Poulan PP291EPS27, 96198002900 Knob Black, POP Rivet, Chute Snow Shield, Shield Retainer Strap

Page 27

REPAIR PARTS SNOW THROWER - - MODEL NUMBER PP291EPS27 (96198002900)

CONTROL PANEL / CHUTE

5

7

15

3

16

KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION

1420315X428 CHUTE WELDMENT

2178633X428 DEFLECTOR WELDMENT

3421163 DEFLECTOR CONTROL ASSEMBLY

4420325 DEFLECTOR SEAL

	5	414280	KNOB BLACK
	6	128415	POP RIVET
	7	17501010	SCREW 10-24 X .625
	8	419821	CHUTE SNOW SHIELD
	9	419822X004	SHIELD RETAINER STRAP	6
	*10	179829	SHOULDER BOLT 1/4-20 X .375	6
	*10	179829	SHOULDER BOLT 1/4-20 X .375
	*11	191730	NUT 1/4-20
	*12	72250505	CARRIAGE BOLT 3/8-16 X .625
	*13	751153	NUT 5/16-18
	*14	184505	DEFLECTOR SPRING

15420679 (SERVICE PART) DEFLECTOR CONTROL

16421164 (SERVICE PART) DEFLECTOR CABLE GRAY

*14	*11
	*11
2	*10
	*10
4

	6	*13
		*13
1		*12

9	8	01.09.012-A

NOTE:

1.ALL ITEMS INDICATED WITH AN * ARE PROVIDED IN THE BAG OF ITEMS SHIPPED LOOSE WITH PRODUCT.

2.ITEMS 15 AND 16 ARE SERVICE PART NUMBERS TO ALLOW PURCHASE OF INDIVIDUAL ITEMS IF NECESSARY.

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.

27

Image 27

Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Parts Packed Separately in CartonInstall Speed Control ROD See Figs Install Traction Drive Control ROD See FigsUnfold Upper Handle Install Discharge Chute / Chute Rotater Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Install Chute Deflector Remote Control See FigsIgnition KEY OperationKnow Your Snow Thrower PrimerRecoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Adjust Skid Plates See FigCheck Engine OIL Level See Fig Before Starting the EngineScraper BAR See Fig To USE Drift Cutters See FigIf Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before StoppingLubrication MaintenanceGeneral Recommendations Before Each USEEngine CleaningShear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Replace Belts See Fig Engine Speed To Adjust Cable Tension See FigTo Remove Wheels See Fig CarburetorEngine OIL StorageOther Fuel SystemTroubleshooting Service Notes Exploded KEY Part Description Bearing Plug Auger HousingScraper BAR Auger BearingAuger 27 RH Auger 27 LHLockwasher 5/16 Drift Cutter BARCARRIAGEBOLT5/16−18X.750 Plastic WasherShield Retainer Strap Knob BlackPOP Rivet Chute Snow ShieldRotator Head LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Cable Assembly Heat ShieldPivot Support Loop Handle LHLoop Handle RH Lower TubeHandle Knob SpacerRetainer Knob REDShifter ROD Bottom Impeller ROD AssemblyTraction ROD Assembly Shifter ROD TOPFlood Headlight Wire HarnessConsole Panel Headlight BezelRepair Parts Snow Thrower - Model Number PP291EPS27 Drive Exploded Rubber Ring AssemblyDrive Plate Assembly Speed SelectorEngine Mounting Plate Complete LCT EngineFrame 427963X428Idler Pulley Impeller BeltTraction Belt Idler ARM Bracket01.21.014-A Cover AssemblyCable Bracket RH Cable Bracket LHClutch Slide CoverWheel Driver Retainer Ring Wheel Lobe422663 Safety Ignition KEYDECAL, Instruction 181037DECAL, Danger DECAL, DANGER, DeflectorService Notes Limited Warranty