSafety Ignition KEY 422663DECAL, DANGER, Deflector 181037DECAL, Danger DECAL, InstructionService Notes Limited Warranty