Poulan 96194000502 owner manual To Throw Snow See Fig, Using the CLEAN-OUT Tool See Fig

Page 10

OPERATION

•To change the deflector position, loosen knob, move de- flector to desired position and tighten knob securely.

HIGH

POSITION

KNOB

CHUTE

DEFLECTOR

LOW POSITION

FIG. 13

TO THROW SNOW (See Fig. 14)

The auger rotation is controlled by the auger control lever located on the right side handle.

•Squeeze auger control lever to handle to engage the auger and throw snow.

•Release the auger control lever to stop throwing snow.

AUGER

CONTROL

LEVER

FIG. 14

USING THE CLEAN-OUT TOOL (See Fig. 15)

In certain snow conditions, the discharge chute may be- come clogged with ice and snow. Use the clean-out tool to dislodge this blockage.

When cleaning, repairing, or inspecting, make certain all controls are disengaged and the auger/impeller and all moving parts have stopped. Disconnect the spark plug wire and keep the wire away from the spark plug to pre- vent accidental starting.

•Release the auger control lever and shut off the engine.

•Remove the clean-out tool from it's mounting clip. Grasp the tool firmly by the handle and push and twist the tool into the discharge chute to dislodge the blockage.

After the packed snow has been dislodged, return the clean- out tool to it's mounting clip by pushing it into the clip.

•Make sure the discharge chute is pointed in a safe direc- tion (no vehicles, buildings, people, or other objects are in the direction of discharge) before restarting the engine.

•Restart the engine, then squeeze the auger control lever to the handle to clear snow from the auger hous- ing and the discharge chute.

DISCHARGE CHUTE

CLEAN-OUT

TOOL

MOUNTING

CLIP

FIG. 16

TO MOVE FORWARD AND BACKWARD (See Fig. 16)

SELF-PROPELLING, forward and reverse movement of the snow thrower, is controlled by the traction drive control lever located on the left side handle.

•Squeeze traction drive control lever to handle to engage the drive system.

•Release traction drive control lever to stop the forward or reverse movement of the snow thrower.

SPEED and DIRECTION are controlled by the drive speed control lever.

•Press downward on the speed control lever and move lever to desired position BEFORE engaging the trac- tion drive control lever. Be sure lever springs back and locks into desired position.

CAUTION: Do not move speed control lever when traction drive control lever is engaged. Damage to the snow thrower can result.

•Slower speeds are for heavier snow and faster speeds are for light snow and transporting the snow thrower. It is recommended that you use a slower speed until you are familiar with the operation of the snow thrower.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATIONRemove Snow Thrower from Carton Install Traction Drive Control ROD See Figs HOW to SET UP Your Snow ThrowerInstall Speed Control ROD See Figs Tool BOX See FigInstall Discharge Chute / Chute Rotator Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Primer OperationKnow Your Snow Thrower Ignition KEYMeets A.N.S.I. Safety Requirements HOW to USE Your Snow Thrower StoppingTo Throw Snow See Fig Using the CLEAN-OUT Tool See FigTo Move Forward and Backward See Fig Before Starting the Engine Before Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has FrozenMaintenance Cleaning EngineChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See FigTo Replace Belts See Fig Storage Troubleshooting OtherPreparación ¡ATENCIÓN! ¡ESTE ALERTO! SU Seguridad Esta ComprometidaFuncionamiento Tabla DE Materias Montaje / PRE-OPERACIÓNMontaje / PRE-OPERACIÓN Sacar LA Máquina Quitanieves DEL CartónMontar LA Biela Como Preparar SU Máquina QuitanievesDesplegar LA Empuñadura Superior Montaje DE LA BielaDE Mando DE LA Barrena Ver Figs y Controlar LA Presión DE LOS NeumáticosOperación Familiarícese CON SU Máquina QuitanievesCumple CON LOS Requisitos DE Seguridad DE LA A.N.S.I Como Utilizar SU Máquina Quitanieves Controlar LA Eyección DE LA NievePararse Moverse Adelante Y Atrás Ver Fig Lanzar LA Nieve Ver FigUsar LA Herramienta Para Limpiar Ver Fig Barra DE Arrastre Ver Fig Antes DE Poner EN Marcha EL MotorRegular LAS Placas DE Deslizamiento Ver Fig Controlar EL Nivel DE Aceite DEL Motor Ver FigAntes DE Parar Consejos Para Lanzar LA NievePuesta EN Marcha DEL Motor SI EL Arrancador DE Retroceso SE HA CongeladoLubricación MantenamientoRecomendaciones Generales Maquina QuitanievesMotor LimpiezaConducto Deflector Servicio Y AdjustesPara Ajustar LA Altura DE Máquina Quitanieves Pernos DE Seguridad Ver FigSustituir LAS Correas Vea Fig Vaciar LA Gasolina DEL Depósito DE CarburanteAlmacenimiento OtrosIdentificacion DE Problemas Exploded KEY Part Description Auger 24 LH Auger HousingScrapper BAR Auger 24 RHAuger Bearing Bearing PlugWasher Knob BlackPOP Rivet Plastic WasherRotator Pivot Bracket LEVER/CABLE Rotator AssemblyRotator Head Pulley PivotKnob RED SpacerRetainer Handle KnobLower Handle Panel Bracket LH Panel Bracket RHHandle Grip Pivot Support WeldmentCarriage Bolt 5/16−18 X 155377 NUT 5/16−18 169675 Part KEY Description Repair Parts Snow Thrower Model Number 96194000502 Drive Shoulder Screw Speed Selector AssemblyDrive Plate Assembly END PlateSprocket Axle ShaftRoll PIN 3/16 Clik PINEngine Mount Plate Tecumseh Engine ModelFrame Belt Cover187831X417 Wheel Assembly LH187866X417 Retainer PIN Power CordSafety Ignition KEY WrenchDECAL, Danger DECAL, DANGER, DeflectorService Notes Service Notes Service Notes Limited Warranty
Top Page Image Contents