Poulan PR10527ESA Operation, TO THROW SNOW See Fig, USING THE CLEAN-OUT TOOL See Fig, Clean-Out

Page 11
TO THROW SNOW (See Fig. 15)

OPERATION

TO THROW SNOW (See Fig. 15)

The auger rotation is controlled by the auger control lever located on the right side handle.

Squeeze auger control lever to handle to engage the auger and throw snow.

Release the auger control lever to stop throwing snow.

AUGER

CONTROL

LEVER

FIG. 15

USING THE CLEAN-OUT TOOL (See Fig. 16)

In certain snow conditions, the discharge chute may be- come clogged with ice and snow. Use the clean-out tool to dislodge this blockage.

When cleaning, repairing, or inspecting, make certain all controls are disengaged and the auger/impeller and all moving parts have stopped. Disconnect the spark plug wire and keep the wire away from the spark plug to pre- vent accidental starting.

Release the auger control lever and shut off the engine.

Remove the clean-out tool from it's mounting clip. Grasp the tool fi rmly by the handle and push and twist the tool into the discharge chute to dislodge the blockage.

After the packed snow has been dislodged, return the clean- out tool to it's mounting clip by pushing it into the clip.

DISCHARGE CHUTE

CLEAN-OUT

TOOL

MOUNTING CLIP

Make sure the discharge chute is pointed in a safe di- rection (no vehicles, buildings, people, or other objects are in the direction of discharge) before restarting the engine.

Restart the engine, then squeeze the auger control lever to the handle to clear snow from the auger hous- ing and the discharge chute.

TO MOVE FORWARD AND BACKWARD (See Fig. 17)

SELF-PROPELLING, forward and reverse movement of the snow thrower, is controlled by the traction drive control lever located on the left side handle.

Squeeze traction drive control lever to handle to engage the drive system.

Release traction drive control lever to stop the forward or reverse movement of the snow thrower.

SPEED and DIRECTION are controlled by the drive speed control lever.

Press downward on the speed control lever and move lever to desired position BEFORE engaging the trac- tion drive control lever. Be sure lever springs back and locks into desired position.

CAUTION: Do not move speed control lever when traction drive control lever is engaged. Damage to the snow thrower can result.

Slower speeds are for heavier snow and faster speeds are for light snow and transporting the snow thrower. It is recommended that you use a slower speed until you are familiar with the operation of the snow thrower.

NOTE: When both traction drive and auger control levers are engaged, the traction drive control lever will lock the auger control lever in the engaged position. This will allow you to release your right hand from the handle and adjust the discharge chute direction without interrupting the snow throwing process.

TRACTION DRIVE

CONTROL LEVER

DRIVE SPEED

CONTROL LEVER

FIG. 17

FIG. 16

11

Image 11
Contents PR10527ESA OWNERS MANUAL MODEL NUMBERSNOW THROWER IMPORTANT MANUALPREPARATION SAFETY RULESSafe Operation Practices for Snow Throwers TRAININGCUSTOMER RESPONSIBILITIES MAINTENANCE AND STORAGEPRODUCT SPECIFICATIONS PRODUCT SPECIFICATIONS PARTS PACKED SEPARATELY IN CARTONSERVICE AND ADJUSTMENTS SAFETY RULESINSTALL SPEED CONTROL ROD See Figs. 1 and ASSEMBLY / PRE-OPERATIONHOW TO SET UP YOUR SNOW THROWER REMOVE SNOW THROWER FROM CARTONINSTALL AUGER CONTROL ROD See Figs. 5 and INSTALL TRACTION DRIVE CONTROL ROD See Figs. 3 andCHECK TIRE PRESSURE INSTALL DISCHARGE CHUTE / CHUTE ROTATER HEAD See FigINSTALL CHUTE DEFLECTOR REMOTE CONTROL See Figs. 8 and KNOW YOUR SNOW THROWER OPERATIONRecoil auxiliary starter handle - used for starting the MEETS A.N.S.I. SAFETY REQUIREMENTSDeflector remote control lever - used to change the Drive speed control lever - used to select forward orTO USE THROTTLE CONTROL See Fig HOW TO USE YOUR SNOW THROWERSTOPPING TO USE FUEL SHUT-OFF VALVE See FigTO MOVE FORWARD AND BACKWARD See Fig USING THE CLEAN-OUT TOOL See FigCLEAN-OUT TO THROW SNOW See FigCHECK ENGINE OIL LEVEL See Fig BEFORE STARTING THE ENGINETO ADJUST SKID PLATES See Fig SCRAPER BARIF RECOIL STARTER HAS FROZEN SNOW THROWING TIPSBEFORE STOPPING LUBRICATION MAINTENANCEGENERAL RECOMMENDATIONS BEFORE EACH USEAUGER GEAR CASE CLEANINGENGINE V-BELTSCHUTE DEFLECTOR SERVICE AND ADJUSTMENTS1. Be sure throttle is in STOP position 2. Remove safety ignition key TO ADJUST SNOW THROWER HEIGHTTO REPLACE BELTS See Fig CARBURETOR STORAGEOTHER TO REMOVE WHEELS See FigEngine idles or TROUBLESHOOTINGLoss of power Does not startLIMITED WARRANTY