Poulan 96194000501 owner manual Engine, Cleaning

Page 14

MAINTENANCE

AUGER GEAR CASE

•The gear case was filled with lubricant to the proper level at the factory. The only time the lubricant needs attention is if service has been performed on the gear case.

•If lubricant is required, use only Ronex ED #1 grease.

TRACTION DRIVE SYSTEM

DO NOT lubricate the drive components inside the snow thrower. The sprockets, hex shafts, drive disc and friction wheel require no lubrication. The bearings and bushings are lifetime lubricated and require no maintenance.

CAUTION: Any lubricating of the above compo- nents can cause contamination of the friction wheel and damage to the drive system of your snow thrower.

ENGINE

See engine manual.

LUBRICATION

Use only high quality detergent oil rated with API service classification SG–SL. Select the oil's SAE viscosity grade according to your expected operating temperature.

NOTE: Although multi-viscosity oils (5W30, 10W30 etc.) improve starting in cold weather, these multi-viscosity oils will result in increased oil consumption when used above 32°F. Check your engine oil level more frequently to avoid possible engine damage from running low on oil.

Changetheoilafterevery25hoursofoperationoratleastonce a year if the snow thrower is not used for 25 hours in one year.

Check the crankcase oil level before starting the engine and after each five (5) hours of continuous use. Tighten oil fill cap / dipstick securely each time you check the oil level.

TO CHANGE ENGINE OIL

Determine temperature range anticipated before next oil change. All oil must meet API service classification SG–SL.

•Be sure snow thrower is on level surface.

•Oil will drain more freely when warm.

•Catch oil in a suitable container.

NOTE: The left side wheel may be removed from snow thrower for easier access to the oil drain plug and place- ment of a suitable container. The unit tilted, resting on the frame with the left wheel removed, will help drain any oil trapped inside the engine. (See “TO REMOVE WHEELS” in the Service and Adjustments section of this manual).

1.Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with spark plug.

2.Clean area around drain plug.

3.Remove drain plug and drain oil in a suitable container.

4.Install drain plug and tighten securely.

5.Wipe off any spilled oil from snow thrower and engine.

6.Install left wheel (if removed for draining oil). Be sure to install klick pin into proper hole in wheel axle (See “TO REMOVE WHEELS” in the Service and Adjustments section of this manual).

7.Remove oil fill cap/dipstick. Be careful not to allow dirt to enter the engine.

8.Refill engine with oil through oil dipstick tube. Pour slowly. Do not overfill. For approximate capacity see “PRODUCT SPECIFICATIONS” section of this manual.

9.Use gauge on oil fill cap/dipstick for checking level. Be sure dipstick cap is tightened securely for accurate reading. Keep oil at “FULL” line on dipstick.

10.Wipe off any spilled oil.

MUFFLER

Inspect and replace corroded muffler as it could create a fire hazard and/or damage.

SPARK PLUG

Replace spark plug at the beginning of each season or after every 100 hours of operation, whichever occurs first. Spark plug type and gap setting are shown in the “PRODUCT SPECIFICATIONS” section of this manual.

CLEANING

IMPORTANT: For best performance, keep snow thrower housing free of any dirt or trash. Clean the outside of your snow thrower after each use.

WARNING: Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with spark plug.

•Keep finished surfaces/wheels free of gasoline, oil, etc.

•We do not recommend using a garden hose to clean your snow thrower unless the electrical system, muffler and carburetor are covered to keep water out. Water in engine can result in shortened engine life.

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATION Remove Snow Thrower from CartonInstall Traction Drive Control ROD See Figs HOW to SET UP Your Snow ThrowerInstall Speed Control ROD See Figs Tool BOX See FigCheck Tire Pressure Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotator Head See Fig Primer OperationKnow Your Snow Thrower Ignition KEYMeets A.N.S.I. Safety Requirements HOW to USE Your Snow Thrower StoppingTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig Before Starting the Engine Before Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has FrozenMaintenance Cleaning EngineChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See FigTo Replace Belts See Fig Storage Troubleshooting OtherFuncionamiento ¡ATENCIÓN! ¡ESTE ALERTO! SU Seguridad Esta ComprometidaPreparación Montaje / PRE-OPERACIÓN Montaje / PRE-OPERACIÓN Sacar LA Máquina Quitanieves DEL CartónMontar LA Biela Como Preparar SU Máquina QuitanievesDesplegar LA Empuñadura Superior Montaje DE LA BielaDE Mando DE LA Barrena Ver Figs y Controlar LA Presión DE LOS NeumáticosOperación Familiarícese CON SU Máquina QuitanievesPlacas DE Pararse Controlar LA Eyección DE LA NieveComo Utilizar SU Máquina Quitanieves Usar LA Herramienta Para Limpiar Ver Fig Lanzar LA Nieve Ver FigMoverse Adelante Y Atrás Ver Fig Barra DE Arrastre Ver Fig Antes DE Poner EN Marcha EL MotorRegular LAS Placas DE Deslizamiento Ver Fig Controlar EL Nivel DE Aceite DEL Motor Ver FigAntes DE Parar Consejos Para Lanzar LA NievePuesta EN Marcha DEL Motor SI EL Arrancador DE Retroceso SE HA CongeladoLubricación MantenamientoRecomendaciones Generales Limpieza Conducto Deflector Servicio Y AdjustesPara Ajustar LA Altura DE Máquina Quitanieves Pernos DE Seguridad Ver FigSustituir LAS Correas Vea Fig Vaciar LA Gasolina DEL Depósito DE CarburanteOtros AlmacenimientoMotor Identificacion DE Problemas   KEY Part Description 205 414280 Knob, Lever Repair Parts Handles Snow Thrower Model Number Repair Parts Snow Thrower Model Number 96194000501 Handles Repair Parts Snow Thrower Model Number 96194000501 Drive Repair Parts Snow Thrower Model Number 96194000501 Drive Page 413429X479 KEY Part Description416717X004 Page 181038 Decal, Danger Limited Warranty

96194000501 specifications

The Poulan 96194000501 is a powerful and versatile tool designed for homeowners and professionals alike, making yard maintenance an efficient and enjoyable task. Packed with features that cater to a variety of lawn care needs, this lawn mower offers exceptional performance and durability.

One of the standout features of the Poulan 96194000501 is its robust engine. Powered by a reliable 4-cycle gasoline engine, it provides the necessary power to tackle even the toughest grass and terrain. The engine is designed for easy starting, eliminating the frustration often associated with traditional pull-start mechanisms. This feature allows users to get right to work without the hassle of prolonged setup and preparation.

The cutting system of the Poulan 96194000501 is engineered for precision and efficiency. It features a wide cutting deck that allows for a broader cutting path, reducing the time spent mowing. The adjustable cutting heights enable users to customize their mowing experience, accommodating various grass types and seasonal changes. This flexibility ensures a clean, even cut that promotes a healthier lawn.

In addition to its performance features, the Poulan 96194000501 is designed with user comfort in mind. The ergonomic handle ensures a comfortable grip, reducing fatigue during extended use. The mower's lightweight design makes it easy to maneuver, allowing users to navigate tight spaces and obstacles with ease. Furthermore, the inclusion of larger rear wheels enhances stability and traction, making it suitable for uneven terrain.

Durability is another key characteristic of the Poulan 96194000501. Constructed with high-quality materials, this mower is built to withstand the rigors of regular use. Its sturdy frame and deck resist wear and tear, ensuring a long lifespan for the product. Additionally, maintenance tasks are simplified, with features that facilitate easy access to the engine and other components.

The Poulan 96194000501 is also eco-friendly, designed to produce lower emissions compared to traditional models. This environmentally conscious approach allows users to maintain their lawns without contributing significantly to pollution, reflecting a growing trend toward sustainable gardening practices.

In summary, the Poulan 96194000501 stands out in the marketplace due to its powerful performance, user-friendly features, and durability. With an efficient cutting system, adjustable heights, ergonomic design, and eco-friendly operation, this lawn mower proves to be an excellent investment for anyone looking to enhance their lawn care experience. Whether for regular maintenance or tackling larger landscaping projects, the Poulan 96194000501 rises to the occasion, making it a reliable choice for all users.
Top Page Image Contents