Poulan PR827ES owner manual HOW to USE Your Snow Thrower, Stopping, To USE Choke Control See Fig

Page 10

OPERATION

The operation of any snow thrower can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear

safety glasses or eye shields while operating 00155 your snow thrower or performing any adjust- ments or repairs. We recommend standard safety glasses

or a wide vision safety mask worn over spectacles.

HOW TO USE YOUR SNOW THROWER

Know how to operate all controls before adding fuel or attempting to start the engine.

STOPPING

TRACTION DRIVE

•Release traction drive control lever to stop the forward or reverse movement of the snow thrower.

AUGER

•Release the auger control lever to stop throwing snow.

ENGINE

1.Move ON / OFF switch to “OFF” position.

2.Remove (do not turn) safety ignition key to prevent unauthorized use.

NOTE: Never use choke to stop engine.

TO USE CHOKE CONTROL (See Fig. 11)

The choke control is located on the engine. Use the choke control whenever you are starting a cold engine. Do not use to start a warm engine.

•To engage choke, turn knob counterclockwise. Slowly turn knob clockwise to disengage.

OFF

 

 

FULL

 

 

 

 

 

FIG. 11

TO CONTROL SNOW DISCHARGE (See Fig. 12)

WARNING: Snow throwers have ex- posed rotating parts, which can cause severe injury from contact, or from ma- terial thrown from the discharge chute. Keep the area of operation clear of all persons, small children and pets at all times including startup.

WARNING: If the discharge chute or auger become clogged, shut-off engine and wait for all moving parts to stop. Use the clean-out tool, NOT YOUR HANDS, to unclog the chute and/or auger.

The DIRECTION in which snow is to be thrown is controlled by the discharge chute control lever.

•To change the discharge chute position, press down- ward on discharge chute control lever and move lever left or right until chute is in desired position. Be sure lever springs back and locks into desired position.

The DISTANCE that snow is thrown is controlled by the position of the chute deflector. Set the deflector low to throw snow a short distance; set the deflector higher to throw snow farther.

•Press downward on chute deflector control lever and move lever forward to raise the deflector and increase the distance. Move lever back to lower the deflector and decrease the distance. Be sure lever springs back and locks into desired position.

DISCHARGE CHUTE

CONTROL LEVER

CHUTE DEFLECTOR

REMOTE CONTROL LEVER

FIG. 12

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from CartonInstall Traction Drive Control ROD See Figs Install Speed Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotator Head See FigInstall Chute Deflector Remote Control See Figs Check Tire PressurePrimer OperationKnow Your Snow Thrower Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineTo USE Choke Control See Fig HOW to USE Your Snow ThrowerStopping To Control Snow Discharge See FigTo Throw Snow See Fig Using the CLEAN-OUT Tool See FigTo Move Forward and Backward See Fig Scraper BAR See Fig To Adjust Skid Plates See FigBefore Starting the Engine Check Engine OIL Level See FigBefore Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has FrozenMaintenance Cleaning EngineChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See FigTo Replace Belts See Fig Carburetor To Adjust Cable Tension See FigTo Remove Wheels See Fig Engine SpeedFuel System StorageOther Engine OILTroubleshooting Service Notes Scraper BAR Auger HousingKEY Part Description Auger BearingSkid Plate LH Auger 27 LHAuger 27 RH Skid Plate RHExploded Bearing Gearbox Assembly178675X008 Corner Bracket Clean OUT Tool Impeller PulleyCable Assembly Heat Shield LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Rotator HeadShoulder Screw Knob BlackPOP Rivet Deflector SpringRepair Parts Snow Thrower - Model NO. PR827ES Handles Interlock Spring Lower TubePivot Support Interlock CAMHandle Knob SpacerKnob RED Washer 3/8Shifter ROD TOP Impeller ROD AssemblyTraction ROD Assembly Shifter ROD BottomRepair Parts Snow Thrower - Model NO. PR827ES Drive Speed Selector AssemblyDrive Plate Assembly Rubber RingSprocket Axle ShaftRoll PIN 3/16 Clik PINFrame Cover AssemblyEngine Model 12A114 423185X428Idler ARM Bracket Impeller BeltTraction Belt Idler Pulley187833X421 Repair Parts Snow Thrower - Model NO. PR827ES WheelsWheel Assembly LH 187865X421Safety Ignition KEY Repair Parts Snow Thrower - Model NO. PR827ES BAG of Parts193071 DECAL, Danger Repair Parts Snow Thrower - Model NO. PR827ES Decals181037 DECAL, DANGER, DeflectorLimited Warranty

PR827ES specifications

The Poulan PR827ES is a powerful and versatile snow blower designed for homeowners who need an efficient solution to tackle winter's toughest challenges. With its robust features and innovative technologies, the PR827ES stands out as a reliable machine for clearing snow from driveways, sidewalks, and other areas.

One of the main features of the Poulan PR827ES is its 27-inch clearing width. This wide clearing path allows users to tackle large areas quickly, making snow removal less time-consuming. Paired with the 21-inch intake height, the PR827ES is capable of handling heavy and deep snow with ease, ensuring that you can clear even the most challenging accumulations.

Equipped with a powerful 247cc engine, the PR827ES delivers the performance needed to cut through packed snow and ice. The engine features an electric start, which provides users with the convenience of starting the machine with the push of a button, eliminating the hassle of manual starting in cold weather conditions.

The PR827ES incorporates a two-stage snow removal system. This system includes an auger that collects the snow and a impeller that throws it out of the chute. This combination ensures efficient snow clearing and allows the user to direct the snow up to 40 feet away, providing flexibility in managing where the snow is thrown.

Another noteworthy characteristic of the Poulan PR827ES is its adjustable chute, allowing users to easily change the direction of the discharged snow from the operator's position. This feature is complemented by the remote deflector, which lets users adjust the height of the snow discharge without having to leave the driver's seat.

The snow blower features heavy-duty wheels that provide excellent traction on slippery surfaces, making it easier to maneuver through uneven terrain and packed snow. The robust construction of the PR827ES ensures durability, while its ergonomic controls provide comfort and ease of use.

Additionally, the Poulan PR827ES is designed with a foldable handle for convenient storage during off-seasons. This feature simplifies the process of storing the snow blower, making it a practical choice for homeowners with limited storage space.

In conclusion, the Poulan PR827ES snow blower combines power, efficiency, and user-friendly features, making it an ideal choice for those looking to simplify their winter snow removal tasks. Its advanced technologies and robust design ensure that you can tackle any winter challenge with confidence.
Top Page Image Contents