Poulan PR827ES owner manual Engine, Cleaning

Page 15

MAINTENANCE

AUGER GEAR CASE

•The gear case was filled with lubricant to the proper level at the factory. The only time the lubricant needs attention is if service has been performed on the gear case.

•If lubricant is required, use only Ronex ED #1 grease.

TRACTION DRIVE SYSTEM

DO NOT lubricate the drive components inside the snow thrower. The sprockets, hex shafts, drive disc and friction wheel require no lubrication. The bearings and bushings are lifetime lubricated and require no maintenance.

CAUTION: Any lubricating of the above compo- nents can cause contamination of the friction wheel and damage to the drive system of your snow thrower.

ENGINE

See engine manual.

LUBRICATION

Use only high quality detergent oil rated with API service classification SG–SL. Select the oil's SAE viscosity grade according to your expected operating temperature.

NOTE: Although multi-viscosity oils (5W30, 10W30 etc.) improve starting in cold weather, these multi-viscosity oils will result in increased oil consumption when used above 32°F. Check your engine oil level more frequently to avoid possible engine damage from running low on oil.

Changetheoilafterevery25hoursofoperationoratleastonce a year if the snow thrower is not used for 25 hours in one year.

Check the crankcase oil level before starting the engine and after each five (5) hours of continuous use. Tighten oil fill cap / dipstick securely each time you check the oil level.

TO CHANGE ENGINE OIL

Determine temperature range anticipated before next oil change. All oil must meet API service classification SG–SL.

•Be sure snow thrower is on level surface.

•Oil will drain more freely when warm.

•Catch oil in a suitable container.

NOTE: The left side wheel may be removed from snow thrower for easier access to the oil drain plug and place- ment of a suitable container. The unit tilted, resting on the frame with the left wheel removed, will help drain any oil trapped inside the engine. (See “TO REMOVE WHEELS” in the Service and Adjustments section of this manual).

1.Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with plug.

2.Clean area around drain plug.

3.Remove drain plug and drain oil in a suitable container.

4.Install drain plug and tighten securely.

5.Wipe off any spilled oil from snow thrower and engine.

6.Install left wheel (if removed for draining oil). Be sure to install klick pin into proper hole in wheel axle (See “TO REMOVE WHEELS” in the Service and Adjustments section of this manual).

7.Remove oil fill cap/dipstick. Be careful not to allow dirt to enter the engine.

8.Refill engine with oil through oil dipstick tube. Pour slowly. Do not overfill. For approximate capacity see “PRODUCT SPECIFICATIONS” section of this manual.

9.Use gauge on oil fill cap/dipstick for checking level. Be sure dipstick cap is tightened securely for accurate reading. Keep oil at “FULL” line on dipstick.

10.Wipe off any spilled oil.

MUFFLER

Inspect and replace corroded muffler as it could create a fire hazard and/or damage.

SPARK PLUG

Replace spark plug at the beginning of each season or after every 100 hours of operation, whichever occurs first. Spark plug type and gap setting are shown in the “PRODUCT SPECIFICATIONS” section of this manual.

CLEANING

IMPORTANT: For best performance, keep snow thrower housing free of any dirt or trash. Clean the outside of your snow thrower after each use.

WARNING: Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with plug.

•Keep finished surfaces/wheels free of gasoline, oil, etc.

•We do not recommend using a garden hose to clean your snow thrower unless the electrical system, muffler and carburetor are covered to keep water out. Water in engine can result in shortened engine life.

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Parts Packed Separately in CartonInstall Speed Control ROD See Figs Install Traction Drive Control ROD See FigsUnfold Upper Handle Install Discharge Chute / Chute Rotator Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Install Chute Deflector Remote Control See FigsIgnition KEY OperationKnow Your Snow Thrower PrimerRecoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety RequirementsTo Control Snow Discharge See Fig HOW to USE Your Snow ThrowerStopping To USE Choke Control See FigUsing the CLEAN-OUT Tool See Fig To Throw Snow See FigTo Move Forward and Backward See Fig Check Engine OIL Level See Fig To Adjust Skid Plates See FigBefore Starting the Engine Scraper BAR See FigIf Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before StoppingMaintenance Engine CleaningShear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Replace Belts See Fig Engine Speed To Adjust Cable Tension See FigTo Remove Wheels See Fig CarburetorEngine OIL StorageOther Fuel SystemTroubleshooting Service Notes Auger Bearing Auger HousingKEY Part Description Scraper BARSkid Plate RH Auger 27 LHAuger 27 RH Skid Plate LHExploded Impeller Pulley Gearbox Assembly178675X008 Corner Bracket Clean OUT Tool BearingRotator Head LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Cable Assembly Heat ShieldDeflector Spring Knob BlackPOP Rivet Shoulder ScrewRepair Parts Snow Thrower - Model NO. PR827ES Handles Interlock CAM Lower TubePivot Support Interlock SpringWasher 3/8 SpacerKnob RED Handle KnobShifter ROD Bottom Impeller ROD AssemblyTraction ROD Assembly Shifter ROD TOPRepair Parts Snow Thrower - Model NO. PR827ES Drive Rubber Ring AssemblyDrive Plate Assembly Speed SelectorClik PIN Axle ShaftRoll PIN 3/16 Sprocket423185X428 Cover AssemblyEngine Model 12A114 FrameIdler Pulley Impeller BeltTraction Belt Idler ARM Bracket187865X421 Repair Parts Snow Thrower - Model NO. PR827ES WheelsWheel Assembly LH 187833X421Repair Parts Snow Thrower - Model NO. PR827ES BAG of Parts Safety Ignition KEY193071 DECAL, DANGER, Deflector Repair Parts Snow Thrower - Model NO. PR827ES Decals181037 DECAL, DangerLimited Warranty

PR827ES specifications

The Poulan PR827ES is a powerful and versatile snow blower designed for homeowners who need an efficient solution to tackle winter's toughest challenges. With its robust features and innovative technologies, the PR827ES stands out as a reliable machine for clearing snow from driveways, sidewalks, and other areas.

One of the main features of the Poulan PR827ES is its 27-inch clearing width. This wide clearing path allows users to tackle large areas quickly, making snow removal less time-consuming. Paired with the 21-inch intake height, the PR827ES is capable of handling heavy and deep snow with ease, ensuring that you can clear even the most challenging accumulations.

Equipped with a powerful 247cc engine, the PR827ES delivers the performance needed to cut through packed snow and ice. The engine features an electric start, which provides users with the convenience of starting the machine with the push of a button, eliminating the hassle of manual starting in cold weather conditions.

The PR827ES incorporates a two-stage snow removal system. This system includes an auger that collects the snow and a impeller that throws it out of the chute. This combination ensures efficient snow clearing and allows the user to direct the snow up to 40 feet away, providing flexibility in managing where the snow is thrown.

Another noteworthy characteristic of the Poulan PR827ES is its adjustable chute, allowing users to easily change the direction of the discharged snow from the operator's position. This feature is complemented by the remote deflector, which lets users adjust the height of the snow discharge without having to leave the driver's seat.

The snow blower features heavy-duty wheels that provide excellent traction on slippery surfaces, making it easier to maneuver through uneven terrain and packed snow. The robust construction of the PR827ES ensures durability, while its ergonomic controls provide comfort and ease of use.

Additionally, the Poulan PR827ES is designed with a foldable handle for convenient storage during off-seasons. This feature simplifies the process of storing the snow blower, making it a practical choice for homeowners with limited storage space.

In conclusion, the Poulan PR827ES snow blower combines power, efficiency, and user-friendly features, making it an ideal choice for those looking to simplify their winter snow removal tasks. Its advanced technologies and robust design ensure that you can tackle any winter challenge with confidence.
Top Page Image Contents