Poulan PP291EPS27, 96198002900 owner manual KEY Part Description

Page 23

REPAIR PARTS SNOW THROWER - - MODEL NUMBER PP291EPS27 (96198002900)

AUGER HOUSING / IMPELLER ASSEMBLY

KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION

1175321X479 IMPELLER

2427148 GEARBOX ASSEMBLY

3	188909	BEARING
4	427146	IMPELLER PULLEY
5	175322	DISCHARGE BASE

6178675X008 CORNER BRACKET

7192199 CLEAN OUT TOOL

8	405400	TOOL CLIP
9	73800400	NUT 1/4-20
10	74780426	SCREW 1/4-20 X .625
11	427942	NUT 5/16-18
12	163183	SCREW 5/16-18 X .625
13	427145	IMPELLER HUB
14	427154	IMPELLER SLEEVE
15	73900600	NUT 3/8-16
16	180355	CARRIAGE BOLT
17	194189	SCREW 13-16 X .625
18	407760	PLUG
19	427302	GEARBOX COVER RH
20	427345	GASKET
21	407770	SEAL
22	407762	BEARING
23	174697	THRUST WASHER 1.00
24	407763	WORM GEAR
25	407764	AUGER SHAFT
26	189282	SQUARE KEY
27	407758	BEARING
28	174683	THRUST WASHER
29	427147	IMPELLER SHAFT
30	7836M	ROLL PIN
31	174681	THRUST WASHER
32	174684	THRUST BEARING
33	407769	BEARING
34	407768	O-RING
35	407767	SCREW 5/16-18 X .750
36	427317	GEARBOX COVER LH

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 23

Image 23

Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Parts Packed Separately in CartonUnfold Upper Handle Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Install Discharge Chute / Chute Rotater Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Install Chute Deflector Remote Control See FigsIgnition KEY OperationKnow Your Snow Thrower PrimerRecoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Adjust Skid Plates See FigCheck Engine OIL Level See Fig Before Starting the EngineScraper BAR See Fig To USE Drift Cutters See FigIf Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before StoppingLubrication MaintenanceGeneral Recommendations Before Each USEEngine CleaningShear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Replace Belts See Fig Engine Speed To Adjust Cable Tension See FigTo Remove Wheels See Fig CarburetorEngine OIL StorageOther Fuel SystemTroubleshooting Service Notes Exploded KEY Part Description Bearing Plug Auger HousingScraper BAR Auger BearingAuger 27 RH Auger 27 LHLockwasher 5/16 Drift Cutter BARCARRIAGEBOLT5/16−18X.750 Plastic WasherShield Retainer Strap Knob BlackPOP Rivet Chute Snow ShieldRotator Head LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Cable Assembly Heat ShieldPivot Support Loop Handle LHLoop Handle RH Lower TubeHandle Knob SpacerRetainer Knob REDShifter ROD Bottom Impeller ROD AssemblyTraction ROD Assembly Shifter ROD TOPFlood Headlight Wire HarnessConsole Panel Headlight BezelRepair Parts Snow Thrower - Model Number PP291EPS27 Drive Exploded Rubber Ring AssemblyDrive Plate Assembly Speed SelectorEngine Mounting Plate Complete LCT EngineFrame 427963X428Idler Pulley Impeller BeltTraction Belt Idler ARM Bracket01.21.014-A Cover AssemblyCable Bracket RH Cable Bracket LHClutch Slide CoverWheel Driver Retainer Ring Wheel Lobe422663 Safety Ignition KEYDECAL, Instruction 181037DECAL, Danger DECAL, DANGER, DeflectorService Notes Limited Warranty