Poulan 96194000501 owner manual To Replace Belts See Fig

Page 16

SERVICE AND ADJUSTMENTS

TO REPLACE BELTS (See Fig. 21)

The auger and traction drive belts are not adjustable. If the belts are damaged or begin to slip from wear, they should be replaced. It is recommended that the belt(s) be replaced by a Sears service centre/department.

NOTE: It is recommended that both the auger and traction drive belt be replaced at the same time.

The V-belts on your snow thrower are of special construction and should be replaced by original equipment manufacturer (OEM) belts available from your nearest Sears service centre/department. Using other than OEM belts can cause personal injury or damage to the snow thrower.

WARNING: Belt replacement requires separation of the snow thrower. While separating the auger housing from the frame assembly, it is important that an assistantstand inthe operating position and hold the snow thrower handles. Se- rious personal injury and/or damage to the unit could occur if the snow thrower should fall during the belt changing process.

FRAME

AUGER

ASSEMBLY

HOUSING

HANDLES

1.REMOVE GASOLINE FROM FUEL TANK - Drain gasoline from fuel tank into a suitable container, out- doors, away from fire or flame. Wipe up any spilled gasoline.

2.REMOVE DISCHARGE CHUTE - Loosen locknut securing chute rotator head to mounting bracket only enough to allow chute rotator head to be raised and discharge chute to be removed from snow thrower.

3.REMOVE BELT COVER - See “TO REMOVE BELT COVER” in this section of this manual.

4.REMOVE ENGINE PULLEY - Remove bolt, lockwasher and flat washer securing pulley to engine crankshaft. Remove outside (auger) pulley only from crankshaft.

5.SEPARATE SNOW THROWER - With your assistant standing in the operating position holding the handles, remove the two (2) bolts holding the auger housing and frame together.

WARNING: As the last bolt is removed, have your assistant carefully lower the handles down to the ground.

6.REMOVE HAIRPIN FROM CLUTCH ROD and remove clutch rod from swing plate. Tip swing plate forward.

7.REMOVE AUGER BELT from around pulley.

8.RELIEVE TENSION ON TRACTION DRIVE BELT IDLER and remove traction drive belt from around pulleys.

HINT: Insert a 3/8" drive ratchet (in the “ON” position) into the square hole in idler arm and rotate ratchet clockwise to relieve tension.

9.With tension relieved on idler, install new traction drive belt around pulleys and inside belt keepers.

10.Install clutch rod in swing plate; secure with hairpin.

11.Place auger belt around and inside the groove of auger pulley only.

12.While your assistant slowly raises handles to rejoin the auger housing and frame assembly, pull up on the auger belt and squeeze sides together above pulley so belt is fully seated in groove of pulley.

13.Bring snow thrower completely together and check carefully for proper routing of belts. If auger belt has become dislodged from the pulley (by catching the idler arm bracket while bringing snow thrower together), separate the snow thrower and repeat step 12. Belt must be fully seated in pulley groove when bringing the snow thrower together.

14.Install the two (2) hex bolts and tighten securely.

15.INSTALL ENGINE PULLEY - Place belt in pulley groove and slide pulley on crankshaft. Install flat washer, lockwasher and bolt and tighten securely (41-47 N-m torque). Make sure belt is inside belt keeper.

16.INSTALL BELT COVER and two (2) screws. Tighten securely.

17.INSTALL DISCHARGE CHUTE – See “INSTALL DIS- CHARGE CHUTE / CHUTE ROTATER HEAD” in the Assembly / Pre-Operation section of this manual.

 

BELT KEEPER

 

 

TRACTION DRIVE BELT

 

ENGINE

FLAT WASHER

 

PULLEY

 

 

 

 

LOCKWASHER

 

 

BOLT

IDLER ARM

AUGER

SQUARE

BELT

HOLE

 

 

CLUTCHING

 

 

IDLER ARM

 

 

BRACKET

 

FRAME

AUGER PULLEY

AUGER

HOUSING

 

 

 

BOLTS

FIG. 21

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATION Remove Snow Thrower from CartonHOW to SET UP Your Snow Thrower Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Tool BOX See FigInstall Discharge Chute / Chute Rotator Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Operation Know Your Snow ThrowerPrimer Ignition KEYMeets A.N.S.I. Safety Requirements HOW to USE Your Snow Thrower StoppingTo Throw Snow See Fig Using the CLEAN-OUT Tool See FigTo Move Forward and Backward See Fig Before Starting the Engine Snow Throwing Tips To Start EngineBefore Stopping If Recoil Starter has FrozenMaintenance Cleaning EngineService and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See FigTo Replace Belts See Fig Storage Troubleshooting OtherPreparación ¡ATENCIÓN! ¡ESTE ALERTO! SU Seguridad Esta ComprometidaFuncionamiento Montaje / PRE-OPERACIÓN Montaje / PRE-OPERACIÓN Sacar LA Máquina Quitanieves DEL CartónComo Preparar SU Máquina Quitanieves Desplegar LA Empuñadura SuperiorMontar LA Biela Montaje DE LA BielaDE Mando DE LA Barrena Ver Figs y Controlar LA Presión DE LOS NeumáticosOperación Familiarícese CON SU Máquina QuitanievesPlacas DE Como Utilizar SU Máquina Quitanieves Controlar LA Eyección DE LA NievePararse Moverse Adelante Y Atrás Ver Fig Lanzar LA Nieve Ver FigUsar LA Herramienta Para Limpiar Ver Fig Antes DE Poner EN Marcha EL Motor Regular LAS Placas DE Deslizamiento Ver FigBarra DE Arrastre Ver Fig Controlar EL Nivel DE Aceite DEL Motor Ver FigConsejos Para Lanzar LA Nieve Puesta EN Marcha DEL MotorAntes DE Parar SI EL Arrancador DE Retroceso SE HA CongeladoRecomendaciones Generales MantenamientoLubricación Limpieza Servicio Y Adjustes Para Ajustar LA Altura DE Máquina QuitanievesConducto Deflector Pernos DE Seguridad Ver FigSustituir LAS Correas Vea Fig Vaciar LA Gasolina DEL Depósito DE CarburanteMotor AlmacenimientoOtros Identificacion DE Problemas   KEY Part Description 205 414280 Knob, Lever Repair Parts Handles Snow Thrower Model Number Repair Parts Snow Thrower Model Number 96194000501 Handles Repair Parts Snow Thrower Model Number 96194000501 Drive Repair Parts Snow Thrower Model Number 96194000501 Drive Page 416717X004 KEY Part Description413429X479 Page 181038 Decal, Danger Limited Warranty

96194000501 specifications

The Poulan 96194000501 is a powerful and versatile tool designed for homeowners and professionals alike, making yard maintenance an efficient and enjoyable task. Packed with features that cater to a variety of lawn care needs, this lawn mower offers exceptional performance and durability.

One of the standout features of the Poulan 96194000501 is its robust engine. Powered by a reliable 4-cycle gasoline engine, it provides the necessary power to tackle even the toughest grass and terrain. The engine is designed for easy starting, eliminating the frustration often associated with traditional pull-start mechanisms. This feature allows users to get right to work without the hassle of prolonged setup and preparation.

The cutting system of the Poulan 96194000501 is engineered for precision and efficiency. It features a wide cutting deck that allows for a broader cutting path, reducing the time spent mowing. The adjustable cutting heights enable users to customize their mowing experience, accommodating various grass types and seasonal changes. This flexibility ensures a clean, even cut that promotes a healthier lawn.

In addition to its performance features, the Poulan 96194000501 is designed with user comfort in mind. The ergonomic handle ensures a comfortable grip, reducing fatigue during extended use. The mower's lightweight design makes it easy to maneuver, allowing users to navigate tight spaces and obstacles with ease. Furthermore, the inclusion of larger rear wheels enhances stability and traction, making it suitable for uneven terrain.

Durability is another key characteristic of the Poulan 96194000501. Constructed with high-quality materials, this mower is built to withstand the rigors of regular use. Its sturdy frame and deck resist wear and tear, ensuring a long lifespan for the product. Additionally, maintenance tasks are simplified, with features that facilitate easy access to the engine and other components.

The Poulan 96194000501 is also eco-friendly, designed to produce lower emissions compared to traditional models. This environmentally conscious approach allows users to maintain their lawns without contributing significantly to pollution, reflecting a growing trend toward sustainable gardening practices.

In summary, the Poulan 96194000501 stands out in the marketplace due to its powerful performance, user-friendly features, and durability. With an efficient cutting system, adjustable heights, ergonomic design, and eco-friendly operation, this lawn mower proves to be an excellent investment for anyone looking to enhance their lawn care experience. Whether for regular maintenance or tackling larger landscaping projects, the Poulan 96194000501 rises to the occasion, making it a reliable choice for all users.
Top Page Image Contents