Poulan PR827ES owner manual To Replace Belts See Fig

Page 17

SERVICE AND ADJUSTMENTS

TO REPLACE BELTS (See Fig. 20)

The auger and traction drive belts are not adjustable. If the belts are damaged or begin to slip from wear, they should be replaced. It is recommended that the belt(s) be replaced by a service center/department.

NOTE: It is recommended that both the auger and traction drive belt be replaced at the same time.

The V-belts on your snow thrower are of special construc- tion and should be replaced by original equipment manu- facturer (OEM) belts available from your nearest service center/department. Using other than OEM belts can cause personal injury or damage to the snow thrower.

WARNING: Belt replacement requires separation of the snow thrower. While separating the auger housing from the frame assembly, it is important that an assistant stand in the operating position and hold the snow thrower handles. Serious personal injury and/ or damage to the unit could occur if the snow thrower should fall during the belt changing process.

FRAME

AUGER

ASSEMBLY

HOUSING

HANDLES

1.REMOVE GASOLINE FROM FUEL TANK - Drain gasoline from fuel tank into a suitable container, out- doors, away from fire or flame. Wipe up any spilled gasoline.

2.REMOVE DISCHARGE CHUTE - Loosen locknut securing chute rotator head to mounting bracket only enough to allow chute rotator head to be raised and discharge chute to be removed from snow thrower.

3.REMOVE BELT COVER - See “TO REMOVE BELT COVER” in this section of this manual.

4.REMOVE ENGINE PULLEY - Remove bolt, flat washer securing pulley to engine crankshaft. Remove outside (auger) pulley only from crankshaft.

5.SEPARATE SNOW THROWER - With your assistant standing in the operating position holding the handles, remove the two (2) bolts holding the auger housing and frame together.

WARNING: As the last bolt is removed, have your assistant carefully lower the handles down to the ground.

6.REMOVE HAIRPIN FROM CLUTCH ROD and re- move clutch rod from swing plate. Tip swing plate forward.

7.REMOVE AUGER BELT from around pulley.

8.RELIEVE TENSION ON TRACTION DRIVE BELT IDLER and remove traction drive belt from around pulleys.

HINT: Insert a 3/8" drive ratchet (in the “ON” position) into the square hole in idler arm and rotate ratchet clockwise to relieve tension.

9.With tension relieved on idler, install new traction drive belt around pulleys and inside belt keepers.

10.Install clutch rod in swing plate; secure with hairpin.

11.Place auger belt around and inside the groove of auger pulley only.

12.While your assistant slowly raises handles to rejoin the auger housing and frame assembly, pull up on the auger belt and squeeze sides together above pulley so belt is fully seated in groove of pulley.

13.Move idler arm so it does not hit impeller pulley as you bring snow thrower completely together and check carefully for proper routing of belts. If auger belt has become dislodged from the pulley (by catching the idler arm bracket while bringing snow thrower together), separate the snow thrower and repeat step 12. Belt must be fully seated in pulley groove when bringing the snow thrower together.

14.Install the two (2) hex bolts and tighten securely.

15.INSTALL ENGINE PULLEY - Place belt in pulley groove and slide pulley on crankshaft. Install flat washer, bolt and tighten securely (41-47 N-m torque). Make sure belt is inside belt keeper.

16.INSTALL BELT COVER and two (2) screws. Tighten securely.

17.INSTALL DISCHARGE CHUTE – See “INSTALL DIS- CHARGE CHUTE / CHUTE ROTATER HEAD” in the Assembly / Pre-Operation section of this manual.

 

BELT KEEPER

 

 

 

TRACTION DRIVE BELT

 

 

ENGINE

FLAT WASHER

 

PULLEY

 

 

 

 

 

BOLT

 

IDLER ARM

 

AUGER

SQUARE

 

BELT

HOLE

 

 

 

CLUTCHING

 

 

 

IDLER ARM

 

 

 

BRACKET

 

 

FRAME

AUGER PULLEY

AUGER

HOUSING

 

 

 

BOLTS

 

17

FIG. 20

 

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONParts Packed Separately in Carton Remove Snow Thrower from CartonUnfold Upper Handle Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Install Discharge Chute / Chute Rotator Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Install Chute Deflector Remote Control See FigsKnow Your Snow Thrower OperationPrimer Ignition KEYRecoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerTo USE Choke Control See Fig To Control Snow Discharge See FigTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig Before Starting the Engine To Adjust Skid Plates See FigScraper BAR See Fig Check Engine OIL Level See FigTo Start Engine Snow Throwing TipsBefore Stopping If Recoil Starter has FrozenMaintenance Engine CleaningTo Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See FigTo Replace Belts See Fig To Remove Wheels See Fig To Adjust Cable Tension See FigCarburetor Engine SpeedOther StorageFuel System Engine OILTroubleshooting Service Notes KEY Part Description Auger HousingScraper BAR Auger BearingAuger 27 RH Auger 27 LHSkid Plate LH Skid Plate RHExploded 178675X008 Corner Bracket Clean OUT Tool Gearbox AssemblyBearing Impeller PulleyCable Assembly Adjustable LEVER/CABLE Rotator AssemblyCable Assembly Heat Shield Rotator HeadPOP Rivet Knob BlackShoulder Screw Deflector SpringRepair Parts Snow Thrower - Model NO. PR827ES Handles Pivot Support Lower TubeInterlock Spring Interlock CAMKnob RED SpacerHandle Knob Washer 3/8Traction ROD Assembly Impeller ROD AssemblyShifter ROD TOP Shifter ROD BottomRepair Parts Snow Thrower - Model NO. PR827ES Drive Drive Plate Assembly AssemblySpeed Selector Rubber RingRoll PIN 3/16 Axle ShaftSprocket Clik PINEngine Model 12A114 Cover AssemblyFrame 423185X428Traction Belt Impeller BeltIdler ARM Bracket Idler PulleyWheel Assembly LH Repair Parts Snow Thrower - Model NO. PR827ES Wheels187833X421 187865X421193071 Repair Parts Snow Thrower - Model NO. PR827ES BAG of PartsSafety Ignition KEY 181037 Repair Parts Snow Thrower - Model NO. PR827ES DecalsDECAL, Danger DECAL, DANGER, DeflectorLimited Warranty

PR827ES specifications

The Poulan PR827ES is a powerful and versatile snow blower designed for homeowners who need an efficient solution to tackle winter's toughest challenges. With its robust features and innovative technologies, the PR827ES stands out as a reliable machine for clearing snow from driveways, sidewalks, and other areas.

One of the main features of the Poulan PR827ES is its 27-inch clearing width. This wide clearing path allows users to tackle large areas quickly, making snow removal less time-consuming. Paired with the 21-inch intake height, the PR827ES is capable of handling heavy and deep snow with ease, ensuring that you can clear even the most challenging accumulations.

Equipped with a powerful 247cc engine, the PR827ES delivers the performance needed to cut through packed snow and ice. The engine features an electric start, which provides users with the convenience of starting the machine with the push of a button, eliminating the hassle of manual starting in cold weather conditions.

The PR827ES incorporates a two-stage snow removal system. This system includes an auger that collects the snow and a impeller that throws it out of the chute. This combination ensures efficient snow clearing and allows the user to direct the snow up to 40 feet away, providing flexibility in managing where the snow is thrown.

Another noteworthy characteristic of the Poulan PR827ES is its adjustable chute, allowing users to easily change the direction of the discharged snow from the operator's position. This feature is complemented by the remote deflector, which lets users adjust the height of the snow discharge without having to leave the driver's seat.

The snow blower features heavy-duty wheels that provide excellent traction on slippery surfaces, making it easier to maneuver through uneven terrain and packed snow. The robust construction of the PR827ES ensures durability, while its ergonomic controls provide comfort and ease of use.

Additionally, the Poulan PR827ES is designed with a foldable handle for convenient storage during off-seasons. This feature simplifies the process of storing the snow blower, making it a practical choice for homeowners with limited storage space.

In conclusion, the Poulan PR827ES snow blower combines power, efficiency, and user-friendly features, making it an ideal choice for those looking to simplify their winter snow removal tasks. Its advanced technologies and robust design ensure that you can tackle any winter challenge with confidence.
Top Page Image Contents