Poulan 96194000502 owner manual Meets A.N.S.I. Safety Requirements

Page 8

OPERATION

SPARK

PLUG

SAFETY

IGNITION

KEY

CHOKE

CON-

TROL

THROTTLE

/ENGINE

CONTROL

RECOILPOWER

(AUXILIARY) CORD

STARTERPLUG HANDLE

PRIMER

NOTE: ITEMS ABOVE

ARE SHOWN IN

THEIR TYPICAL

LOCATION ON THE

ENGINE. ACTUAL

LOCATION MAY VARY

WITH THE ENGINE

ON YOUR UNIT.

AUGERS

ENGINE OIL CAP

AUGER

WITH DIPSTICK

CONTROL

 

LEVER

GASOLINE

FILLER

CAP

CHUTE

DEFLECTOR

FUEL

SHUT-OFF

VALVE

 

 

DISCHARGE

 

 

CHUTE

ELECTRIC

 

OIL DRAIN PLUG

START

 

 

CLEAN-OUT

BUTTON

 

 

 

TOOL

FIG. 8

DEFLECTOR REMOTE

TRACTION DRIVE

CONTROL LEVER

CONTROL LEVER

DRIVE SPEED

 

CONTROL LEVER

 

LIGHT

DISCHARGE

CHUTE

CONTROL

KNOB

HANDLE

KNOB

MUFFLER

TOOLBOX

SKID PLATE

MEETS A.N.S.I. SAFETY REQUIREMENTS

Our snow throwers conform to the standards of the American National Standards Institute.

Toolbox - used to store spare shear bolts, locknuts and wrench.

Safety ignition key - must be inserted for the engine to start and run. Remove when snow thrower is not in use.

Electric start button - used for starting the engine.

Recoil (auxiliary) starter handle - used for starting engine.

Primer - pumps additional fuel from the carburetor to the cylinder for use when starting a cold engine.

Choke control - used for starting a cold engine.

8

Throttle/engine control - used to select either FAST or SLOW engine speed and to STOP the engine.

Traction drive control lever - used to engage power-pro- pelled forward or reverse motion of snow thrower.

Auger control lever - used to engage auger motion (throw snow).

Discharge chute control knob - used to change the direction the snow is thrown.

Skid plate - used to adjust height of scraper bar from the ground.

Image 8
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Assembly / PRE-OPERATIONParts Packed Separately in Carton HOW to SET UP Your Snow Thrower Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Tool BOX See FigCheck Tire Pressure Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotator Head See Fig Operation Know Your Snow ThrowerPrimer Ignition KEYMeets A.N.S.I. Safety Requirements HOW to USE Your Snow Thrower StoppingTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig Before Starting the Engine Snow Throwing Tips To Start EngineBefore Stopping If Recoil Starter has FrozenMaintenance Cleaning EngineService and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See FigTo Replace Belts See Fig Storage Troubleshooting OtherFuncionamiento ¡ATENCIÓN! ¡ESTE ALERTO! SU Seguridad Esta ComprometidaPreparación Tabla DE Materias Montaje / PRE-OPERACIÓNMontaje / PRE-OPERACIÓN Sacar LA Máquina Quitanieves DEL CartónComo Preparar SU Máquina Quitanieves Desplegar LA Empuñadura SuperiorMontar LA Biela Montaje DE LA BielaDE Mando DE LA Barrena Ver Figs y Controlar LA Presión DE LOS NeumáticosOperación Familiarícese CON SU Máquina QuitanievesCumple CON LOS Requisitos DE Seguridad DE LA A.N.S.I Pararse Controlar LA Eyección DE LA NieveComo Utilizar SU Máquina Quitanieves Usar LA Herramienta Para Limpiar Ver Fig Lanzar LA Nieve Ver FigMoverse Adelante Y Atrás Ver Fig Antes DE Poner EN Marcha EL Motor Regular LAS Placas DE Deslizamiento Ver FigBarra DE Arrastre Ver Fig Controlar EL Nivel DE Aceite DEL Motor Ver FigConsejos Para Lanzar LA Nieve Puesta EN Marcha DEL MotorAntes DE Parar SI EL Arrancador DE Retroceso SE HA CongeladoMantenamiento Recomendaciones GeneralesLubricación Maquina QuitanievesMotor LimpiezaServicio Y Adjustes Para Ajustar LA Altura DE Máquina QuitanievesConducto Deflector Pernos DE Seguridad Ver FigSustituir LAS Correas Vea Fig Vaciar LA Gasolina DEL Depósito DE CarburanteAlmacenimiento OtrosIdentificacion DE Problemas Exploded KEY Part Description Auger Housing Scrapper BARAuger 24 LH Auger 24 RHAuger Bearing Bearing PlugKnob Black POP RivetWasher Plastic WasherLEVER/CABLE Rotator Assembly Rotator HeadRotator Pivot Bracket Pulley PivotSpacer RetainerKnob RED Handle KnobPanel Bracket LH Panel Bracket RH Handle GripLower Handle Pivot Support WeldmentCarriage Bolt 5/16−18 X 155377 NUT 5/16−18 169675 Part KEY Description Repair Parts Snow Thrower Model Number 96194000502 Drive Speed Selector Assembly Drive Plate AssemblyShoulder Screw END PlateAxle Shaft Roll PIN 3/16Sprocket Clik PINTecumseh Engine Model FrameEngine Mount Plate Belt Cover187866X417 Wheel Assembly LH187831X417 Power Cord Safety Ignition KEYRetainer PIN WrenchDECAL, Danger DECAL, DANGER, DeflectorService Notes Service Notes Service Notes Limited Warranty